Pride Mobility SilverStar Wheelchair/Scooter Lift User manual

BackpackerBackpacker
BackpackerBackpacker
Backpacker

www.pridemobility.com Backpacker
SAFETY GUIDELINES
Copyright © 2006
Pride Mobility Products Corp.
INFMANU3109/Rev B/April 2006
This product is manufactured by:
Silver Star Mobility
578 Mason Way
Medford, Oregon 97501
The symbols below are used throughout this owner's manual and on the product to identify warnings and
important information. It is very important for you to read them and understand them completely.
WARNING! Failure to follow designated procedures can cause either personal injury,
component damage, or malfunction (black symbol on yellow triangle with black border).
MANDATORY! These actions should be performed as specified. Failure to perform
mandatory actions can cause injury to personnel and/or damage to equipment (white
symbol on blue dot with white border).
PROHIBITED! These actions should be prohibited. These actions should not be performed
at any time or in any circumstances. Performing a prohibited action can cause injury to
personnel and/or damage to equipment (black symbol with red circle and red slash).
Please fill out the following information for quick reference:
PrideProvider:_____________________________________________________________________
Address:__________________________________________________________________________
Phone Number: ___________________
Purchase Date:____________________ SerialNumber:_________________________________
NOTE: This owner’s manual is compiled from the latest specifications and product information avail-
able at the time of publication. We reserve the right to make changes as they become necessary. Any
changes to our products may cause slight variations between the illustrations and explanations in this
manual and the product you have purchased.

Backpacker www.pridemobility.com 3
CONTENTS
I. INTRODUCTION......................................................................................................................... 4
II. SAFETY......................................................................................................................................... 6
III. INSTALLATION .......................................................................................................................... 8
IV. OPERATION............................................................................................................................... 13
V. BATTERY CHARGING........................................................................................................... 15
VI. CARE AND MAINTENANCE ................................................................................................ 16
VII. TROUBLESHOOTING............................................................................................................ 18
VIII.SPECIFICATIONS ................................................................................................................... 19
IX. WARRANTY................................................................................................................................20

4 www.pridemobility.com Backpacker
Welcome to Pride Mobility Products Corporation (Pride). Congratulations on the purchase of your new
Backpacker Lift System. The Backpacker Lift System design combines the most advanced state-of-the-art
componentswithmodern,attractive styling.We are certain that the designfeaturesandtrouble-free operation
will add convenience to your daily living and ensure complete satisfaction.
At Pride, your safety is important to us. Please read and follow all instructions in this manual before
operating your lift system for the first time. These instructions were produced for your benefit. Your
understanding of these instructions is essential for the safe operation of your new lift system.
Pride is not liable for damage to property or personal injury arising out of the unsafe use of a Backpacker
Lift System. Pride is also not liable for any property damage or personal injury arising out of the failure of
any person and/or user to follow the instructions and recommendations set forth in this manual or any other
instructions or recommendations contained in other Backpacker Lift System related literature issued by
Pride or contained on the Backpacker Lift System itself.
INTERNET AND PRIVATE PURCHASES
If you purchased your product over the internet or from a previous owner and you have any questions about
the safe use and/or maintenance of the product, please visit Pride’s web site www.pridemobility.com or
contact your authorized Pride Provider.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter, or modify this product or
remove or render inoperable or unsafe any guards, shields, or other safety features of this product; fail,
refuse,orneglect toinstallanyretrofitkitsfromtimeto timeprovidedbyPridetoenhanceorpreserve thesafeuse
ofthis product.
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear
about the safety and reliability of your new lift system, and about the service you received from your
authorized Pride Provider.
Please notify us of any change of address, so we can keep you apprised of important information about
safety, new products, and new options that can increase your ability to use and enjoy your new lift system.
Please feel free to contact us at the address below:
PrideMobilityProductsCorporation
Attn.:CustomerCareDepartment
182SusquehannaAve.
Exeter, PA18643-2694
[e-mail]
800.424.8205
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact
us and we will be glad to send you a new one immediately.
I. INTRODUCTION

Backpacker www.pridemobility.com 5
I. INTRODUCTION
PRIDE OWNERS CLUB
As an owner of a Pride product, you are encouraged to enroll in the Pride Owners Club. Complete and
return your enclosed product registration card or visit Pride’s web site at www.pridemobility.com. As a
registered member, each time you visit our site, you have access to the most interactive, educational venue
available today for people with mobility needs, their families, and friends.
From our home page, select “Owners Club” to enter a page dedicated to current and potential Pride product
owners. You will gain access to interviews, stories, recreation ideas, daily living tips, product and funding
information, and interactive message boards. These message boards invite you to communicate with other
Pride customers as well as Pride representatives who are available to assist you with any questions or
concerns you may have.

