Promise Pegasus 2 R4 User manual

R4/R6/R8/M4

WARNING
DO NOT disconnect the Thunderbolt cable until you have
completed the procedure to safely remove it. See “Safely Remove
Pegasus2 from Windows” on page 23 for details.
!
!WARNING
Use the power cord included with the Pegasus2.
ii
Pegasus2 Installation Guide for Windows

Promise Technologies
Contents
About this guide 1
system requirements for WindoWs 1
summAry of the setup procedure 1
pAcking List 2
hArdWAre 3
instALLAtion 5
step 1: doWnLoAd softWAre And driver 5
step 2: connect the pegAsus2 to your WindoWs computer 6
step 3: poWer onpegAsus2 7
step 4: instALL driver 8
step 5: instALL softWAre 11
step 6: formAt pegAsus2 With WebpAm pro 14
Format Pegasus2 with Windows 7 15
Format Pegasus2 with Windows 8 19
step 7: check firmWAre version With WebpAm pro 23
Updating Firmware 23
sAfeLy remove pegAsus2 from WindoWs 24
sAfeLy remove pegAsus2 on WindoWs 7 24
sAfeLy remove pegAsus2 on WindoWs 8 25
shutdoWn the pegAsus2 26

1
Promise Technologies
About this guide
The Pegasus2 Installation Guide for Windows is intended to guide the user through the
installation procedures to connect the device to a Windows computer, install the necessary
driver and software and begin using the device. For more complete information about the
device specications,details of the system hardware and advanced administration features,
please read the Product Manual.
References to “Pegasus2” throughout this guide apply to the Pegasus2 models R4, R6, R8
and M4 except where these models specically mentioned.
system requirements for WindoWs
The Pegasus2 hardware driver for Windows can be used on computers equipped with a
Thunderbolt™ port running any edition of Windows 7 or Windows 8. The software, WebPAM
PRO (web-based PROMISE Array Manager Professional), is also compatible with all Windows
7 and Windows 8 versions. WebPAM PRO is used for administration and management of the
Pegasus2.
summAry of the setup proCedure
The setup process for Windows is summarized below.
1. Go to the Promise website and download the driver and software used for the Pegasus2.
2. Connect the Pegasus2 to your Windows computer with a Thunderbolt cable.
3. Connect the power cord and power on the Pegasu2.
4. Install the PROMISE RAID Controller driver from the downloaded les.
5. Install WebPAM PRO from the downloaded les.
6. Launch WebPAM PRO and format the Pegasus2.

!WARNING
The fan contains hazardous moving parts. Keep ngers and other body
parts away.
2
Pegasus2 Windows Installation Guide
pAcking List
Check the shipping package to make sure you have the following items:
• Pegasus2 R4, Pegasus2 R6, Pegasus2 R8, or Pegasus2 M4
• Hard disk drives (four in R4 and M4, six in R6, eight in R8)
• Quick Start Guide
• Power cord
• Thunderbolt cable

Thunderbolt
Link LEDs Drive Power/
Status LED
Power
Button/LED
Drive
Activity LED
Drive Carrier
Pegasus2 R4 front view. The R6, R8 and M4 are similar in appearance
3
Promise Technologies
hArdWAre
This section provides a brief introduction to the hardware of the Pegasus2. For the purpose
of installation they are very similar.

Power
Connection
Thunderbolt Ports
Pegasus2 R4 back view. The R6, and R8 are similar, the R6 and R8 are taller
Power
Connection
Thunderbolt Ports
Pegasus2 M4 back view
4
Pegasus2 Windows Installation Guide

5
Promise Technologies
step 1: doWnloAd softWAre And driver
Follow these instructions to download the software and driver installation les for Windows
from the PROMISE website.
1. Go to the PROMISE website (www.promise.com) and click on Support in the banner at the top
of the web page, scroll down to Download Center.
2. In the Download Center page, scroll to nd the Pegasus2 Series in the pull-down menu on
the left side on the bottom of the menu. Then, in the pull-down menu on the right side, nd
Pegasus2 Series (the driver and software are the same for all models)
3. Under Download search results, the download links will be reveled below, click on the
download links for Pegasus2 driver for Windows and WebPAM PRO for Windows. Download
both les in separate downloads.
4. Place the les on your Windows system where they will be easy to locate and install them from
that location as instructed in steps 4 and 5.
instALLAtion
Follow the installation steps to setup and begin using the Pegasus2.

Pegasus2 M4 connected to Windows computer
6
Pegasus2 Windows Installation Guide
step 2: ConneCt the pegAsus2 to your WindoWs Computer
Insert one end of a Thunderbolt cable into the Thunderbolt port on the Pegasus2 and
connect the other end of the cable to a Thunderbolt port on your computer. Make sure the
cable connector is oriented correctly to the port on both the Pegasus2 and the computer. It
should t easily in place when correctly positioned.

