ProFusion Salamander PS-10241P User manual

1
Salamamder Heater With Cart
OWNER’S MANUAL
PS-10241P 10KW 240V 60Hz 1P
PS-15243 15KW 240V 60Hz 3P
PS-15203 15KW 208V 60Hz 3P
PS-30483 30KW 480V 60Hz 3P
IMPORTANT INSTRUCTIONS
READ & SAVE
Technical support: 1-866-206-0888
Service email: [e-mail]

2
TABLE OF CONTENTS
Important Instructions………………………………………..3-4
Specifications and Wiring Diagram………………………. .5-9
Parts of the heater ……………………….……………………10
Installing Instructions……………………….…………..…….11-12
Operating Instructions……………………….………....……..13
Maintenance and Cleaning……………………………………14
Warranty Information ………………………………………….14
ARRANTY INFORMATION

3
IMPORTANT INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS HEATER
NOTE: There may be a trace of smoke or odor when unit is first
operated. Don’t be alarmed. This indicates that a drop of oil fell on
the heating coil during the manufacturing process. It will quickly
evaporate and should not re-occur.
Make sure that the room in which the appliance is located is well
ventilated during this operation. It is normal for the appliance to
emit small cracking sounds when you turn it on for the first time. Do
not be alarmed.
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED TO REDUCE RISK OF FIRE,
ELECTRICAL SHOCK AND INJURY TO PERSONS OR PROPERTY,
INCLUDING THE FOLLOWING:
1) Read all instructions before using this heater.
2) This heater is hot when in use. To avoid burns, do not let bare skin
touch hot surfaces. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at least 3’ (0.9 m) from the
front of the heater and keep them away from the sides and rear.
3) Extreme caution is necessary when any heater is used by or near
children or invalids and whenever the heater is left operating and
unattended.
4) Always switch off the heater when not in use.
5) Do not operate any heater after the heater malfunctions, has been
dropped or damaged in any manner. Disconnect power at service panel
and have heater inspected by a reputable electrician before reusing.
6) Do not use outdoors.
7) To disconnect heater, turn off power to heater circuit at main
disconnect panel.
8) Do not install less than 6 feet (1.8m) high from the floor and keep the
mounting bracket not less than 4 feet (1.2m) away from any adjacent
vertical surface. Keep at least 4.5 inches (11.5cm) from the back wall
(with or without using the wall hanging mounting bracket).

4
9) For floor standing by the cart, position it at a level floor; keep at least
4 feet (1.2m) from any adjacent vertical surface or walls. Keep at least 1
foot (0.3m) from the back wall.
10) Do not insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock or fire, or damage
the heater.
11) To prevent a possible fire, do not block air intakes or exhaust in any
manner.
12) A heater has hot and arcing or sparking parts inside. To reduce the
risk of fire, do not use it in areas where gasoline, paint, or flammable
vapors and liquids are used or stored.
13) Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or
injury to persons.
14) This product must be installed by a certified electrician, in accordance
with local codes.
15) Avoid the use of an extension cord because the extension cord may
overheat and cause a risk of fire.
16) This heater is not intended for use in bathrooms, laundry areas and
similar indoor locations. Never locate heater where it may fall into a
bathtub or other water container.
CAUTION –High temperature, risk of fire, keep electrical cords,
drapery, furnishings, and other combustibles at least 3 feet (0.9 m)
from the front of the heater and away from the side and rear.
PET OWNERS WARNING:
The health of some small pets including birds are extremely sensitive
to the fumes produced during the first-time use of many appliances.
These fumes are not harmful to humans but we recommended that
you do not use your heater around birds and small pets during its
initial use until the manufacturing corrosion coatings burn off.
SAVE THESE INSTRUCTIONS

5
Salamander Heater with cart
Model: PS-10241
MANUFACTURER No.: PS-10241P
Volt: 240 V, 1P
Watts: 10KW
Frequency: 60 Hz
Wiring diagram:
SPECIFICATIONS

6
Model: PS-15243
MANUFACTURER No.: PS-15243
Volt: 240 V, 3P
Watts: 15KW
Frequency: 60 Hz
Wiring diagram:

7
Model: PS-15203
MANUFACTURER No.: PS-15203
Volt: 208 V, 3P
Watts: 15KW
Frequency: 60 Hz
Wiring diagram:

8
Model: PS-30483
MANUFACTURER No.: PS-30483
Volt: 480 V, 3P
Watts: 30KW
Frequency: 60 Hz
Wiring diagram:

9
Wiring Instruction
For 3 Phase Model: PS-30483
Open the cover.
After connection.
Earth Wire
L2 (Live Wire2
Black)
L3 (Live Wire3
Red)
L1 (Live Wire1
White)

