ProFusion PH-9100WN User manual

1
10,000W 240V Ceiling/Wall
Garage Heater
OWNER’S MANUAL
Model No.: PH-9100WN
10000W 240V 60Hz
7500W 208V 60Hz
IMPORTANT INSTRUCTIONS
READ & SAVE
Technical support: 1-866-206-0888
Service email: [e-mail]

2
TABLE OF CONTENTS
Important Instructions……………………………………… 3
Specifications and Wiring Diagram………………………. 5
Parts of the heater ……………………….………………… 6
Installing Instructions……………………….……………… 7-10
Operating Instructions……………………….………….... 11
Maintenance and Cleaning………………………………. 12
Troubleshooting……………………………………………. 13

3
IMPORTANT INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS
HEATER
NOTE: There may be a trace of smoke or odor when unit is first
operated. Don’t be alarmed. This indicates that a drop of oil fell on
the heating coil during the manufacturing process. It will quickly
evaporate and should not re-occur.
Make sure that the room in which the appliance is located is well
ventilated during this operation. It is normal for the appliance to emit
small cracking sounds when you turn it on for the first time. Do not
be alarmed.
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED TO REDUCE RISK OF FIRE,
ELECTRICAL SHOCK AND INJURY TO PERSONS OR PROPERTY,
INCLUDING THE FOLLOWING:
1) Read all instructions before using this heater.
2) This heater is hot when in use. To avoid burns, do not let bare skin touch
hot surfaces. Keep combustible materials, such as furniture, pillows, bedding,
papers, clothes, and curtains at least 3’ (0.9 m) from the front of the heater
and keep them away from the sides and rear.
3) Extreme caution is necessary when any heater is used by or near children
or invalids and whenever the heater is left operating and unattended.
4) Always switch off the heater when not in use.
5) Do not operate any heater after the heater malfunctions, has been
dropped or damaged in any manner. Disconnect power at service panel and
have heater inspected by a reputable electrician before reusing.
6) Do not use outdoors.
7) To disconnect heater, turn off power to heater circuit at main disconnect
panel.
8) Do not install less than 8 feet (2.4m) high from the floor and closer than 1
foot (0.3m) to any adjacent vertical surfaces or walls. Keep at least 4.5 inches
(11.5cm) from the back wall (with or without using the wall hanging mounting
bracket).
9) Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire, or damage the heater.
10) To prevent a possible fire, do not block air intakes or exhaust in any
manner.

4
11) A heater has hot and arcing or sparking parts inside. To reduce the risk of
fire, do not use it in areas where gasoline, paint, or flammable vapors and
liquids are used or stored.
12) Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or injury to
persons.
13) This product must be installed by a certified electrician, in accordance
with local codes.
14) For supply cables, use 6 AWG (13.3 mm2) copper wires .
15) WARNING –RISK OF FIRE, DO NOT USE AS A RESIDENTIAL OR
HOUSEHOLD HEATER.
CAUTION –High temperature, risk of fire, keep electrical cords, drapery,
furnishings, and other combustibles at least 3 feet (0.9 m) from the front of the
heater and away from the side and rear.
PET OWNERS WARNING:
The health of some small pets including birds are extremely
sensitive to the fumes produced during the first-time use of many
appliances. These fumes are not harmful to humans but we
recommended that you do not use your heater around birds and
small pets during its initial use until the manufacturing corrosion
coatings burn off.
SAVE THESE INSTRUCTIONS
WARNING –RISK OF FIRE, DO NOT USE AS A RESIDENTIAL OR
HOUSEHOLD HEATER.

5
10,000W 240V Ceiling/Wall Garage Heater
Model : PH-9100WN
Voltage : 1-Phase 208 / 240 V
Watts: 7500 / 10000 W
Frequency: 60 Hz
Recommended Heating Capacity: 1.25 watts / ft3 (0.03m3)
Wiring diagram:
SPECIFICATIONS

6
A. Wall Mount Bracket
B. Ceiling Bracket
C. Upper Housing
D. Louver for air direction
E. Tilt adjustable knob
F. Down Housing
G. Front Exhaust Grill
H. ON/OFF Switch
PARTS OF THE HEATER
A
E
B
C
D
F
G
H

7
WARNING:All wiring must be installed by a certified electrician
according to the electrical safety.
The ceiling heater must be grounded in accordance with all national
and local building codes.
All Wiring procedures and connections shall be in accordance
with the national and local codes having jurisdiction.
Before installation:
Disconnect the main supply connection.
Supply cables shall be 6 AWG (13.3 mm2) copper wires.
The heater must be connected to individual branch circuit protected
by 60 Amp circuit breaker only.
Supply cables must be equipped with a dual pole circuit breaker
rating at least 240V 40A/pole as main cutoff switch of power
connection to the heater.
Wiring compartment for accommodating supply cables and pigtail
leads are adequate and measured free space of 2524.67 cm3.
CAUTION : High temperature, risk of fire, keep electrical cords,
drapery, furnishings, and other combustibles at least 3 feet (0.9 m)
from the front of the heater and away from the side and rear.
WARNING: To reduce the risk of fire, do not store or use gasoline
or other flammable vapors and liquids in the vicinity of the heater.
INSTALLATION INSTRUCTION:
1. Keep the unit at least 8 feet (2.4m) away from the floor. This
minimum distance must be maintained.
2. Do not install closer than1 foot (or 0.3 m) to any adjacent vertical
surfaces or walls.
3. Keep at least 4.5 inches (11.5cm) from the back wall (with or
without using the wall hanging mounting bracket).
4. Mark the drill-hole positions on the wall or ceiling for the
mounting bracket.
INSTALLING INSTRUCTIONS