Pegasus2 boot up LED behavior
Power
Button/LED
Drive Power/
Status LED
7
Promise Technologies
step 3: poWer onpegAsus2
Follow these steps to connect the power cord and power on the Pegasus2.
1. Attach the power cord on the back of the Pegasus2 unit. (See page 4 to see an
illustration of the back of device)
2. Plug the other end into a power source.
3. Press the Power Button. (See illustration of front of device below).
You will observes the that the Power Button LED turns orange.
It takes about 30 seconds to boot the Pegasus2 unit. When fully booted:
• The Power Button LED turns blue.
• The drive carrier Power/Status LEDs turn blue.

✓
8
Pegasus2 Windows Installation Guide
step 4: instAll driver
Locate the driver le you downloaded in Step 1 and follow the instructions in the InstallShield
Wizard to install the PROMISE RAID Controller driver. It will be necessary to restart the
computer after to complete the installation.
1. Double-click on the zipped le for installing the driver, the le name begins with
“PegasusRAID_WinDrv_Installer” followed by the version number.
The InstallShield Wizard appears. Click Next to begin the installation.

9
Promise Technologies
2. The License Agreement appears. Click to select the “I accept the terms of the license
agreement” option if you accept, and click on Next to continue.
3. You are informed that the driver has been installed successfully. Click on Finish to
continue.

!
WARNING
DO NOT disconnect the Thunderbolt cable while Windows is
running. To safely disconnect the Thunderbolt cable while the
computer is running, please read “Safely Remove Pegasus2
from Windows” on page 24.
10
Pegasus2 Windows Installation Guide
4. A message prompt appears informing you that a system restart is necessary, the “Yes, I
want to restart my computer now” option is selected by default. Click OK to restart now,
otherwise choose the “No, ...” option and restart later. The Pegasus2 cannot be used
until you reboot the computer.

11
Promise Technologies
step 5: instAll softWAre
Follow the instructions in this section to complete the installation of the Pegasus2 on your
Windows computer. You need to install WebPAM PRO software used for device management
and administration.
Locate the Installation program le downloaded previously in Step 1 and follow the instructions
in the InstallShield menu to install WebPAM PRO.
1. Double-click on the zipped le for installing WebPAM PRO, the le name begins with
“PegasusRAID_WebPAM_PRO” followed by the version number.
The InstallShield Wizard for WebPAM PRO appears. Click on Next to begin
installation.

12
Pegasus2 Windows Installation Guide
2. The License Agreement appears. Click to select the “I accept the terms of the license
agreement” option if you accept, and click on Next to continue.
3. Choose where to put the software on your computer. Click Browse to choose a specic
location, or click Next to accept the default destination. Click Next to continue.

13
Promise Technologies
4. The program is ready to be installed in the chosen location. Click Install to begin.
5. Installation of WebPAM PRO is completed. Click Finish to close the InstallShield
Wizard.

14
Pegasus2 Windows Installation Guide
step 6: formAt pegAsus2 With WebpAm pro
Now you are ready to format the Pegasus2 with a the NTFS le system for use as a direct
attached storage system with your Windows computer. Use WebPAM PRO to format the
RAID array and perform other administrative functions including changing the type of RAID.
For information on the other tasks and functions of WebPAM PRO, please read the product
manual. For the purpose of this installation guide, only the basic setup using the default
PROMISE Hardware RAID 5 array is described. This type of RAID provides the best balance
of performance and data safety. For more information on other RAID types, please read the
product manual
DO NOT use the Windows Disk Manager to change the RAID on the Pegasus2. Any
changes to the RAID array must be done using WebPAM PRO.
Follow the instructions below for the Windows OS you are running:
• Windows 7 users, see “Format Pegasus2 with Windows 7” on page 15.
• Windows 8 users, see “Format Pegasus2 with Windows 8” on page 19

15
Promise Technologies
Format Pegasus2 with windows 7
Windows 7 users follow the steps listed below to launch Web PAM PRO and format the
RAID:
1. To launch WebPAM PRO from the Windows desktop, double-click on the WebPAM
PRO icon located your Program Files folder. The path is Program Files > Promise >
WebPAM PRO > WebPAM PRO.
2. The login page appears. The User Name and Password used for logging in is the
same as the Windows OS user login user name and password. Type your Windows
User Name and Windows Password and click the Login button.

16
Pegasus2 Windows Installation Guide
3. After logging in, the WebPAM PRO Dashboard menu appears. Use this menu later to
view a summary of the device status. First you need to format the le system for the
Pegasus2.
4. Click on the Storage menu tab near the top of the menu. Then click on the Logical
Drive menu button to view the Logical Drive menu. Notice in the middle of the menu
a description of the RAID array that is already setup. The default setup is a RAID 5
using all the hard disks. If you want to change this, please see the product manual.
Otherwise, to begin using the Pegasus2 right away, click on the Format button to begin
the formatting procedure.

17
Promise Technologies
5. The formatting options appear in a new menu. You can type in a different name for the
Volume or leave the default PromiseRAID. Most users should use the Partition Type
set to the default GPTFormat. The other Partition Type option, MBRFormat (master
boot record) does not support Logical Drives greater than 2 TB. The Format Type is set
to NTFS, the standard Windows le system. Click Format to start formatting the array.
6. In order to safeguard against unintended changes to the RAID setup or le system,
the Pegasus2 requires that you conrm your decision to begin formatting the drives.
To continue formatting, type conrm in the space provided and click on the Conrm
button.