10
A. Handle
B. Heater Housing
C. Tilt adjustable knob
D. Wheel
E. Front Grill
F. ON/OFF Switch
G. Temperature Setting Knob
PARTS OF THE HEATER
A
D
E
G
F
B
C

11
WARNING: All wiring must be installed by a certified electrician
according to the electrical safety.
The heater must be grounded in accordance with all national and local
building codes.
All wiring procedures and connections shall be in accordance with
the national and local codes having jurisdiction.
Before installation:
Disconnect the main supply connection.
The heater must be connected to individual branch circuit protected by 65
Amp circuit breaker only.
Supply cables must be equipped with a dual pole circuit breaker rating at
least 240V 65A/pole as main cutoff switch of power connection to the
heater.
CAUTION: High temperature, risk of fire, keep electrical cords, drapery,
furnishings, and other combustibles at least 3 feet (0.9 m) from the front
of the heater and away from the side and rear.
WARNING: To reduce the risk of fire, do not store or use gasoline or
other flammable vapors and liquids in the vicinity of the heater.
INSTALLING INSTRUCTIONS

12
INSTALLATION INSTRUCTION:
1. Open the package, take out the heater.
2. Loosen the four screws in the handle, move the handle to the upper of
the cart stand.
3 Align the screw holes on the handle to the cart stand, re-insert the
four screws and tighten.
.
4. Run the electrical power supply cable in flexible conduit and connect
to the wiring compartment
5. Make the connections properly with connectors which are suitable for
the conductor size, in cluding grounding wirings. And after making the
connections, arrange the pigtail leads of unit and power supply wires in
the wiring compartment.

13
WARNING - The heater must be properly installed before it is
used.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC
FLASH :
Apply appropriate personal protective equipment (PPE) and
follow safe electrical work practices. See NFPA 70E.
A circuit breaker must be installed and serviced only by
qualified electrical personnel.
Always use a properly rated voltage sensing device to confirm
power is off.
Switch the ON/OFF switch to ON position to turn on the heater.
Then turn the thermostat to the farthest clockwise position. The fan
should start and the unit begins heating the room, and lamp is light.
After the room reaches comfort level, turn the thermostat
counterclockwise until the heater shuts off. The heater will
automatically cycle around this preset temperature. To increase the
temperature, turn the thermostat knob clockwise. To lower the
temperature, turn the thermostat counterclockwise.
Select a thermostat setting.
Ambient temperature is regulated by adjusting the thermostat to a
desired position. Allow theunit to operate and warmup the room. When
thedesired temperature is reached, turnthe control knob
counterclockwise until the heater turns off. This is your ideal setting. The
heater will start automatically when the room temperature drops below
this set point, and will turn off when the set point is reached.
To turn off the heater, switch the ON/OFF switch to OFF
position.
OPERATING INSTRUCTIONS

14
There is no user maintenance part except regular cleaning as following
description. All other servicing or maintenance should be performed by
qualified service personnel.
Before any cleaning, make sure that:
1. Disconnect power supply at source.
2. Wait for 60 minutes to ensure the heating element has cool down, and
your heater is now ready for cleaning.
Regular Cleaning:
1. Do not use cleaning liquid or other chemicals to spray on the unit.
2. Interior dust can often be removed by using a vacuum cleaner with a
crevice tool attachment.
3. To clean enclosure, use a clean, soft and lightly damp cloth to gently
wipe off the dirt from the surface of the unit. Be sure not to wet the
heating element and the switches. Allow the unit to dry completely
before using it.
CAUTION: DO NOT ALLOW WATER TO RUN INTO THE INTERIOR OF
THE HEATER AS THIS COULD CREATE A FIRE OR ELECTRIC
SHOCK HAZARD, DAMAGING THE UNIT.
This product carries a one (1) year warranty against defects in
workmanship and materials. Profusion Heat agrees to replace a defective
product, within the stated warranty period, when returned to the place of
purchase with proof of purchase. This product is not guaranteed against
wear or breakage due to misuse and/or abuse.
MAINTENCE AND CLEANING
INSTRUCTIONS(separate page)
WARRANTY INFORMATION