PulseTech XtremeCharge XC100-P Operating manual

Model XC100-P 12-Volt Charger
FEATURE AND USE GUiDE

Table of Contents
Use Guide...................................................................2
Specifications............................................................4
Five-Year Limited Warranty........................................5
Accessories...........................................................Back
Model XC100-P 12 Volt Charger
FEATURE AND USE GUiDE
FEATURES
Pulse
Desulfate
Test
Charge
Charge
Patented Pulse Technology increases the duty and life cycles of all 12 volt
batteries by up to five times
The unique application of patented PULSE conditioning provided by
Pulsetech®Products increases performance and life cycles of any size or
type of 12V lead-acid battery by minimizing the size of damaging lead sul-
fate crystals
Xtreme Charge®evaluates the battery during initial connection and tests
it continually to determine the appropriate charge rate based on your bat-
tery’s current capacity and condition. This TEST step also includes a “Bad
Battery” indication if it determines the battery is faulty and cannot be re-
charged.
A proprietary microprocessor controlled integrated charging process
measures both voltage and current and applies only the amount of charge
your battery is able to accept at any given time. As the patented pulse
technology is applied in combination with the saturation charge the bat-
tery’s condition improves. This proprietary process inhibits and removes
sulfation, protects your battery from overcharging and extends its operat-
ing life.
The XC100-P is also designed to be a MAINTENANCE charger for any type
of 12V lead-acid battery. Through application of our proprietary charge
algorithims and high frequency pulsing processes, your battery is main-
tained safely at its proper operating voltage indefinitely. If the charger is
connected to a discharged battery, its BULK charge capability (2.5 A ac-
tual/5 A effective) will re-charge the battery rapidly and safely so it can be
put back into service quickly.

2
USE GUIDE
Do not operate without first reading the Important Safety Instructions.
Connect red battery clip to positive (+) battery post. Then connect black
battery clip to negative (-) battery post.
Once you’ve connected the battery cables properly, you can begin the
charging process. Plug Xtreme Charge®into 110-220 VAC power source.
TEST
Green “On” light illuminates, indicating charger is
receiving proper ac input. If it’s connected to battery
correctly, red “Test” LED lights, indicating unit is
testing battery’s condition.
FAULT CONDITIONS
If red “No Connection” light illuminates, charger is
not connected to battery, or inline fuse on positive
battery lead needs to be replaced.
Should all the lights flash on and off and an audi-
ble warning buzzer be heard, battery clamps are
connected in reverse. Refer to Safety Instructions
booklet for detailed procedures to make sure leads
are connected properly.
If red “Bad Battery” LED lights, Xtreme Charge®
is connected to a 6V battery or a 12V battery that is
below 7 volts.

3
CHARGING CONDITIONS
Once charger has evaluated battery’s current
condition, “Test” light goes off. The appropriate
charge profile begins automatically.
Green “Charging” light indicates Xtreme Charge®
is providing bulk charge to battery.
Three green “Pulsing” LEDs light sequentially
as charger conditions battery. Patented Pulse
Technology enables it to accept and maintain its
maximum charge.
During “Test” cycle, charger determines battery’s
state of charge and illuminates the appropriate light:
“25%,” “50%,” “75%” or “100%.”
After battery is charged fully, green “100%” light
illuminates, and “Charging” light goes off. This indi-
cates charger is providing float charge to battery.
It may now be placed into service or left on the
Xtreme Charge®indefinitely to maintain peak condi-
tion.
If battery has been pulsing and charging for 24
hours continuously without reaching 100% state
of charge, unit discontinues charging. Red “Bad
Battery” light illuminates, indicating the battery is
non-rechargeable.

4
PULSE TECHNOLOGY
The unique application of patented PULSE conditioning provided by
Pulsetech®Products increases performance and life cycles of any size
or type of 12V lead-acid battery by minimizing the size of damaging lead
sulfate crystals. This allows your battery to accept more power than other
chargers can provide. Our patented PULSE technology is NOT “Pulse
Charging” which is commonly used in the market place today. It IS a total-
ly unique 1-2 punch provided by the independent application of our unique
high frequency conditioning pulse on one circuit and proprietary charging
algorithms on another. This helps ensure that your new batteries will stay
in like-new condition while your older batteries often improve dramatically.
SPECIFICATIONS
Xtreme Charge®XC100-P includes charger with fuse-protected quick-
disconnect battery clamps and lugs, Important Safety Instructions and
Feature and Use Guide.
Input Voltage - 100 - 250 VAC
Maximum Charge Current - 2.5A (5.0 Effective)
Nominal Float Voltage - 13.6V
Maximum Bulk Charge Voltage - 14.8V
Pulse Frequency - 40-50 kHz
Functional Output Cable Length - 8’
Agency Listing - CUL Approved
Housing - Weatherproof Rubberized base

