ProFusion PS-10241 User manual

1
Wall-Mounted Salamander Heater
OWNER’S MANUAL
PS-10241WP 10KW 240V 60Hz 1P
PS-30483W 30KW 480V 60Hz 3P
IMPORTANT INSTRUCTIONS
READ & SAVE
Technical support: 1-866-206-0888
Service email: [e-mail]

2
TABLE OF CONTENTS
Important Instructions………………………………………3-4
Specifications and Wiring Diagram………………………5-7
Parts of the heater ……………………….………………….8
Installing Instructions……………………….…………..….9-11
Operating Instructions……………………….………....…..12
Maintenance and Cleaning…………………………………13
Warranty Information ……………………………………….13

3
IMPORTANT INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS
HEATER
NOTE: There may be a trace of smoke or odor when unit is first
operated. Don’t be alarmed. This indicates that a drop of oil
fell on the heating coil during the manufacturing process. It will
quickly evaporate and should not re-occur.
Make sure that the room in which the appliance is located is
well ventilated during this operation. It is normal for the
appliance to emit small cracking sounds when you turn it on
for the first time. Do not be alarmed.
WHEN USING ELECTRICAL APPLIANCES, BASIC
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
REDUCE RISK OF FIRE, ELECTRICAL SHOCK AND INJURY TO
PERSONS OR PROPERTY, INCLUDING THE FOLLOWING:
1) Read all instructions before using this heater.
2) This heater is hot when in use. To avoid burns, do not let bare
skin touch hot surfaces. Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes, and curtains at least 3’
(0.9 m) from the front of the heater and keep them away from the
sides and rear.
3) Extreme caution is necessary when any heater is used by or
near children or invalids and whenever the heater is left operating
and unattended.
4) Always switch off the heater when not in use.
5) Do not operate any heater after the heater malfunctions, has
been dropped or damaged in any manner. Disconnect power at
service panel and have heater inspected by a reputable electrician
before reusing.
6) Do not use outdoors.
7) To disconnect heater, turn off power to heater circuit at main
disconnect panel.
8) Do not install less than 6 feet (1.8m) high from the floor and
keep the mounting bracket not less than 4 feet (1.2m) away from

4
any adjacent vertical surface. Keep at least 4.5 inches (11.5cm)
from the back wall (with or without using the wall hanging mounting
bracket).
9) Do not insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock or fire, or
damage the heater.
10) To prevent a possible fire, do not block air intakes or exhaust in
any manner.
11) A heater has hot and arcing or sparking parts inside. To reduce
the risk of fire, do not use it in areas where gasoline, paint, or
flammable vapors and liquids are used or stored.
12) Use this heater only as described in this manual. Any other use
not recommended by the manufacturer may cause fire, electric
shock, or injury to persons.
13) This product must be installed by a certified electrician, in
accordance with local codes.
14) Avoid the use of an extension cord because the extension cord
may overheat and cause a risk of fire.
15) This heater is not intended for use in bathrooms, laundry areas
and similar indoor locations. Never locate heater where it may fall
into a bathtub or other water container.
CAUTION –High temperature, risk of fire, keep electrical cords,
drapery, furnishings, and other combustibles at least 3 feet (0.9
m) from the front of the heater and away from the side and rear.
PET OWNERS WARNING:
The health of some small pets including birds are extremely
sensitive to the fumes produced during the first-time use of
many appliances. These fumes are not harmful to humans but
we recommended that you do not use your heater around birds
and small pets during its initial use until the manufacturing
corrosion coatings burn off.
SAVE THESE INSTRUCTIONS

5
Wall-Mounted Salamander Heater
Model: PS-10241
MANUFACTURER No.: PS-10241WP
Volt: 240 V, 1P
Watts: 10KW
Frequency: 60 Hz
Wiring diagram:
SPECIFICATIONS

6
Model: PS-30483
MANUFACTURER No.: PS-30483W
Volt: 480 V, 3P
Watts: 30KW
Frequency: 60 Hz
Wiring diagram:

7
Wiring Instruction
For 3 Phase Model: PS-30483
Open the cover.
After connection.
Earth Wire
L2 (Live Wire2
Black)
L3 (Live Wire3
Red)
L1 (Live Wire1
White)

8
A. Wall Mount Bracket
B. Hanger
C. Heater Housing
D. Front Exhaust Grill
E. ON/OFF Switch
F. Temperature Setting Knob
PARTS OF THE HEATER
A
C
D
F
E
B

