ProFusion GD8110BP-M User manual

INFRARED ZONE HEATING SYSTEMTOWER
HEATER
OWNER’S MANUAL
Model No. GD8110BP-M
Formatted: Centered

2
Technical support: 1-866-206-0888
Service email: [e-mail]
PLEASE SAVE THESE INSTRUCTIONS
WARNING: READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE.
Thank you for choosing a RD-WORKSPROFUSION HEAT Infrared Zone Heating System. This
owner’s manual will provide you with valuable information necessary for the proper care and
maintenance of your new product. Please take a few moments to thoroughly read the instructions
and familiarize yourself with all the operational aspects of your new heater.
IMPORTANT INSTRUCTIONS
When using this electric unit, basic safety precautions should always be followed to reduce the
risk of fire, electric shock, and injury to persons, including the following:
1. Read ALL instructions before using this unit.
2. CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself.
3. This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot
surfaces. If provided, use handles when moving this heater.
4. Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and
curtains at least 3 ft from the front of the heater and keep them away from the sides, top,
and rear. DO NOT place towels or other objects on the heater.
5. Extreme caution is necessary when any heater is used by or near children or the disabled,
or when the heater is left operating and unattended.
6. DO NOT operate any heater with a damaged cord or after the heater malfunctions, has
been dropped or damaged in any manner. Return heater to authorized service facility for
examination, electrical or mechanical adjustment, or repair.
7. This heater is not intended for use in bathrooms, laundry areas and similar indoor
locations. NEVER locate heater where it may fall into a bathtub or other water container.
To protect against electrical hazards, DO NOT immerse in water or other liquids.
8. DO NOT touch the control panel or plug with a wet hand.
9. DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or
similar coverings. Arrange cord away from traffic area and where it will not be tripped
over.
Formatted: Font: 16 pt
Formatted: Font: 14 pt
Formatted: Font: 16 pt
Formatted: Font: 14 pt
Formatted: Font: 16 pt

3
10. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as
this may cause an electric shock or fire, or damage to the heater.
11. To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner. DO
NOT use on soft surfaces, like a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside. DO NOT use in areas where
gasoline, paint, explosive and/or flammable liquids are used or stored. Keep unit away
from heated surfaces and open flames.
13. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension
cord or relocatable power tap (outlet/power strip).
14. To avoid fire or shock hazard, plug the unit directly into a 120 V AC electrical outlet.
15. To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull firmly on
the plug, DO NOT unplug by pulling on the cord.
16. Always unplug the unit before moving or cleaning, or whenever the heater is not in use.
17. Use only for intended household use as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or injury to persons.
The use of attachments not recommended or sold by unauthorized dealers may cause
hazards.
18. Always use on a dry, level surface. Use on floor only.
19. DO NOT use outdoors.
20. WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit with any
solid-state speed control device.
21. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit.
Doing so will void your warranty. The inside of the unit contains no user serviceable
parts. Qualified personnel should perform all servicing only.
22. Connect to properly grounded outlets only.
23. Save these instructions.
23.
SPECIFICATIONS
Voltage Rating 120 V (60Hz)
Power Consumption 1000W
Unit Size 7.1 in. (W) ×7.1 in. (D) ×18.3 in. (H)
Unit Weight 6.2 lbs
Formatted: No bullets or numbering
Formatted: Font color: Auto
Formatted: Font color: Auto
Formatted: Font color: Auto
Formatted: Font color: Auto
Formatted: Font color: Auto