6 www.pridemobility.com Backpacker
II. SAFETY
PRODUCT SAFETY SYMBOLS
The symbols below are used on the lift system to identify warnings, mandatory actions, and prohibited
actions. It is very important for you to read and understand them completely.
Crush Hazard—Pinch/crush points created during assembly and operation.
Keep hands clear.
Crush Hazard—Moving parts can crush and cut. Keep hands clear.
Removal of grounding prong can create electrical hazard. If necessary,
properly install an approved 3-pronged adapter to an electrical outlet having
2-pronged plug access. Failure to heed could result in personal injury and/
or property damage.
Prevent personal injury and equipment damage. Do not connect an extension
cord to the charger cord.
Read and follow the information in the owner’s manual.
Maximum lifting capacity.
Lift system intended for use with unoccupied mobility device. Do not use
product to lift people.
Do not use as a step.
D
W
R
1
2
3
4
L
0
0
4
R
E
V
A
Do not sit on mobility device while activating lift or during transport.
Do not sit on Power Chair or
Scooter while activating lift
or during transport.
Crush Hazard—Moving lift can crush. Keep feet clear during operation.

Backpacker www.pridemobility.com 7
LIFTING CAPABILITIES
The Backpacker Lift System is designed for a maximum lifting capacity of 325 lbs. (147 kg). Under no
circumstances should the Backpacker Lift System be made to exceed this weight limit. Subjecting the lift
system to the strain of hoisting more than it is designed to lift may cause it to fail, resulting in damage to the
mobility device and/or the lift operator. Refer to the mobility device owner’s manual for information on the
overall weight of the mobility device before lifting.
WARNING! Adding accessories, oversize batteries, or a different seat will increase the
weight of your mobility device. Verify with your authorized Pride Provider that the total
weight of your mobility device, including additions, does not exceed 325 lbs. (147 kg).
INSTALLATION
YourBackpackerLiftSystemisaninsidevanliftdesignedforinstallationintovariousbrandsoffull-sizedandmini
vans.Readandfullyunderstandtheinstallationinstructionsprovidedinthismanualandrelatedliteratureforyour
brandofvehiclebeforeinstallingtheliftsystem.
LIFTING NON-PRIDE PRODUCTS
TheBackpackerLiftSystemisanextremelyversatiledevicewhichusersmayemploytoliftitemsotherthanPride
products.Pride has nocontrolover such use,nor can Prideanticipateevery possible usetowhich aBackpacker
LiftSystemmaybeput.Liftingnon-Pride productswiththeBackpackerLiftSystemisdoneattheoperator’sown
risk,andPrideacceptsno liabilityfor damageorinjuryresultingfromsuchuse.
PRELIFT INSPECTION
Before operating the Backpacker Lift System, conduct a careful survey of your surroundings to ensure that
the lift system has a clear path of operation. Remove any possible obstructions before operating the lift and
do not allow children to operate or play near the lift.
OPERATOR POSITIONING
The operator of the lift should stand a safe distance from the unit being lifted/lowered to ensure that his/her
feet are never positioned under the raised lift platform. The operator should also keep his/her hands clear of
the lift system to avoid the potential for injury.
TRANSPORT VEHICLE POSITIONING
Be sure your vehicle is parked on flat, level ground before attempting to load, lift, or remove a mobility
device with the Backpacker Lift System. Make sure the vehicle emergency park brake is engaged before
loading or unloading a mobility device.
II. SAFETY

