ProFusion PH-960XNR User manual

1
7,500W/240V WALL / CEILING MOUNTED GARAGE HEATER
WITH ELECTRONIC CONTROLLER AND REMOTE
OWNER’S MANUAL
Model: PH-960XNR
IMPORTANT INSTRUCTIONS
READ & SAVE
PET OWNERS WARNING:
The health of some small pets including birds are extremely sensitive
to the fumes produced during the first-time use of many appliances.
These fumes are not harmful to humans but we recommended that
you do not use your heater around birds and small pets during its
initial use until the manufacturing corrosion coatings burn off.
Technical support: 1-866-206-0888
Service email: [e-mail]

2
TABLE OF CONTENTS
Important Instructions………………………………………. 3-4
Installation Instructions………………………. ……………..5-7
Specifications and Wiring Diagram …………………………8
Parts of the heater……………………….…………..…………9
Operating Instructions……………………….………....……10
Maintenance and Cleaning…………………………………12
Troubleshooting……………………………………………. 13

3
IMPORTANT INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS
HEATER
NOTE: There may be a trace of smoke or odor when unit is first
operated. Don’t be alarmed. This indicates that a drop of oil fell
on the heating coil during the manufacturing process. It will
quickly evaporate and should not re-occur.
Make sure that the room in which the appliance is located is well
ventilated during this operation. It is normal for the appliance to
emit small cracking sounds when you turn it on for the first
time. Do not be alarmed.
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED TO REDUCE RISK OF FIRE,
ELECTRICAL SHOCK AND INJURY TO PERSONS OR
PROPERTY, INCLUDING THE FOLLOWING:
1) Read all instructions before using this heater.
2) This heater is hot when in use. To avoid burns, do not let bare
skin touch hot surfaces. Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes, and curtains at least 3’
(0.9 m) from the front of the heater and keep them away from the
sides and rear.
3) Extreme caution is necessary when any heater is used by or near
children or invalids and whenever the heater is left operating and
unattended.
4) Always switch off the heater when not in use.
5) Do not operate any heater after the heater malfunctions, has been
dropped or damaged in any manner. Disconnect power at service
panel and have heater inspected by a reputable electrician before
reusing.
6) Do not use outdoors.
7) To disconnect heater, turn off power to heater circuit at main
disconnect panel.
8) Do not install less than 6 feet (1.8 m in U.S.A)/ 8 feet (2.4 m in
Canada) high from the floor and closer than 1 foot (0.3m) to any
adjacent vertical surfaces or walls. Keep at least 4.5 inches (11.5cm)

4
from the back wall (with or without using the wall hanging mounting
bracket).
9) Do not insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock or fire, or
damage the heater.
10) To prevent a possible fire, do not block air intakes or exhaust in
any manner.
11) A heater has hot and arcing or sparking parts inside. To reduce
the risk of fire, do not use it in areas where gasoline, paint, or
flammable vapors and liquids are used or stored.
12) Use this heater only as described in this manual. Any other use
not recommended by the manufacturer may cause fire, electric
shock, or injury to persons.
13) This product must be installed by a certified electrician, in
accordance with local codes.
14) For supply cables, use 8 AWG (8.3 mm2) copper wires.
15) This heater includes a visual alarm to warn that parts of the heater
are getting excessively hot. If the alarm flashes, immediately turn the
heater OFF and inspect for any objects, on or adjacent to the heater
that may have blocked the airflow or otherwise cause high
temperatures to have occurred.
DO NOT OPERATE THE HEATER WITH THE ALARM FLASHING.
To reset the heater, switch the CIRCUIT BREAKER OFF, and wait
five to ten minutes for the unit to cool down before turning the heater
on.
16）This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction regarding use of the appliance by a person
responsible for their safety. Children should be supervised to ensure
that they do not play with the appliance.
CAUTION –High temperature, risk of fire, keep electrical cords,
drapery, furnishings, and other combustibles at least 3 feet (0.9
m) from the front of the heater and away from the side and rear.
SAVE THESE INSTRUCTIONS