4
SAFETY FEATURES
Tip-Over Safety Feature
This heater is equipped with a tip-over safety feature. Once the heater is tipped over, an internal
switch will automatically shut the heater off. When the heater is restored to normal upright
position, the heater will reset. To continue operation, turn on the heater using the supplied remote
control or the control panel on the heater.
Overheat Safety Feature
This heater is equipped with a overheat safety feature. When the heaters internal components
reach a certain temperature that could cause overheat and possible fire, the heater will
automatically shut off. If occurs, unplug it, inspect and remove any objects on or adjacent to the
heater that may cause high temperatures. Wait five to ten minutes for the unit to cool down, then
plug it back it, and resume the normal operation.
WARNING: This heater has a voltage rating
of 120 volts. The cord has a plug as shown in
A. An adapter as shown in C is available for
connecting three-blade grounding-type plugs to
two-slot receptacles. The grounding lug
extending from the adapter must be connected
to a permanent ground such as a properly
grounded outlet box. The adapter should not be
used if a three-slot grounded receptacle is
available.
DO NOT DEFEAT THE SAFETY PURPOSE
OF THE GROUNDED PLUG.
WARNING: It is normal for the power cord to feel warm to the touch; however, a loose fit
between the outlet and the plug may cause overheating of the plug. If this occurs, try inserting
the plug into a different outlet. Contact a qualified electrician to inspect the original outlet for
damage.
IN THE BOX
·INFRARED ZONE HEATING SYSTEMHEATER
·REMOTE CONTROL (2 AAA batteries, not iIncluded)
·INSTRUCTION BOOKLET
PRODUCT DIAGRAM
Air O
utlet
Control Panel
Air Intake

5
1. OFF: switch to OFF position to turn the heater off.
2. Fan only setting
3. Low heat setting
4. High heat setting
5. Oscillation control button
6. Selector switch
7. Indicator lamp.
CONTROL PANEL
Formatted: Font: 18 pt

6
1)The unit
OPENING INSTRUCTIONS
1. Carefully remove the heater from carton and the bag. Make certain the unit is in the OFF
position before plugging the heater into the power outlet.
2. Before using the heater, make sure that it is on a flat and stable surface. Damage may occur if
it is placed in an incline or decline.
3. Turn off all the controls of the heater, and then plug the heater power cord directly into a
standard grounded AC outlet. Be sure plug fits tightly into outlet.
4. Set the selector switch to desired position. Use High setting to raise the temperature quickly.
Once the room is comfortable, select a lower power setting to prevent the room from becoming
too warm.
5. This model is equipped with an oscillation feature. If you want to obtain a wider area of heat
circulation, press button for oscillation function.
6. To completely shut the heater off, turn all the controls to OFF, and remove plug from the
socket-outlet.
Power light remains on when the heater power supply cord is plugged into an electrical outlet
and operated well.
This unit has FAN only setting which helps you to cool down the unit before you turn it off.
MAINTENANCE
1. Turn the selector switch to OFF position.
2. Unplug the unit and let it cool completely.
3. To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You
may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth.
CAUTION: DO NOT let liquid enter the heater.
4. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to
clean the heater. This may cause damage or deterioration to the surface of the heater.
5. DO NOT immerse the heater in water.
6. Wait until the unit is completely dry before use.
7. Air filter needs cleaning after used 3 months of use. Please take off the filter with the 2
steps in the drawing below. Flush and clean the filter with water, then dry it out and re-
assemble.
2) Remove Air filter

7
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the
original packaging to repack the unit.
BASIC TROUBLESHOOTING
If the heater will not operate, please check the following before seeking repair advice. For
repairs, contact a Certified Electrician.
:
Problem
Probable Cause
Solution
Heater will not power on
Heater is not plugged into a
120 V polarized
outlet/receptacle.
Ensure unit is in OFF position. Plug in unit
and attempt to turn on again.
Thermal Fuse has
permanently disabled the
unit's fuse due to extreme
heat.
Do not attempt to fix heater yourself.
Contact customer service for repair
information.
Breaker/Fuse has been
tripped.
Please check your electrical box to
confirm the breaker has not been blown.
This may occur if the unit is sharing a
receptacle with another high power
consuming appliance. Ensure unit is in
OFF position. Plug in unit and attempt to
turn on again.
Attempt to plug unit into another
independent output in the house.
The heater is creating
a burning smell.
A drop of oil fell on the
heating coil during the
manufacturing process. It
will quickly evaporate and
should not occur again.
Ensure room in which heater is situated is
well ventilated.
Check & ensure there are
no combustible materials
within 3' (0.9 m) of the heater.
Remove the combustible units preventing
air intake into the heater.
Formatted Table