8 www.pridemobility.com Backpacker
III. INSTALLATION
BACKPACKER LIFT SYSTEM INSTALLATION
WARNING! Prevent product and/or vehicle damage! The Backpacker Lift should be installed
by an authorized service technician only.
NOTE: Use only the supplied hardware to install the Backpacker Lift System.
NOTE: If you are installing the Backpacker into a full-sized van, refer to the information provided in
separate literature for side-entry securement system installation. If you are installing the Backpacker
into a mini van, refer to the following information.
Follow these steps to install the Backpacker:
1. Removetherearseat fromthevanaccordingto thevehicle manufacturerremovalinstructions.
2. Route the Backpacker wiring harness through the vehicle. See “Wiring Harness Installation.”
WARNING! Prevent product damage! Route the wiring harness through the vehicle rather
than under the vehicle to avoid coming in contact with sharp edges, extreme temperatures,
moving parts, and roadway debris. Power shorts may occur if wires come in contact with
hot exhaust parts or sharp edges.
WARNING! Never attach the wiring harness to a secondary power source. Do not attempt
to use trailer wiring to power the lift system. The wiring harness must be connected
directly to the vehicle battery.
NOTE: If your lift is equipped with an optional onboard battery, refer to “Onboard Battery Installation.”
Figure 1. Basic Securement System Installation
FLOOR PLATE
MOUNTINGHARDWARE
MID-RISERBAR
3. Positionasecurementsystemfloorplateovereach
set of floor locks that hold the rear seat to the
floorof thevan.See figure1.
NOTE: Securement systems vary depending on
vehicle manufacturer. While these instructions
describe basic installation for most vehicles,
your securement system may require separate
parts based on the make of your vehicle. Refer
to the installation instructions supplied with
your securement system or contact your autho-
rized Pride Provider for more information.
4. Secure each floor plate to the floor of the van
usingthesuppliedmountinghardware.Seefigure
1.Donot fullytightenthemountinghardware at
thistime.
5. Position the mid-riser bar over the floor plate
closest to the rear of the vehicle, aligning the
mountingholesinthemid-riserbarwith thosein
thefloor plate.Seefigure 1.

Backpacker www.pridemobility.com 9
III. INSTALLATION
Figure 2. Backpacker Installation
6. Remove theshippingcleat fromthe Backpackerstopblock anddiscard itandthe mountingnut.
7. Installtheboltyouremovedfromthe shippingcleatintothestopblockontheBackpackerandsecure withthe
suppliednut.Seefigure2.
8. Connect theBackpackerwiring harnesstothe handcontrol.
9. Place the Backpacker uponblocks,so that there is at least 1-foot of clearanceundertheframe.
10. Connect the Backpacker to a power source.
11. Reachunder theBackpackertruck frameand simultaneously pressthe microswitch andthe “UP” buttonon
the handcontroltoraise the tower 4-6 in. See figure 2.
12. Carefullyslide theBackpacker intothe rearof thevanandcenteritoverthethreadedholesinthe floorplates.
Seefigure 2.Make surethemid-riser baris stillproperlyaligned.
WARNING! Lifting weight beyond your physical capability can result in personal injury. At
least two people should lift the Backpacker into the rear of the vehicle.
WARNING! Avoid pinch points! Do not hold the lift frame by the pivot points when installing
the Backpacker.
13. Placea lockingplate overeachofthethreadedholesinthefloorplateandsecurewiththesuppliedbolts.Screw
thebolts intothe threadedholes,but donot fullytightenthe hardwareatthis time.See figure2.
TOWER MICROSWITCHES
STOP BLOCK
LOCKING PLATE TRUCK MICROSWITCH
TRUCK
FRAME

10 www.pridemobility.com Backpacker
III. INSTALLATION
14. Simultaneouslypress thetwomicroswitches on the
Backpacker tower arm and the “DOWN” button
on the hand control until thetower reaches its full
extension.Seefigure2.
15. Releasethemicroswitches,thenpress the “UP” but-
ton on the hand control toretract the towerarm.
16. Insert the T-Bar into the lift tower and secure into
positionwiththesupplied hardware.See figure3.
17. Pushthe “UP”buttononthehand controltoraise the
platformframetoitshighestposition.
18. Inspect the clearance between the bumper and the
platformframe.Appropriateclearanceisnecessaryin
ordertoslidetheplatformintothevehicle.
NOTE: If there is not adequate clearance between
the bumper and the platform frame, you may need
to install an end support bracket. Remove the Back-
packer from the van and install the end support
bracket close to the rear door opening. Reinstall the
lift into the van, making sure that the bolts protrud-
ing from the bottom plate of the Backpacker closest
to the van door snap into the tapped holes on the
top of the end support bracket, then repeat steps 13
through 18.
NOTE: It may be required to trim the rear inside
sill to achieve the adequate platform clearance with
the platform under load.
19. Attachthe liftplatformto thelift frame. Referto the
installationinstructionssuppliedwithyourliftplatform.
20. Drape theY-strap over the platform and secure the
lockassemblytotheliftplatform.Seefigure4.
21. Fullytightenallmountinghardwarethroughoutthelift
system once the unit has been centered and all re-
quiredclearances havebeen achieved.
22. RuntheBackpackerthroughanentireliftcycle.Lower
theplatformtothegroundandthenraisetheplatform
to the fully stowed position in the van. See IV.
“Operation.” Figure 4.Y-Strap Installation
LOCK ASSEMBLY
Figure 3.T-Bar Installation
T-BAR
LIFT TOWER
NOTE: Pay attention to the path of the lift platform during operation. Make sure the lift does not rub
against or interfere with the vehicle in any way. If you notice any contact between the lift platform and
the vehicle, stop lift operation immediately and contact your authorized Pride Provider for assistance.