5
WARNING: All wiring must be installed by a certified electrician
according to the electrical safety.
The ceiling heater must be grounded in accordance with all national
and local building codes.
WARNING : To reduce the risk of fire, do not store or use gasoline or
other flammable vapors and liquids in the vicinity of the heater.
All Wiring procedures and connections shall be in accordance
with the national and local codes having jurisdiction.
NOTE: Compatible with a 240V Line Voltage Double Pole Wall
Thermostat. Must be installed by a Certified Electrician.
Before installation:
Disconnect the main supply connection.
Supply cables shall be 8 AWG (8.3 mm2) copper wires
The heater must be connected to individual branch circuit protected
by 40Amp circuit breaker only.
Supply cables must be equipped with a dual pole circuit breaker
rating at least 240V 40A/pole as main cutoff switch of power
connection to the heater.
CAUTION: High temperature, risk of fire, keep electrical cords,
drapery, furnishings, and other combustibles at least 3 feet (0.9 m)
from the front of the heater and away from the side and rear.
WARNING: To reduce the risk of fire, do not store or use gasoline
or other flammable vapors and liquids in the vicinity of the heater.
INSTALLATION INSTRUCTION:
1. Keep the unit at least 6 feet (1.8 m in U.S.A)/ 8 feet (2.4 m in
Canada) away from the floor. This minimum distance must be
maintained.
2. Do not install closer than1 foot (or 0.3 m) to any adjacent vertical
surfaces or walls.
3. Keep at least 4.5 inches (11.5cm) from the back wall (with or
INSTALLATION INSTRUCTIONS

6
without using the wall hanging mounting bracket).
4. Mark the drill-hole positions in the wall or ceiling for the mounting
bracket.
5. Drill the required holes with diameter fit for the anchor provided for
positioning the mounting bracket.
6. Insert the anchors.
7. Attach the mounting bracket to the wall or ceiling and secure with
mounting screws.
8. Hook the unit to the mounting bracket and let the unit hang from
the mounting bracket.
9. Insert the screw through the mounting bracket and the heater
handle, tighten the nut.
WALL MOUNT
CEILING MOUNT

7
10. Loosen the screw to remove the wiring compartment/connection
cover in the rear of the heater.
11. Run the electrical power supply cable in flexible conduit and
connect to the wiring compartment via the knock-out at back side of
the unit.
12. Make the connections properly with connectors which are
suitable for the conductor size, including grounding wirings. And after
making the connections, arrange the pigtail leads of unit and power
supply wires in the wiring compartment.
13 You can use the inside or wall thermostat. If you use the inside
thermostat, press the rock switch to INSIDE THERMOSTAT.
14 If you want to use the wall thermostat (Not included) , press the
rock switch to WALL THERMOSTAT, and insert the two wall
thermostat wire to the Terminal A inside the heater, make sure to
tighten the screws in the Terminal A.
15. Replace the wiring compartment/connection cover and lock in
place with the screw.

8
7,500W/240V WALL / CEILING MOUNTED GARAGE HEATER
WITH ELECTRONIC CONTROLLER AND REMOTE
Model: PH-960XNR
Volt: 240 V
Watts: 7500 W
Frequency: 60 Hz
BTU/h: 25597
Recommended Heating Capacity: 1.25 watts / ft³ (0.03m³)
Wiring diagram:
SPECIFICATIONS

9
A. Upper Enclosure
B. Tilt adjustable knob
C. Front Exhaust Grill
D. Louver for air direction
E. Control panel
F. Alarm LED
G. Power Indicator
H. Timer Indicator
I. Low Indicator
J. High Indicator
K. Inside/Wall Thermostat
Switch
L. ON/OFF Switch
PARTS OF THE HEATER
F
H
G
K
L
J
I
A
B
C
D
E
K
L

10
WARNING - The heater must be properly installed before it is
used.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC
FLASH:
Apply appropriate personal protective equipment (PPE) and
follow safe electrical work practices. See NFPA 70.
A circuit breaker must be installed and serviced only by
qualified electrical personnel.
Always use a properly rated voltage sensing device to
confirm power is off.
The Select switch on the heater is only for function
selection. Use circuit breaker as power ON/OFF device.
The circuit breaker is to be installed by a certified
electrician and shall be located in line of sight from the
heater location or shall be capable of being locked in
open position. Follow the operating instruction to
reduce the risk of fire, electric shock, injury or death to
persons.
Switch on the circuit breaker.
Insert the batteries to the remote controller as below images:
NOTE: Remove the batteries if the remote control is not to be used
for a month or more. Batteries left in the unit may leak and cause
damage.
DO NOT MIX OLD AND NEW BATTERIES! DO NOT MIX
ALKALINE, STANDARD (CARBON-ZINC) OR RECHARGEABLE
(NICKEL-CADMIUM) BATTERIES!
OPERATING INSTRUCTIONS

