Qomo QPC60 User manual

QOMO Portable Document Camera
QPC60
English
User’s Manual

• Welcome:
Thanks for purchasing this product. Please read the instructions carefully before using this
product.
• FCCComplianceStatement(ClassA):
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received;
including interference that may cause undesired operation.
• FederalCommunicationsCommission(FCC)Statement:
This Equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
• EuropeanCommunityComplianceStatement(ClassA):
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
• VCCI-A
This is a Class A product.
In a domestic environment this product may cause radio interference, in which case the user may
be required to take corrective actions.
The symbol of the crossed out wheeled bin indicates this product should not
be placed in municipal waste. Instead, you need to dispose of the waste equip-
ment by handing it over to a designated collection point for the recycling of
waste electrical and electronic equipment.

1
Warning
1. Do not allow children to operate the folding arm without supervision.
2. Do not look directly at the LED light source,
which may cause retinal damage.
3. Carry the product by holding the lower part of the main unit in both hands. Never hold the
product by the arm or the camera head only.
4. The camera can be damaged if it hits a desk surface or any hard object.
5. Never turn the arm in the opposite direction.
6. Be sure to hold the arm when turning it.
Do not put your hands here
to avoid injury.
180º
180º
180º
180º

2
Preparing the document camera
Knowing the document camera parts
Camera head
Lamp
Lamp power button
Lamp shuttle wheel
Led indicator
Remote control signal receiver
Control panel
LCD Display / Light Box
SD Card slot
USB port
TV System Switch
Antitheft slot
VGA Input Port
VGA Output Port
HDMI Output Port
Video Output Port
Audio Output Port
MIC Input Port
DC 5V Power Socket
Remote control signal receiver
AUDIOOUTMIC.IN
NTSC PAL
HDMIOUT
VIDEOOUT
VGAIN VGAOUT
PASSTHROUGH
DCIN(5V/2.5A)

3
Control Panel
Button Function
Select output port.
Select Aspect Ratio.
16:9 for 1280x720 / 4:3 for 1024x768
3” screen backlight on / off.
Power on / off.
Pass the signal from PC via RGB input
port to RGB output port.
Display toggle. Toggle between the 3”
LCD display and external display device.
Freeze the current image.
*Pause the clip while playing videos.
Show or hide OSD menu.
Record a video clip.
Capture a still image.
Playback mode to display recorded
pictures and video clips.
Invert image 180°.
Select and adjust.
/ Zoom out / Zoom in.
One-shot auto focus.

4
Remote Control
Button Function
Laser pointer / Brightness hotkey
* The function varies with model.
Power on / off
Freeze current image.
* Pause the clip while playing videos
Show or hide on-screen icons
To show or hide OSD menu
Playback mode to display recorded
pictures and video clips
Invert image 180°
Select and adjust
Record a video clip
Capture a still image
/ Zoom out / Zoom in
One-shot auto focus
/ Use the level bar to adjust the focus
manually
2X or 4X digital zoom
Highlight function on / off
Mask function on / off
Marco / Normal switch
Adjust highlighted / masked area size
Set color for highlighted / masked
area
Button Function
Increase / decrease the sound
volume.
Picture in Picture function on / off
*For displaying a still image as an
insert while displaying another image.
Infrared remote control can only be used
in proximity to the unit.
Remove the battery cover and load the
batteries into the battery compartment
correctly according to the “+” and “-”
symbols.
Be sure to use two AAA batteries. Do
not use new and old batteries or differ-
ent battery types together.