Backpacker www.pridemobility.com 11
III. INSTALLATION
WARNING! Release the “DOWN” button when the lift platform touches the ground. Do not
allow the motor to run after the lift platform has touched the ground. Allowing the motor to
run will increase the pressure on the lift platform and may result in product or vehicle
damage.
Wiring Harness Installation
Thewiringharnessisapproximately 25ft. (7.62meters)longandwill accommodatemost vehicles.
NOTE: You may wish to perform a practice run before installing the wiring harness. Route a piece of
light rope (equivalent to the gage of the wiring harness) along the anticipated path observing contact
points, potential rubbing/chafing points, and any sharp edges. Remove sharp edges with a fine grade
file, then treat the steel with a rust inhibitor or metal sealant.
Followthese steps to routethe Backpackerwiring harness:
1. Route theliftsystemwiringharness (startingat thelift)throughtheinterior ofthe vehicleuntilyou reachthe
vehiclebattery.Seefigure5.
WARNING! Avoid routing the wire harness where it will interfere with or become pinched
by the securement system floor plates.
2. Conceal the harnessbehindor under the interior panels (thereshouldbe existing holes). Be certain thatthe
harness is protected with a rubber grommet when passing it through the metal panels and into the engine
compartment.
3. Insidetheenginecompartment,securetheharnesstothefirewallandtheinnerfenderwithplasticwireties.Use
carenottocause abrasionsto thewiring harness.It isimportant tosecure thewiring harnessat variouspoints
alongitsrunof thevehicle.
WARNING! Do not cut or shorten the wiring harness. If the harness is too long, coil the
excess wire and secure it with plastic wire ties.
4. Remove the15-amp fusefromthewiringharness. Seefigure 5.
5. Connect the redwireto the positive (+)terminaland the black (grounding)wire to the negative(-)terminal
ofthevehicle battery.
Figure 5.Wiring Harness Installation
VEHICLE BATTERY
WIRINGHARNESS
HAND CONTROL
LIFT WIRING CONNECTION
FUSE
GROUNDINGWIRE

12 www.pridemobility.com Backpacker
III. INSTALLATION
Figure 6. Onboard Battery Installation
PROTRUDING BOLTS
6. Reinstallthe15-ampfuse tothe wiringharness.
WARNING! Before operating the lift,
inspect the wiring harness for proper
routing and grounding. Improper
routing can cause damage to the
harness, and improper grounding can
cause damage to the electrical
system.
Onboard Battery Installation
Theoptionalonboardbatteryisdesignedforeasyinstallation
as it does not require any wires to be routed through or
underthevehicle.
Followthesesteps to install the onboardbattery:
1. Remove the rubbercapsand nuts from the protrud-
ing bolts on the side of the lift motor housing. See
figure6.
2. Mount thebattery caseonto theprotruding boltsand
secureinto positionwiththenutsremovedearlier.See
figure6.
3. Inserttheonboardbatteryintothebatterycase,making
surethattheconnector on the bottom of the battery
alignsand fullyconnectswith thematingconnector
insidethe batterycase.
4. Connect the male connector on the battery cable
to the female connector at the base of the Back-
packer.
5. Secure the battery cable to the other cables with
wireties.

