Prevue Hendryx 532 User manual

S3.B
S3.A
Align holes to
ove lapping
532—11/ 22 — A4.1 Made in China for Prevue Pet Products, Inc., 224 N Maplewood Ave, Chicago IL 60612 USA • 1 [312 243-3624 • www.prevuepet.com • customerservice @ prevuepet.com
KEY: R=Roof
S=Side pie es
BK = Ba k pie es
B=Base
F=Front pie es
Jumbo Small Animal Home
PARTS LIST
ASSEMBLY
Instru tions online at www.prevuepet. om
]F1
]F2
]F3
]S1.B
]S1.A
]S2.A
]S2.B
S3.B
S3.A
]S1.B
]S1.A
]S2.A
]S2.B
]B
]Bk1
]Bk2
]Bk3
]R
Hex Screw
8 pcs (long)
Hex Screw
1 pc (short)
indbell Lock
+ Screw
Hex Key + rench
CUSTOMER SUPPORT
Please onta t Prevue Pet Produ ts:
PHONE [phone]
ONLINE www.prevuepet. om
EMAIL customerservice@ prevuepet.com
Heavy ve tical ails
face DOWN
T ay channels
face UP
Loop
faces UP
See notes on Pa ts o ientation.
With the S1frame laying flat,
insert the S2mesh into the
holes at the top of the frame.
Insert the S3frame bar
between the frame legs.
Slide up arefully, inserting the
mesh into the top holes, and aligning
the holes along the frame legs.
532
MODEL #
1PIECES
PREASSEMBLE THE SIDE PANELS
Inter hangeable:
]S1.A= ]S1.B
]S2.A= ]S2.B
]S3.A= ]S3.B
⁕
PLATFORM
CASTERS
RAMP
interchangeable
interchangeable
interchangeable

Bk2
Bk3
Bk1
For more wonderful cages, toys, and accessories for cats, birds, chickens, rabbits, ferrets, dogs and small animals, visit www.prevuepet.com532 — 11/22 — A4.2
]1
]4
]2
]3
1Atta h the front lower rail (with windbell lock)
to the assembled side panels.
2Insert all extended wires along the front panel
into the holes of the frame rail.
3Insert the front upper frame rail onto the
extended wires along the top of the front panel.
4Atta h the frame rail to the side panels with
long hex s rews.
× 4
F2
F3
F1
× 4
View f om f ame ail end. An open
ci cle indicates holes along that
ve tical o ho izontal side.
View f om f ame ail
end. An open ci cle
indicates holes
along that ve tical
o ho izontal side.
View f om f ame ail end. An open
ci cle indicates holes along that
ve tical o ho izontal side.
View f om f ame ail end. An open
ci cle indicates holes along that
ve tical o ho izontal side.
T ay channels
face the Inte io
Holes on
lowe f ame
ail face UP
See notes on the o ientation of Pa ts.
Atta h the front lower frame rail to the
side panels with long hex s rews.
Leave s rews loose at this stage.
2PIECES
Thick ve tical wi es
face the cage Exte io
Thick ve tical
wi es face the
cage Exte io
]5]6
]7
Same assembly as the front,
with these ex eptions:
5Atta h the back lower frame rail with long hex
s rews. On both sides, atta h the s rew just
enough to hold the rail.
6Insert the back panel.
7Add the back upper frame rail.
8Atta h the frame rail, loosely, with long hex
s rews.
]8

532—11/ 22 — A4.3 Made in China for Prevue Pet Products, Inc., 224 N Maplewood Ave, Chicago IL 60612 USA • 1 [312 243-3624 • www.prevuepet.com • customerservice @ prevuepet.com
Carefully tip the age on its side.
Hand-tighten the asters into the
frame legs and, to get them fully
inserted, finish tightening with
the en losed wren h.
3PIECES
4PIECES
]1
]1
]2
]4
1Insert the extended wires on the roof
panel into the small holes on the side
frames, just above the frame rail.
Make sure the bra ket in the enter
goes over the frame rail and rests
on the age interior.
2Push the ba k/side panel seam
together to se ure the extended wires
in pla e. Tighten the hex s rews
ompletely.
Tighten up ALL screws over
the entire cage for a
stable and secure
assembly.
3With the short hex s rew, atta h
the roof panel bracket from the
ba k, through the frame rail, into
the bra ket on the age interior.
4Close the roof and at h the front
edge wire under the alternating
hooked tabs along the top frame rail.
CASTERS
RENCH
R
Tab spacing is condensed fo the
pu poses of illust ating wi e position.
× 1
short
]3

B
For more wonderful cages, toys, and accessories for cats, birds, chickens, rabbits, ferrets, dogs and small animals, visit www.prevuepet.com532—11 /22 — A4.4
Atta h the ramp to either end of the
platform: at h the slotted holes on the
ramp under the hooked bra kets and
pull up to li k into pla e.
For ease of insertion, open the roof and the
front door. Angle the platform down into the
age and slide the platform into position
horizontally.
Cat h all hooked platform tabs
onto age wires of the
same height.
Turn the age upright and
slide the base into pla e.
Atta h the windbell lock
with a shortest hex s rew.
5PIECES
6PIECES
Assembly ompleted. {
PLATFORM RAMP
INDBELL
LOCK + SCRE