5
Setting up
This section provides useful tips on how to adjust the document camera smoothly for your needs.
Camera head
The camera head can turn freely at 180° up and down.
Illumination lamp
If the light is too dark, please turn on
the lamp on camera head to make best
exposure.
1. Press the lamp button to turn on / off the
illumination lamp.
2. Adjust the brightness by rotating the
shuttle wheel on top of the camera head.
Mechanical folding arm
The folding arm can turn freely 180° up
and down and the lower arm can rotate 180°
for a di󰘯erent working area.
180º
180º
180º
180º
180º

6
Recommended working area
▶Main working area
▶Secodary working area
If the document is not put in the recommend working area, the image should be rotated
by FLIP button ( ) on control panel or remote control.
13" x 9.7" (4:3)
13" x 7.2" (16:9)
13”
7.2”
9.7”
MAX. 17”
Min. 1.2”

7
Recommended panel switch function
Press Display toggle ( ) to preview images and videos in the external display device.
Adjusting the brightness
1. Press MENU button ( ) , and select the brightness mode ( ).
2. Use ( or ) buttons to increase or decrease the brighness level.
Adjusting the size
Use the Zoom button ( / ) to zoom in or zoom out the screen.

8
Adjusting the focus
▶Automatic focus
Press AF button ( ) to automatically focus. This function provides a one-shot auto-focus.
▶Manual focus
Use the manual focus button ( / )( )
on remote control to 󰘰netune the focus.
Anti-glare
Anti-glare sheet is a transparent plastic that is overlaid on top of shiny object or glossy surface to
reduce the glare.
To use, simply place the anti-glare sheet on top of shiny object to glossy surface such as magazine
to reduce light reection.
Functionsindicatedby canonlybeusedbytheremotecontrol.
+ Anti-glare

9
Inserting and Ejecting an SD / SDHC card
(Not supplied)
1. Insert a memory card (SD/SDHC/MMC/MMC 2.0) with the label facing up until it reaches the end
of the slot.
2. When the card is inserted successfully, the icon ( ) will appear on screen and the internal
memory will become inaccessible.
3. To remove the card, push the card to release it and then pull it out gently.
When using a brand new memory card, you are recommended to format the card with the
product. Do not turn off the power while formatting the SD card.
Even If your card has already been formatted on other devices, you may have to reformat
the card using the product.
If no external storage devices are connected, all les will be saved in the built-in memory.
USBSDCARD

10
Making the Connections
System diagram

Step 1 / Plugging in the Power Outlet
Use power adapter to connect DC IN connector on the product to a standard 100V~240V AC
power outlet.
The type of power adapter is depending on your countries / regions.
Step 2 / Output resolution and aspect ratio
Various output resolutions are available depending on the output and aspect ratio setting.
Please refer to the table listed below.
Output ASPECT RATIO TV system Resolution Vertical Frequency
HDMI
16:9 - 1280x720 50Hz/ 60Hz
4:3 - 1024x768 50Hz/ 60Hz
VIDEO
- NTSC 720x480 60Hz
-PAL 720x576 50Hz
VGA
16:9 - 1280x720 50Hz/ 60Hz
4:3 - 1024x768 50Hz/ 60Hz
AUDIOOUTMIC.IN
NTSC PAL
HDMIOUT
VIDEOOUT
VGAIN VGAOUT
PASSTHROUGH
DCIN(5V/2.5A)

11
When connecting HDMI OUT, it can play audio and video synchronization.
AUDIOOUTMIC.IN
NTSC PAL
HDMIOUT
VIDEOOUT
VGAIN VGAOUT
PASSTHROUGH
DCIN(5V/2.5A)
HDMI
Step 3 / Connecting with Components
Product Port Cable Display Device
Port
HDMI
HDMI OUT HDMI
VGA
RGB OUTPUT RGB INPUT
AUDIO OUTPUT
AUDIO IN
VIDEO
VIDEO OUTPUT VIDEO IN
AUDIO OUTPUT
AUDIO IN
▶HD TV
• ConnectviaHDMIOUTPUT
1. Use HDMI cable to connect to your HDTV via the HDMI OUT connector.
2. Make sure the output switch is set for HDMI mode and select an appropriate Aspect Ratio.