9
WARNING:All wiring must be installed by a certified electrician
according to the electrical safety.
The heater must be grounded in accordance with all national and
local building codes.
All Wiring procedures and connections shall be in accordance
with the national and local codes having jurisdiction.
Before installation:
Disconnect the main supply connection.
The heater must be connected to individual branch circuit protected
by 65 Amp circuit breaker only.
Supply cables must be equipped with a dual pole circuit breaker
rating at least 240V 65A/pole as main cutoff switch of power
connection to the heater.
CAUTION: High temperature, risk of fire, keep electrical cords,
drapery, furnishings, and other combustibles at least 3 feet (0.9 m)
from the front of the heater and away from the side and rear.
WARNING: To reduce the risk of fire, do not store or use gasoline
or other flammable vapors and liquids in the vicinity of the heater.
INSTALLATION INSTRUCTION:
1. Keep the unit at least 6 feet (1.8m) away from the floor. This
minimum distance must be maintained.
2. Do not install closer than 4 feet (or 1.2 m) to any adjacent
vertical surfaces or walls.
3. Keep at least 4.5 inches (11.5cm) from the back wall (with or
without using the wall hanging mounting bracket).
4. Mark the drill-hole positions in the wall for the mounting bracket.
5. Drill the required holes with diameter fit for the anchor provided
for positioning the mounting bracket.
6. Insert the anchors.
7. Attach the mounting bracket to the wall and secure with
mounting screws.
INSTALLING INSTRUCTIONS

10
8. Hook the heater to the hanger with two hexagon head screws
and rubber pads, tighten the screws.
9. Insert the hexagon head screw through the hanger and the
mounting bracket, tighten the nut.

11
10. Run the electrical power supply cable in flexible conduit and
connect to the wiring compartment
12. Make the connections properly with connectors which are
suitable for the conductor size, including grounding wirings. And
after making the connections, arrange the pigtail leads of unit and
power supply wires in the wiring compartment.

12
WARNING - The heater must be properly installed before it is
used.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR
ARC FLASH :
Apply appropriate personal protective equipment (PPE)
and follow safe electrical work practices. See NFPA 70E.
A circuit breaker must be installed and serviced only by
qualified electrical personnel.
Always use a properly rated voltage sensing device to
confirm power is off.
Switch the ON/OFF switch to ON position to turn on the heater.
Then turn the thermostat to the farthest clockwise position. The
fan should start and the unit begins heating the room, and lamp
is light. After the room reaches comfort level, turn the
thermostat counterclockwise until the heater shuts off. The
heater will automatically cycle around this preset temperature.
To increase the temperature, turn the thermostat knob
clockwise. To lower the temperature, turn the thermostat
counterclockwise.
Select a thermostat setting.
Ambient temperature is regulated by adjusting the thermostat to a
desired position.Allowthe unit to operate and warm up the room.
When the desired temperature is reached, turn the control knob
counterclockwise until the heater turns off. This is your ideal
setting. The heater willstart automatically when the room
temperature drops below this set point, and will turn off when the
set point is reached.
To turn off the heater, switch the ON/OFF switch to
OFF position.
OPERATING INSTRUCTIONS

13
There is no user maintenance part except regular cleaning as
following description. All other servicing or maintenance should be
performed by qualified service personnel.
Before any cleaning, make sure that:
1. Disconnect power supply at source.
2. Wait for 60 minutes to ensure the heating element has cool
down, and your heater is now ready for cleaning.
Regular Cleaning:
1. Do not use cleaning liquid or other chemicals to spray on the
unit.
2. Interior dust can often be removed by using a vacuum cleaner
with a crevice tool attachment.
3. To clean enclosure, use a clean, soft and lightly damp cloth to
gently wipe off the dirt from the surface of the unit. Be sure not
to wet the heating element and the switches. Allow the unit to
dry completely before using it.
CAUTION: DO NOT ALLOW WATER TO RUN INTO THE
INTERIOR OF THE HEATER AS THIS COULD CREATE A FIRE
OR ELECTRIC SHOCK HAZARD, DAMAGING THE UNIT.
This product carries a one (1) year warranty against defects in
workmanship and materials. Profusion Heat agrees to replace a
defective product, within the stated warranty period, when returned
to the place of purchase with proof of purchase. This product is not
guaranteed against wear or breakage due to misuse and/or abuse.
MAINTENCE AND CLEANING
INSTRUCTIONS(separate page)
WARRANTY INFORMATION