Puretec IL-UB Series User manual

For correct operation & installation, it is essential to observe these instructions
JAN2022
User Guide
Inline Undersink Water Filtration System
IL-UB Series

2Installation & Operation Manual Copyright © Puretec Pty Ltd 2018
Puretec Customer Service
Thank you for purchasing a Puretec IL-UB system. Your system is a proven performer
manufactured from only quality materials and components and will give years of ‘spring fresh’
water free of impurities if maintained properly.
The Puretec IL-UB systems cartridges need replacing regularly to maintain optimum
performance. This is a simple procedure when following instructions. For cartridge replacements
contact your nearest Puretec stockist.
The Puretec filter systems cartridges need replacing regularly to maintain optimum performance.
This is a simple procedure when following instructions. For cartridge replacements contact your
nearest Puretec stockist.
Operation
The Puretec IL-UB systems are designed to run economically for many years, dependant on the
initial installation and periodical maintenance.
Flush systems for 10 minutes aer any period of non-use more than 2 days. For a period of non-
use of 2 weeks or more, it may be necessary to replace cartridge.
Cartridge Replacement
To maintain the high quality of the purified water the cartridges need changing every 6 months
(this is dependent on water quality and usage).
You can obtain replacement cartridges from your local Puretec dealer. To maintain performance
and warranty, use genuine Puretec replacements.
Order IN149C for a replacement cartridge to suit your IL-UB system.
Installation
This system comes complete with an installation kit enabling it to be connected to 15mm (½”)
male thread.
Installation Note: A water filter system/tap, like any product, has a limited life and may
eventually fail. Also sometimes failure happens early due to unforeseen circumstances. To
avoid possible property damage, this product should be regularly examined for leakage and/
or deterioration and replaced when necessary. A drain pan, plumbed to an appropriate drain or
outfitted with a leak detector, should be used in those applications where any leakage could
cause property damage, and/or the water supply should be turned off if no one is home/present.
Operation

3Inline Undersink Filter System User Guide
Installation Requirements
1. 15mm (½”) cold water line.
2. Min/Max pressure: 100 - 520 kPa.
3. Min/Max temperature 0° - 38°C (protect from freezing).
4. Suitable location for faucet.
Alternative fittings may be required if being connected to anything other than 15mm (½”) copper
pipe. No electrical or drainage requirements needed.
Note: Where line pressure exceeds 500 kPa, an approved pressure limiting device must be
installed to comply with Australian & New Zealand Plumbing Standards. (Ref. AS/NZS 3500.1-
2003, Clause 3.3.4)
Installation Procedure
1. Select suitable location for filtered water to be delivered (eg. sink). Remember to allow
access room for changing filters and a suitable place where water spillage will not
cause damage. Location should not be in direct sunlight.
2. Isolate water supply and cut copper pipe ready to install the connection tee.
3. Connect the ballvalve, pressure limiting valve and push-fit connector together with
thread tape. Flush a small amount of water to remove any debris.
4. Choose the best position for the faucet, taking into consideration height of jugs etc.
and also the drainage of any spills. Then drill a 12mm hole and install the faucet as in
step 5.
5. To install the faucet, connect the base of the faucet to the spout. Feed the escutcheon
and O-ring over the threaded end of the faucet (see figure 2, pg.6). Insert the threaded
end into the hole in the sink or bench. Feed the plastic washer, lock washer, locking nut,
gasket, cone washer and ¼” compression nut onto the threaded end and tighten the
nuts, ensuring the faucet is correctly positioned above the benchtop.
6. Install housing assembly by positioning it in the desired location, marking the position
of fixing holes and fixing with bracket screws (IL-UB Series can be mounted horizontally
or vertically). Allow room for the connecting tubes and for removing the filter bowls
(50mm).
7. Fit tubing into connectors (for quick-connect fittings see figure 3, pg. 7). Allow slack in
the tubing. Ensure flow arrow on cartridge is in direction of waterflow.
8. Install cartridge as per Cartridge Installation/Replacement.
9. Restore the water supply and check for leaks. The filters need to be only hand tight. If
they leak then undo housing and check the O-ring is seated properly.
Installation