Backpacker www.pridemobility.com 13
IV. OPERATION
BACKPACKER LIFT SYSTEM OPERATION
The Backpacker Lift System is designed to lift an unoccupied mobility device from the ground and into the
cargoarea of afull-sized or minivanfor thepurposeof easy transport.
WARNING! The Backpacker Lift System is intended for the transport of unoccupied mobility
devices only. Do not sit on mobility device while activating lift or during transport.
Followthesesteps to load amobilitydevicewiththe
BackpackerLiftSystem:
1. Press and hold the “DOWN” button. See figure 7.
The lift will move out of the van to its farthest
forward stop, then lower to the ground. Once the
platform has reached the ground, release the
“DOWN” button.
NOTE: The lift motor is equipped with a slip clutch,
which emits a ratcheting noise at the end of each
horizontal (in and out) movement. This sound is
normal and does not indicate a problem with your
lift system.
2. Set the speed control to the slowest setting and
carefullydrive themobilitydevice ontothelift plat-
form,being sureto centerthe mobilitydevice onthe
platformtothebestofyourability.
NOTE: You may wish to load the mobility device
whilestandingnexttoit using the manualfreewheel
feature.Referto the mobility device owner’smanual
for more information on manual freewheel mode.
3. Shutdownthe powertothemobilitydevice, remove
the key if applicable, and make sure the unit is in
drive mode (drive motors engaged). Refer to the
mobility device owner’s manual for more
information on drive mode.
WARNING! Never leave a mobility
device in freewheel mode during lift
system transport. The mobility device
could roll, resulting in personal injury
and product damage.
4. Secure the mobility device to the platform by
draping theY-strap over the seat and buckling the
strapsecurely. See figure8.
Figure 7. Hand Control
Figure 8.Y-Strap Positioning

14 www.pridemobility.com Backpacker
IV. OPERATION
WARNING! Prevent product damage! Never attempt to secure the Y-strap over the seatback
or armrests of the mobility device.
5. Pull the end of the strap tightly to remove any excess slack over the seat.
NOTE: Inspect the Y-strap before each use to ensure there are no signs of fraying or wear. Ensure that
the mobility device is secured properly before transport. Pride is not liable for damage or loss resulting
from improper securing of a mobility device.
6. Pressandholdthe“UP”button.Seefigure7.Theliftwillmoveuptoitshighestliftpoint,thenslideintothevan.
Oncethemobilitydeviceis stowedcompletely withinthe van,releasethebutton.
NOTE: Make sure that the van has enough headroom to accommodate the height of the mobility device
before loading it into the van. Lower the tiller, adjust the seatback angle, or remove the seat if necessary.
Refer to the mobility device owner’s manual for more information on these adjustments.
WARNING! Prevent vehicle damage! Do not exceed the load limits of your vehicle as
specified by the vehicle manufacturer.
WARNING! Do not sit on your mobility device while it is in a moving vehicle. Personal
injury and/or property damage may result.
Whenyou are readytoremove the mobilitydevicefrom the van,lowerthe platform totheground, unfasten the
Y-strap, and drive the mobilitydeviceoffof the platform. Once unloading is complete, return theliftplatform
intothe van.

