Prevue Hendryx 3453 User manual

CUSTOMER SUPPORT
For assistan e or repla ement parts,
please onta t Prevue Pet Produ ts:
PHONE [phone]
ONLINE www.prevuepet. om
EMAIL customerservice @ prevuepet.com
3453
MODEL #
3453 — 03 /19 — USL Made in China for Prevue Pet Products, Inc., 224 N Maplewood Ave, Chicago IL 60612 USA • 1 [312 243-3624 • www.prevuepet.com • customerservice @ prevuepet.com
Stainless Steel
Playtop Home
PARTS LIST
Instru tions online at www.prevuepet. om
]Pc
]Cc
]Ls
]Rs
]R
]B
]F
Phillips-head screws
18 pcs (installed in place
on cage panels)
Hex screws
4 pcs (installed in place
on playtop bar supports)
Knobs
4 pcs (installed in place
on cage & playtop bar)
(plus bagged extras :
hardware & duplicate
screws)
]C
Casters
4 pcs
HARDWARE
INCLUDED:
TOOLS
INCLUDED:
KE :
B = Ba k panel
LS = Left Side panel
F = Front panel
RS = Right Side panel
R = Roof grille
C = Casters
PC = Playtop Components
CC = Cage Components
Allen wrench
TOOLS NOT
INCLUDED:
Phillips-head
screwdriver

]R
]B
]Ls
]Rs
]F
KE :
B = Ba k panel
F = Front panel
LS = Left side
panel
RS = Right side
panel
R = Roof grille
C = Casters
CC = Cage
Components
PC = Playtop
Components
CUSTOMER SUPPORT
For assistan e or repla ement parts,
please onta t Prevue Pet Produ ts:
PHONE [phone]
ONLINE www.prevuepet. om
EMAIL customerservice @ prevuepet.com
3453 — 03/19 — USL Made in China for Prevue Pet Products, Inc., 224 N Maplewood Ave, Chicago IL 60612 USA • 1 [312 243-3624 • www.prevuepet.com • customerservice @ prevuepet.com
Instru tions online at www.prevuepet. om
TOOLS NEEDED : Phillips head s rewdriver • For best results, follow Assembly Steps in order presented.
2PIECES
3453 Stainless Steel
Playtop Home
MODEL #
]C
1PIECES
Ba k the Phillips-
head s rews out,
align the side panel
unit with the front panel
unit, and re-tighten the
s rews to atta h.
Repeat this method for all
panel units to assemble
the age body.
Set the cage roof grille
in position and atta h with
Phillips-head s rews.
S rews are installed in pla e. When atta hing
panels or omponents, ba k the s rew out, mat h
up the omponents, and reinsert to atta h.
⁕
In most ases, we re ommend
two people assemble this age.
⁕
Note: On the back panel, the small loop
should face the interior. This loop helps
hold the bottom grille in place.
While the lockable rolling
casters an be added at any
point in the assembly, we
re ommend installing them
at this time.
S rew the threaded aster post
into the frame leg at ea h orner.
If preferred, tighten ea h aster by
the base nut with a slim wren h.

]Pc
]Cc
3453 — 03 /19 — USL For more wonderful cages, toys, and accessories for dogs, cats, birds, chickens, rabbits, ferrets and small animals, visit www.prevuepet.com
3PIECES
4PIECES
Assembly ompleted. {
Loosen the knob s rews on the per h bar rail and along the
age front. Insert the ladder and re-tighten the knob s rews.
Remove the hex s rews from the ends of the
per h bar supports. Install the perch bar supports
on the ba k panel of the age.
Cups/cup holders:
Open the up door.
Insert the s rew post
on the up holder
through the door
mesh, add the bra ket
on the outside, and
tighten to the door
with a wing nut.
Pla e a deep up into
the holder.
Grille and tray:
Open the grille lo k.
Slide the grille (with
handle) into the top
hannel and the deep
tray into the bottom
hannel.
Perch:
Hold the per h in pla e in the
age interior. On the exterior, align
a Phillips-head s rew through the
bra ket, through the age wire, into
the per h bra ket. Tighten. Requires
four s rews to se ure the per h bar.
When fully assembled, he k and tighten
ALL s rews and wing nuts over the entire
age to ensure a safe and stable home.
⁕
Atta h the perch bar unit to the support rails
with allen-head s rews.
Loosen the per h bra e s rews and tilt the per h ba k.
Install the up holder bra kets using Phillips-head s rews.
Rotate the per h ba k in pla e and retighten the bra e
s rews. Insert the shallow cups.
Open the grille lo k.
Slide the thin grille
into the top hannel
and the shallow tray
into the bottom
hannel.
Shortest side →
Longest side
↓