12
▶Standard TV
• ConnectviaVGAOUTPUT
1. To display images, you can use VGA cable to connect to your television’s RGB port via the
VGA OUT connector.
2. Make sure the output switch is set for VGA mode and select an appropriate Aspect Ratio.
3. To output sound, you can simply use internal speaker, or connect a speaker to the AUDIO
OUT port.
• ConnectviaVIDEOOUTPUT
1. To display images, you can use VIDEO cable(yellow) to connect to the C-video in on your
television via the VIDEO OUT connector.
2. Make sure the output switch is set for VIDEO mode.
3. To output sound, use the AUDIO cable to connect to your television via the AUDIO OUT
connector a TV.
Please make sure to adjust TV SYSTEM(NTSC / PAL) switch setting.
NTSC:America, Taiwan, Panama, Canada, Chile, Japan, Korea and Mexico.
PAL:Europe, China and Hong Kong.
AUDIOOUTMIC.IN
NTSC PAL
HDMIOUT
VIDEOOUT
VGAIN VGAOUT
PASSTHROUGH
DCIN(5V/2.5A)
LINEIN
RGB
AUDIOOUTMIC.IN
NTSC PAL
HDMIOUT
VIDEOOUT
VGAIN VGAOUT
PASSTHROUGH
DCIN(5V/2.5A)
AVIN

13
Connect to a speaker system
Plug a 3.5mm plug speaker to AUDIO OUT connector on the product. Only the audio from the
video playback is supported.
Connect to an external microphone
Plug a 3.5mm mono microphone to MIC. IN connector on the product.
The built-in microphone will be disabled when an external microphone is connected.
If HDMI OUT and AUDIO OUT are connected simultaneously, the audio from HDMI OUT
device will be disable but output from AUDIO OUT device.
Take caution when using earphones. Adjust the volume down to prevent hearing damage
due to loudness.
AUDIOOUTMIC.IN
NTSC PAL
HDMIOUT
VIDEOOUT
VGAIN VGAOUT
PASSTHROUGH
DCIN(5V/2.5A)
LINEIN
AUDIOOUTMIC.IN
NTSC PAL
HDMIOUT
VIDEOOUT
VGAIN VGAOUT
PASSTHROUGH
DCIN(5V/2.5A)

14
Connect to a computer
▶ConnectviaVGAcable
Use VGA cable to connect VGA IN connector on the product to the VGA OUT connector on the
computer.
▶ConnectviaUSB
Press MENU ( ) button → select "USB Connect". Choose "Disk" to connect mass
storage. Choose "PC Cam" to be as a PC-Cam.
To display computer image, press PC button ( ) on the control panel.
For laptop to output display mode, use the keyboard command ( Fn + ) to swtich
between the display modes. For different command, please refer to your laptop manual.
The signal is only pass through from VAG IN port to VGA OUT port on document camera.
It cannot display computer image on 3” LCD panel. Please connect an output device to
display the image on computer.
USBSDCARD
AUDIOOUTMIC.IN
NTSC PAL
HDMIOUT
VIDEOOUT
VGAIN VGAOUT
PASSTHROUGH
DCIN(5V/2.5A)
RGB

15
Basic operation
1. Press MENU ( ) button on the remote control or control panel.
2. Press ( or ) button to toggle between tabs.
3. Press ( ) to make a selection and display the setting selections.
4. Use ( or ) to adjust the setting.
5. Press ( ) to make the new setting activate.
6. Press MENU ( ) button again to hide the OSD menu.
Menu options in Preview Mode
Name icon Option Description
Brightness -Use the Right / Left buttons to make the image
brighter / darker
Still Resolution 2M / 5M / 12M Select the desired still image resolution.
Effect
Graphic 1 To improve the tint of color-based subjects
such as pictures or figures, select Graphic 1
or Graphic 2, which represent different level of
tint, to satisfy your presentation.
Graphic 2
Text 1 The function is designed especially for text-
based documents to which can be enhanced
white and black subjects such as characters
and lines. The effect goes stronger as the
number increase.
Text 2
B&W
To output a black & white camera image.To
make the image easier to view,select this when
shooting black & white documents etc.
Negative To output a negative camera image.
Quick Zoom 2X / 4X Set the quick zoom to 2X or 4X.
Focus
Normal Select standard mode for 20cm ~ 00.
Macro /
Microscope
Select Macro/Microscope mode to take close-
ups or while connecting to a microscope.