4Installation & Operation Manual Copyright © Puretec Pty Ltd 2018
10. Run the system for at least 10 minutes (pull the faucet level towards you) to remove
carbon fines. Water may appear milky, but this is normal and is only tiny air bubbles
that will clear aer a short period.
Cartridge Installation/Replacement
1. Place container under filter in case of drips.
2. Isolate water supply and release water pressure by operating faucet lever.
3. Disconnect tubing from the cartridge. Discard old cartridge.
4. Remove packaging from the new cartridge. Connect tubing to either end of the
cartridge. Ensure flow arrow on cartridge is in direction of waterflow.
5. Restore water supply.
6. Check for any leaks and rectifying them, before leaving the unit.
7. Aer installing cartridges flush unit for 5 - 10 minutes.
User Guidelines
• Minimum operating pressure 100 kPa.
• Maximum operating pressure 520 kPa.
• Protect from freezing.
• Maximum operating temperature 38°C.
• Maximum flow rate 1.9 Lpm.
• This system must be installed according to local plumbing codes on the cold water line.
• Replacement Cartridges: See Cartridge Installation/Replacement section
• This system requires regular replacement of the filter cartridge to maintain proper
operation. Varying chlorine, sediment, or organic substance levels may affect
replacement frequency.
• Be sure to change the filter cartridge at least every 9,500 litres or every 6 - 12 months
which ever occurs first; or whenever you detect a change in taste, odour, or decrease in flow.
Caution:Do not use with water that is microbiologically unsafe or of unknown quality without
adequate disinfection before or aer the system.
Installation

5Inline Undersink Filter System User Guide
Figure 1
Installation
Faucet
Tubing 1/4" White
Inline Cartridge with
Quick Connect Fittings
Pressure Limiting
Valve (Multivalve)
Ball Valve
Cold Water Line

6Installation & Operation Manual Copyright © Puretec Pty Ltd 2018
Figure 2
Installation
Faucet
Escutcheon
Lock Washer
Gasket
1/4" Compression Nut
Counter Top
ø12.5 hole
Plastic Washer
Locking Nut
Cone Washer
1/4" Tube
O-Ring

7Inline Undersink Filter System User Guide
Figure 3
1. Cut the tube square and push into
the tube stop. For metal tube remove
burrs and chamfer tube end to prevent
O-Ring seal being damaged.
DISCONNECTION PROCEDURE
4. Push collet against body and
slide tube out of fitting.
2. Fitting grips before it seals. Ensure
tube is pushed into tube stop.
HOW TO USE QUICK CONNECT FITTINGS
3. Tube is secured in position.
Notes
All pictures and information are supplied as a guide only.
The complete range of Puretec products are developed, refined and made to meet and exceed
stringent specifications for the worldwide market.
Important Note: Sales of products are subject to our Terms & Conditions which are available
upon request. All specifications, prices and photos are a guide only and are subject to change
without notice. Please ring to confirm details. Do not use products with microbiological unsafe
water without adequate disinfection. Where water pressure exceeds maximum pressure
specifications, a pressure limiting valve must be fitted. Maximum flow depends on cartridge,
vessel, pressure, impurities etc.
Installation

Warranty
The warranty only applies if the product was used and/or installed in accordance with the user guide and/
or installation instructions. This warranty is given in lieu of all other express or implied warranties and
manufacturer shall in no circumstance be held liable for damages consequential (or otherwise) or delays
caused or faulty manufacturing except as excluded by law.
Applicable to all above, is that the warranties need to be approved by Puretec to ensure product was not
incorrectly used, installed or claimed. False and incorrect claims will be pursued at Puretec’s discretion,
including chargeable inspection and labour costs incurred.
Any claim under this warranty must be made within 1 year of the date of purchase of the product. This
product is warrantied to be free of defect of material and workmanship for 1 year from date of purchase. 1
Year warranty is 1 year parts and labour. Excludes cartridges.
Puretec is renowned for its quality and aer-sales support so if you have any issues please call 1300 140
140 (AU) or 0800 130 140 (NZ). To make a warranty claim, contact us directly or the place of original
purchase. All costs relating to a warranty claim must be approved by Puretec prior to any work being carried
out.
Puretec will pay your reasonable, direct expenses of claiming under this warranty. You may submit details and
proof of your expense claim to place of purchase for consideration.
Warranty/Australia
This warranty is given by Puretec Pty Ltd, ABN 44 164 806 688, 37-43 Brodie Road, Lonsdale SA 5160,
telephone no. 1300 140 140 and email at [email protected].
This warranty is provided in addition to other rights and remedies you have under law: Our goods come with
guarantees which cannot be excluded under the Australian Consumer Law. You are entitled to replacement or
refund for a major failure and to compensation for other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Warranty/New Zealand
This warranty is given by Puretec Ltd, Reg. No 4464398, PO Box 875 Cambridge 3450 NZ, Auckland 1061,
telephone no. 0800 130 140 and email at [email protected].
This warranty is provided in addition to other rights and remedies you have under law: Our goods come with
guarantees which cannot be excluded under the Consumer Guarantee Act. You are entitled to replacement or
refund for a major failure and to compensation for other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Warranty