8
5. Drill the required holes with diameter fit for the anchor provided
for positioning the mounting bracket.
6. Insert the anchors.
7. Attach the mounting bracket to the wall and secure with
mounting screws.
8. Loose the tilt adjustment knobs, remove the cart.
9. Align the Hang Bracket to the knob screw holes.
10. Re-insert the knob and tighten.
11. Hook the unit to the mounting bracket and let the unit hang from
the mounting bracket.
12. Insert the bolt provided through the mounting bracket and the
heater handle; tighten with the nut and washer.
Wall Mount
Ceiling Mount

9
13. Loosen the screw to remove the small cover in the rear of the
heater.
14. Run the electrical power supply cable in conduit.
15. Secure the conduit to the back plate via the knock-out hole.
16. Make the connections properly with connectors which are
suitable for the conductor size, in cluding grounding wirings.
Pull all the conductors from the conduit. Strip 3/4 inch of
insulation from each of the insulated conductors. Make a right
angle bend in the white insulated pigtail and place its stripped
end next to the stripped ends of the other white supply cable.
Make sure that the bare ends are tight together and square.
Using lineman's pliers, twist the bare ends tightly together in a
clockwise direction, then screw one of the wire nuts tightly on the
spliced conductors. Check to be sure that no bare copper shows
from beneath the wire nut. Repeat these steps for the black
conductor. Once the wire nuts are firmly in place, cover them with
Wall Mount
Ceiling Mount

10
plastic electrical tape. The grounding conductor is spliced in the
same manner.
17. And after making the connections, arrange the pigtail leads of
unit and power supply wires in the wiring compartment.
18. Replace the wiring cover and lock in place with the screw.
19. Consult NEC code for other types of approved electrical wire
splices & wire connectors.

11
WARNING - The heater must be properly installed before it is
used.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR
ARC FLASH :
Apply appropriate personal protective equipment (PPE)
and follow safe electrical workpractices. See NFPA 70E.
A circuit breaker must be installed and serviced only by
qualified electrical personnel.
Always use a properly rated voltage sensing device to
confirm power is off.
The switch on the heater is to start the Fan and Heater.
Use the circuit breaker as power ON/OFF device. The
circuit breaker is to be installed by certified electrican
and shall be located in line of sight from the heater
location or shall be capable of being locked in open
position. Follow the operating instruction to reduce
the risk of fire, electric shock, injury or death to
persons.
Switch on the circuit breaker to turn on the heater power.
Press the switch at the back of the heater to turn on the fan
and heating function.
To turn off the heater, press the switch turn off the fan and
heating function. And then switch off the circuit breaker.
The circuit breaker serves as the power
disconnection means.
OPERATING INSTRUCTIONS

12
There is no user maintenance part except regular cleaning as
following description. All other servicing or maintenance should be
performed by qualified service personnel.
Before any cleaning, make sure that:
1. Disconnect power supply at source. Switch off the circuit
breaker.
2. Wait for 60 minutes to ensure the heating element has cool
down, and your heater is now ready for cleaning.
Regular Cleaning:
1. Do not use cleaning liquid or other chemicals to spray on the
unit.
2. Interior dust can often be removed by using a vacuum cleaner
with a crevice tool attachment.
3. To clean enclosure, use a clean, soft and lightly damp cloth to
gently wipe off the dirt from the surface of the unit. Be sure not
to wet the heating element and the switches. Allow the unit to
dry completely before using it.
CAUTION: DO NOT ALLOW WATER TO RUN INTO THE
INTERIOR OF THE HEATER AS THIS COULD CREATE A FIRE
OR ELECTRIC SHOCK HAZARD, DAMAGING THE UNIT.
MAINTENCE AND CLEANING
INSTRUCTIONS(separate page)

13
If your heater fails to operate, please follow these procedures:
This heater is intended to be a ceiling-mounted heater. It has a
thermal cut-off protection. If the thermal cut-off protection trips, then,
switch off the power. Switch off the circuit breaker.The unit
should reset automatically after 10 minutes. If the thermal cut-off
protection trips again, consult a certified electrician to determine the
reason for overheating.
Problem
Probable Cause
Solution
Unit is
not
heating.
Overheat protection has
temporarily deactivated the
heater.
Turn the heater OFF; Switch off
the circuit breaker.. Wait 10
minutes before turning on the
heater
Breaker/Fuse has been
tripped.
Check your electrical box to
confirm the breaker has not been
blown. This may occur if the
receptacle is shared between other
high consumption appliances.
The
heater is
producing
a burning
smell.
Check & ensure there are no
combustible materials within
0.9 meters (3 feet) surrounding
the heater.
Remove any combustible items
from the heater.
A drop of oil fell on the heating
coil during the manufacturing
process. It will quickly
evaporate and should not
occur again.
Ensure room in which heater is
situated is well ventilated.
Ensure a minimum clearance
of 4.5 inches (11.5 cm) from
both sides and rear of heater
to adjacent walls.
Reposition the heater so there is
enough space around the heater to
the adjacent walls.
PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HEATER
YOURSELF. DOING SO COULD CAUSE DAMAGE OR PERSONAL
INJURY.
TROUBLESHOOTING