11
TURNING THE HEATER ON
To turn the heater ON, press the ON/OFF rock switch to ON
position, the power Indicator will turn on and display the room
temperature.
The factory setting temperature is 70℉, If you set the thermostat
switch to Inside Thermostat, and the room temperature is lower
or equal to 68℉, the heater will turn to High mode and will turn
off when the room temperature is higher or equal to 72℉.
SETTING THE TEMPERATURE
To set the desired temperature:
Press the + button until the numeric temperature starts flashing.
Press button again to increase the temperature or the –button to
decrease the temperature.
After setting the desired temperature, press the MODE button to
HIGH or LOW. The heater will run on HIGH or LOW heating
when the room temperature is equal to or lower than the setting
temperature - 2℉, and will turn off when the room temperature is
equal to or greater than the setting temperature+2℉.
Note: If you set the thermostat switch to WALL THERMOSTAT,
press the + and - button cannot set the temperature, the heater
will run in ON or OFF heating according the wall thermostat
setting temperature.
SETTING THE TIMER
Press the TIMER button until Set Time starts flashing. The
default value is 3 hours.
Press the “+” button to increase the set time or the “–” button to
decrease the set time. The timer can be set from 1 to 12 hours.
The timer will set and execute after the LED display stops
flashing. The heater will shut OFF automatically when the set
time is reached.
To turn the timer OFF, press the TIMER button, and then
pressing the “–” button to set the time to 0. The timer feature will
turn off when the LED stops flashing
.

12
To turn off the heater, switch off the circuit breaker.
The circuit breaker serves as the power
disconnection means.
This heater includes a visual alarm to warn that parts of the
heater are getting excessively hot. If the alarm flashes,
immediately turn the heater OFF and inspect for any objects, on
or adjacent to the heater that may cause high temperatures. DO
NOT OPERATE THE HEATER WITH THE ALARM FLASHING.
To reset the heater, switch the circuit breaker OFF, and wait five
to ten minutes for the unit to cool down before turning the heater
on.
There is no user maintenance part except regular cleaning as
following description. All other servicing or maintenance should be
performed by qualified service personnel.
Before any cleaning, make sure that:
1. Disconnect power supply at source. Switch off the circuit
breaker.
2. Wait for 60 minutes to ensure the heating element has cool down,
and your heater is now ready for cleaning.
Regular Cleaning:
1. Do not use cleaning liquid or other chemicals to spray on the unit.
2. Interior dust can often be removed by using a vacuum cleaner
with a crevice tool attachment.
3. To clean enclosure, use a clean, soft and lightly damp cloth to
gently wipe off the dirt from the surface of the unit. Be sure not to
wet the heating element and the switches. Allow the unit to dry
completely before using it.
CAUTION: DO NOT ALLOW WATER TO RUN INTO THE
INTERIOR OF THE HEATER AS THIS COULD CREATE A FIRE
OR ELECTRIC SHOCK HAZARD, DAMAGING THE UNIT.
MAINTENANCE AND CLEANING
INSTRUCTIONS(separate page)

13
If your heater fails to operate, please follow these procedures:
This heater is intended to be a ceiling-mounted heater. It has a
thermal cut-off protection. If the thermal cut-off protection trips, then,
switch off the power. Switch off the circuit breaker.The unit
should reset automatically after 10 minutes. If the thermal cut-off
protection trips again, consult a certified electrician to determine the
reason for overheating.
Problem
Probable Cause
Solution
Unit is
not
heating.
Overheat protection has
temporarily deactivated the
heater.
Turn the heater OFF; Switch
off the circuit breaker. Wait
10 minutes before turning on
the heater
Room temperature has been
warmed up to thermostat
setting.
To increase the room
temperature, adjust thermostat
control knob to a higher setting
Breaker/Fuse has been
tripped.
Check your electrical box to
confirm the breaker has not
been blown. This may occur if
the receptacle is shared
between other high
consumption appliances.
The
heater is
producing
a burning
smell.
Check & ensure there are no
combustible materials within
0.9 meters (3 feet)
surrounding the heater.
Remove any combustible
items from the heater.
A drop of oil fell on the
heating coil during the
manufacturing process. It will
quickly evaporate and should
not occur again.
Ensure room in which heater
is situated is well ventilated.
Ensure a minimum clearance
of 36 inches (90 cm) from
both sides and rear of heater
to adjacent walls.
Reposition the heater so there
is enough space around the
heater to the adjacent walls.
TROUBLESHOOTING

14
PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HEATER
YOURSELF. DOING SO COULD CAUSE DAMAGE OR
PERSONAL INJURY.