5
FIVE-YEAR LIMITED WARRANTY
PULSETECH®PRODUCTS CORPORATION
XTREME CHARGE®BATTERY MAINTENANCE CHARGER
What Does This Warranty Cover? This warranty covers any defects in workmanship or
materials in this charger under normal use and service.
How Long Does the Coverage Last? This warranty runs for five (5) years from the date of
purchase.
What Will PulseTech Do? PulseTech will, at its option, replace or repair any defective unit
with a new or rebuilt unit at no charge.
What Does This Warranty Not Cover? This warranty applies only to the battery charger.
This warranty does not cover any other equipment, static damage, water damage, over-
voltage damage, dropping unit or damage resulting from extraneous causes including owner
misuse. In addition, PulseTech will not be responsible under this warranty if PulseTech deter-
mines that (1) upon examination that the circuit board failure was (A) caused by misuse,
neglect, accident, alteration or abnormal condition of operating or handling (including the fail-
ure to install the product in accordance with PulseTech’s instructions and observe the warn-
ings in the Feature and Use Guide and the Important Safety Instructions) or other conditions
beyond the control of PulseTech or (B) damaged in transit to PulseTech, and (2) the owner
is not the original purchaser that purchased the product through an authorized PulseTech
dealer or distributor. This warranty is void if owner attempts to disassemble the unit or to
modify the cable assemblies. IN NO EVENT SHALL PULSETECH BE LIABLE FOR ANY
DIRECT, SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL, PUNITIVE OR EXEMPLARY
DAMAGES, EXPENSES, LOST SAVINGS OR LOST PROFITS OR ANY OTHER DAMAGES OF
ANY KIND FROM ANY BREACH OF THIS WARRANTY OR OTHERWISE. Some states, prov-
inces or countries do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation may not apply to you.
How to Get Service? Contact PulseTech by calling 1-800-580-7554 for a Return
Authorization Number. Then send the product postage prepaid with proof of purchase
(sales receipt) within the warranty period to PulseTech. Battery chargers beyond the war-
ranty period are subject to the repair charges in effect at that time.
How Does State, Province or Country Law Apply? This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state, province to
province or country to country.
THIS WARRANTY IS THE SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER
WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
Southlake, TX 76092
U.S. Patent No. 7,834,592 B2
Additional U.S. patents pending
Model XC100-P

Full Enclosure Wall Bracket
Black powder coated 16-gauge
steel full enclosure designed to
suit heavy-duty, semi-permanent mount-
ing requirements as needed. For XC100-P only.
Part #: 100X810 Model: XC-BKT
To purchase any of these
items, contact an authorized
XtremeCharge®dealer, visit
www.PulseTech.net or call
800-580-7554.
25’ Extension Lead
Extend a standard lead by 25
feet with this extension. It fea-
tures quick-disconnect termi-
nals on both ends. Lead is 25 feet long.
Part #: 100X825 Model: XC-EXT-25
Quick Battery Tester
Assess your 12-volt battery’s
health quickly with this pocket-
sized tester. It will be the most
used tester in shops, garages
and any areas where battery
checks are performed.
Part #: 100X822 Model: XC822-TEST
Battery Lead with Clips
This 7.5-amp fuse-protected
cable is supplied with a quick-
disconnect terminal. Lead is 2
feet long.
Part #: 100X827 Model: XC-CLIPS
“Leave-On” Battery
Lead with Lugs
XtremeCharge®7.5-amp
fuse-protected cable comes
with a quick-disconnect termi-
nal. Lead is 2 feet long.
Part #: 100X830 Model: XC-LUGS
PRODUCTS &
ACCESSORIES
12V Xtreme Charger®
w/Pulse Maintenance
Ideally suited for AGM and
Maintenance-Free batteries.
Increases the duty and life
cycle of all 12V batteries up
to five times longer.
Part #: 100X010 Model: XC100-P
12V 2-Channel Charger
w/Pulse Maintenance
Double the charging capabi-
lites of the popular XC100-P
Xtreme Charge®12V Battery
Charger. Each station
charges at a 2.5 A
(5 A effective) charge rate at over 14.8 V.
Part #: 100X200 Model: X2
Quick Mount Wall Bracket
Black powder coated 20-gauge
steel. “Quick Mount’ flex design
for easy clip in and out use. Clip into
the wall bracket for shop use or un-clip it and
take it with you as needed. For XC100-P only.
Part #: 100X808 Model: XC-QM
QuadLink®
4-Channel Battery
Charger Multiplier
Gives your existing 6V or
12V charger, no matter what the
brand, the ability to charge up to FOUR batter-
ies at once.
Part #: 100X004 Model: XC-QL4
998XM101 04/12