Backpacker www.pridemobility.com 15
BATTERY CHARGING
Followthesesteps to charge theonboard battery:
1. Remove theonboardbattery from thebatterycase andplaceit near astandardelectrical wall outlet.
2. Remove thecapfrom the chargersocketlocated on thebottomof thebattery, plug the charger cord into the
chargersocket,thenconnect the chargercordto a standard electricaloutlet.See figure 9.
PROHIBITED! Never use an extension cord to plug in your charger cord. Plug the charger
cord directly into a properly wired standard wall outlet.
PROHIBITED! Removal of the grounding prong can create an electrical hazard. If necessary,
properly install an approved 3-pronged adapter to an electrical outlet having 2-pronged
plug access. Failure to heed could result in personal injury and/or property damage.
WARNING! Prevent component damage! Do not attempt to charge the battery and operate
the lift system at the same time.
WARNING! Prevent component damage! Do not attempt to wire the lift system directly to
the vehicle battery if the lift system is equipped with an onboard battery.
NOTE: It is recommended that you replace the battery every 3–5 years. Store the battery in a
moisture-free environment when not in use.
V. BATTERY CHARGING
Figure 9. Battery Charging
CHARGERSOCKETANDCAP
MAINCIRCUITBREAKER
WORKINGFUSE BLOWNFUSE(REPLACE)
Figure 10. Fuse Replacement
Charger Circuit Fuse
Thebatterychargercordisequippedwith a7.5Acharger
circuitfuse. Intheevent thefuse shouldceaseto work:
1. Remove the cap from the fuse holder, then pull the
fuseout ofits slot.
2. Examinethefusetobesureitisblown.Seefigure10.
3. Insert anewfuse ofthe same rating.
WARNING! The replacement fuse
must exactly match the rating of the
fuse being replaced. Failure to use
properly rated fuses may cause
damage to the electrical system and
may result in personal injury.
Main Circuit Breaker
Themaincircuitbreakerisasafetyfeature builtintoyour
liftsystembattery.Whenthebatteryand/ormotorisheavily
strained (e.g., from excessive loads), the main circuit
breaker trips to prevent damage to the motor and the
electronics.Ifthecircuittrips,allowtheliftsystemto“rest”
forapproximately one minute. Then,pushin the circuit
breakerbuttonandcontinuenormaloperation.Ifthemain
circuitbreaker continuesto triprepeatedly,contact your
authorizedPrideProvider.

16 www.pridemobility.com Backpacker
VI. CARE AND MAINTENANCE
CARE AND MAINTENANCE
Your lift system requires a minimal amount of care and maintenance. If you do not feel confident in your
ability to perform the maintenance listed below, you may schedule inspection and maintenance at your
authorized Pride Provider. The following areas require periodic inspection and/or care and maintenance.
90-Day Maintenance Schedule
Every 90 days, remove the battery connections and clean them to ensure uninterrupted electronic connec-
tion and grease these pivot points:
!Main screw
!Pivot
Wiring Harness and Hand Control
!Thewiringharness shouldbe checkedperiodicallyforcorrosionand/or decay.ContactyourauthorizedPride
Providerif thewiringharness needstobe replaced.
!Avoidleavingthehandcontrolinareaswhereitwillbeexposedtoinclementweatherortemperatureextremes.
Exposureto theelementsmay causedamageto thehandcontrol.
Lift Platform/Metal Components
!Checkthelift platformforwearordamage.Contactyourauthorized PrideProviderforrepairor replacement.
!Theliftplatformsurface maybecome slipperyif exposedto moisture(ice, snow,rain,mist/sprayconditions,
etc.). Use caution when loading/unloading a mobility device in these conditions and wipe off any excess
moisturefromtheliftplatform.
!Regularlyinspectthemetalliftcomponentsforscratches.Treatanyproblemareaswitharustinhibitorormetal
sealant.
Battery Replacement
WARNING! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wash hands after handling.
Followthesesteps to replacethe onboard battery (figure 11):
1. Unfasten thebatterysecurement strap locatedatthe bottom of thebattery box.
2. Remove thehardwarefrom the batterysecurementbracket and removethebracket.
3. Remove thehardwarefrom thebattery connector.
4. Slide the batteryoutof the battery box to exposethebattery harness.
5. Disconnect thebattery harnessesfrom thebatteryterminals.
6. Connect the batteryharnessesto the new battery.
7. Slide thenewbattery into thebattery box.
8. Reinstall thehardwaretosecurethe batteryconnector andtighten.
9. Reinstall thebattery securementbracket andtighten thehardware.
10. Refastenthe batterysecurement strap.
Ifyourliftsystemisexhibitingwearthatyoufeelisquestionableinanyway,contactyourauthorizedPrideProvider
immediately. Donot attempttorepair,adjust,ormodify themanufacturer settingsandmaterials.

Backpacker www.pridemobility.com 17
VI. CARE AND MAINTENANCE
Figure 11. Battery Replacement
BATTERY SECUREMENT STRAP
BATTERY SECUREMENT BRACKET BATTERY CONNECTOR
BATTERY BOX

18 www.pridemobility.com Backpacker
VII. TROUBLESHOOTING
TROUBLESHOOTING
Any electromechanical device occasionally requires some troubleshooting. However, most of the prob-
lems that may arise can usually be solved with a bit of thought and common sense. Many of these problems
occur because the batteries are not fully charged or because the batteries are worn down and can no longer
hold a charge.
Whatifthemotoronmy lift system will not operate?
!Makesure theonboardbattery orvehiclebattery isfully charged.
!Makesure all connections to themotorand battery are secure.
!Checkthe wiringharnessfor signs ofwear or decay.Replacethe harnessifnecessary.
Whatifthelift system operates slowly upor down?
!Makesure theonboardbattery orvehiclebattery isfully charged.
!Makesure all connections to themotorand battery are secure.
!Checkthe wiringharnessfor signs ofwear or decay.Replacethe harnessifnecessary.
Whatiftheliftplatformdoesnotlowercompletelytotheground?
Checkto makesurethat thearea under thelift platformisfree fromobstructions.