16
Name icon Option Description
HD Rec. Mode On / Off
Enable HD Rec. mode on / off
*When enter the HD Rec. mode, the output
signal will be terminated and then press
“Recoding” button to record videos in High
Denition (1280x720) resolution.
SETTING
Beep On / Off Enable beep sound on / off
Flicker 50Hz / 60Hz
Set icker frequency to 50Hz or 60Hz
The icker setting is based on the frequency
standard of your local power supply.
USB
Connect
Disk Select “Disk” to enter Mass storage Mode
PC cam Select “PC Cam“ to enter PC Cam Mode
Off Disable USB function
Language - Allows you select the language used for OSD
Volume - Use the Right / Left buttons to adjust volume
Clock - Set date and time
Format No / Yes Format the storage medium. Note that all les
stored in the medium will be gone.
Reset
default No / Yes Restore factory defaults. Note that your current settings will be overwritten.
Menu options in Playback Mode
Name icon Option Description
File Info - View the le’s title , saved date and time , size
and the length of recording.
Slide show Off / 5s / 10s / 30s Start a slide show with selected interval time.
Delete one Yes / No Delete current le.
Delete all Yes / No Delete all images of the same type stored in the
memory.

17
Recording a video clip / Taking a still
picture
1. Choose the focus mode according to distance to object:
Normal mode for 20cm to ∞.
Macro mode ( ) or ( )( ) for 5cm ~ 20cm.
2. Use the Zoom button ( / ) to zoom in or zoom from the screen.
3. Automatic focus/Manual focus
Press AF button ( ) to focus automatically. This function provides a one-shot auto-focus.
Use manual focus button ( / )( ) on the remote control to ne-tune focus.
4. Press the Record button ( ) to start recording and press it again to stop recording.
Press the Shutter button ( ) to take a still picture.
The default resoulution of video clip is SVGA.
Use “REC HD” mode to record high resolution video in HD720p. “REC HD” only sup-
ports the built-in 3” LCD display.
Playing-back
1. Press PLAYBACK button ( ) .
2. The last recorded picture or video clip will play.
3. Use Up / Down button to choose les.
4. Press the zoom out button ( ) . The 9-image display will appear.
Functionsindicatedby canonlybeusedbytheremotecontrol.

18
Copying les to your computer
Please notice that the video clips are recorded in MP4 format and are compiled as CLIPxxxx.mp4
(xxxx are four serial numbers).
Before viewing these videos on your PC, you may need to install some media programs.
1. Power on the product.
2. Connect the product to your computer with USB cable.
3. Press MENU ( ) → select “USB Connect“ → choose “Disk“. The built-in memory or external
memory will be detected.
Then, You can view the image data on a SD card on the PC’s viewer software or simply cut and
paste the 󰘰le to your PC.
When the operating panel or the remote control is in operation, do not connect or
disconnect the USB cable, as this could cause the product to malfunction. This may
cause malfunctions to occur.
If you would like to change the setting, please refer to the “Advanced settings” section
for more information.
Using product as a PC cam
Installingthesoftware
The PC Camera driver is included in the accessory CD, and therefore you should install the driver
before using PC Camera.
Startingtheapplication
1. Connect the product to your computer.
Turn on your computer, then connect the accessory USB cable to the USB port of your
computer.
Make sure the connector and the port are correctly aligned.
2. Switch to PC Cam mode.
Connect the other end of the USB cable to the main unit.
Power on press MENU ( ) → select USB Connect → select PC Cam ( ) and press OK
button to con󰘰rm.
3. Launch PC Camera
After the product is correctly connected to and detected by your PC, you are ready to launch
your favorite software (such as MSN Messenger or Yahoo Messenger) to use PC Camera
function.