Backpacker www.pridemobility.com 19
VIII. SPECIFICATIONS
SPECIFICATIONS
LiftSystemDimensions Overall Length:46in.(117cm)
OverallWidth(includingplatform):47in.(119.4cm)
OverallHeight:38in.(96.5cm)
PlatformLength:47in.(119.4cm)
PlatformWidth:27 in.(68.6 cm)
TotalLiftSystemWeight 155 lbs.(70 kg)including standardplatform
BaseLiftWeight 98 lbs. (44.5 kg)
MaximumLiftCapacity 325 lbs. (147 kg)
MobilityDeviceDimensions Length: 47in.(119.4cm)*
Height:34 in.(86.4 cm)*
Width 26 in. (66 cm)
MaximumLiftTravelDistance 26 in.(66 cm)vanfloor to ground
Motor Fullysealed, 12-voltDC
OnboardBattery 12-volt, 18AH
Charger 110-volt, off-board
*Dependingonvehicledimensions.

20 www.pridemobility.com Backpacker
IX. WARRANTY
THREE-YEAR TRANSFERABLE LIMITED WARRANTY
Forthree (3)yearsfrom thedate ofpurchase,Pride MobilityProducts willrepairor replaceatour option,free of
charge,anymechanical orelectricalcomponent founduponexamination byanauthorizedrepresentativeofPride
tobedefectiveinmaterial and/orworkmanship.
Thiswarranty doesnotextend tothoseitems, whichmayrequire replacementdue to normalwear and tear.
!Labor,servicecalls, shipping,and otherchargesincurred forrepair ofthe product,unlessspecifically autho-
rizedby Pride MobilityProductsCorporation INADVANCE,are excluded.
Exclusionsalsoincludecomponentswithdamagecausedby:
!Contamination
!Abuse,misuse,accident, ornegligence
!Batteryfluidspillageorleakage
!Commercialuse,oruseotherthannormal
!Improperoperation, maintenance,or storage
!Repairsand/ormodifications madetoanypartwithout specificconsentfromPrideMobility ProductsCorpo-
ration.
!Circumstancesbeyond thecontrol ofPride
ONE-YEAR WARRANTY
Thebatteryis covered by aseparateone(1) year warranty provided bythebattery manufacturer. Thebatteries
arenot warranted byPrideMobility ProductsCorporation.
SERVICE CHECKS AND WARRANTY SERVICE
AnauthorizedPrideMobilityProductsProvidermustperformwarrantyservice.DonotreturnfaultypartstoPride
MobilityProductswithoutpriorwrittenauthorization.Alltransportationcostsandshippingdamageincurredwhile
submittingpartsforrepairor replacementis theresponsibilityofthepurchaser.
Failureto followthe instructions,warnings,and notesin theowner’s manualand thoselocatedonyourPride lift
productcan resultin personalinjuryor productdamage andwillvoid Pride’s productwarranty.
Thereis no otherexpress warranty.
IMPLIED WARRANTIES
Impliedwarranties, includingthose ofmerchantabilityand fitnessfor aparticularpurpose, arelimited toone(1)
yearfrom the date ofpurchaseand to the extentpermittedby law.Anyandall implied warranties areexcluded.
Thisisthe exclusiveremedy.Liabilitiesforconsequentialdamagesunderanyandallwarranties areexcluded.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion of
limitationincidentalorconsequential damages.Theabovelimitationorexclusionmaynotapplytoyou.
Thiswarrantygivesyouspecificrights,andyoumayalsohaveotherrights,whichvary fromstate tostate.
PleasefilloutandreturntheproductregistrationcardtoPrideMobilityProducts.Thiswill aidPride inproviding
thebest possibletechnical andcustomer service.