Rauch AXIS EMC ISOBUS User manual

AXIS EMC ISOBUS
Complementary instructions
Read carefully before
using the machine!
Keep for future reference.
This operator's manual/mounting manual
is to be considered as part of the
machine. Suppliers of new and second-
hand machines are required to document
in writing that the operator's manual/
mounting manual was delivered with the
machine and handed over to the
customer.. Version 4.11.00
5902180-h-en-0821
Original instructions

Dear customer,
By purchasing the AXIS EMC ISOBUS machine control unit for the AXIS EMC fertilizer spreader,
you have shown confidence in our product. Thank you very much! We want to justify this
confidence. You have purchased a powerful and reliable machine control unit.
However, in case unexpected problems arise, our customer service department is always there for
you.
Please read this operator's manual as well as the operator’s manual for the machine
carefully before using the machine, and follow the advice given.
This manual may also describe equipment that is not included in your machine control unit.
Note the serial number of the machine control unit and of the machine
The AXIS EMC ISOBUS machine control unit has been calibrated at the factory
for the mineral fertilizer spreader with which it was supplied. It cannot be
connected to another machine without recalibration.
Please enter the serial number of the machine control unit and of the machine
here. When connecting the machine control unit to the machine, these numbers
must be checked.
Serial number of electronic machine control unit:
Machine serial number:
Machine year of manufacture:
Technical improvements
We continuously strive to improve our products. For this reason, we reserve the right to make any
improvements and changes to our machine that we consider necessary without notice. We do not
accept any obligation to make such improvements or changes on machines that have already been
sold.
We will be pleased to answer any other questions that you might have.
Yours sincerely
RAUCH Landmaschinenfabrik GmbH

Table of contents
1 User instructions 7
1.1 About this operator’s manual 7
1.2 Meaning of warnings 7
1.3 Notes on text descriptions 8
1.3.1 Instructions and procedures 8
1.3.2 Lists 8
1.3.3 References 9
1.3.4 Menu hierarchy, keys and navigation 9
2 Layout and function 10
2.1 Overview of supported machines 10
2.2 Display 10
2.2.1 Description of the operating screen 11
2.2.2 Display fields 12
2.2.3 Display of the metering slide status 14
2.2.4 Display of sections 15
2.3 Library of icons used 16
2.3.1 Navigation 16
2.3.2 Menus 16
2.3.3 Operating screen icons 17
2.3.4 Other icons 20
2.4 Structural menu overview 21
3 Attachment and installation 23
3.1 Tractor requirements 23
3.2 Connections, sockets 23
3.2.1 Power supply 23
3.2.2 Connecting the machine control unit 23
3.2.3 Dosing slider preparation 27
4 Operation 28
4.1 Switching on the machine control unit 28
4.2 Navigation within the menus 29
4.3 Main menu 30
4.4 Fertilizer settings 31
Table of contents
AXIS EMC ISOBUS 5902180-h-gb- 3

4.4.1 Application rate 34
4.4.2 Set the working width 35
4.4.3 Flow factor 35
4.4.4 Drop point 37
4.4.5 Calibration 37
4.4.6 Disc type 40
4.4.7 RPM 41
4.4.8 Limited border spreading mode 42
4.4.9 Border spreading application rate 42
4.4.10 Calculate OptiPoint 43
4.4.11 GPS Control info 44
4.4.12 Fertilizer charts 45
4.5 Machine settings 49
4.5.1 AUTO/MAN mode 51
4.5.2 +/- quantity 52
4.6 Fast emptying 53
4.7 System/Test 55
4.7.1 Total data counter 56
4.7.2 Test/diagnosis 57
4.7.3 Service 60
4.8 Info 60
4.9 Weighing/Trip counter 60
4.9.1 Trip counter 61
4.9.2 Rest (ka, ha, m) 62
4.9.3 Zero scales 63
4.10 Operating lights (SpreadLight) 64
4.11 Hopper cover 65
4.12 Special functions 67
4.12.1 Changing the system of units 67
4.12.2 Using the joystick 68
4.12.3 WLAN module 71
5 Spreading operation 73
5.1 Requesting the remaining quantity during spreading 73
5.2 Refilling 73
5.3 TELIMAT border spreading unit 74
5.4 Electrical TELIMAT unit 75
5.5 Working with sections 76
5.5.1 Displaying the spreading type in the operating screen 76
5.5.2 Spreading with reduced sections: VariSpread V8 77
5.5.3 Spreading with reduced sections: VariSpread pro 79
5.5.4 Spreading operation with one section and in border spreading mode 82
5.6 Spreading with the automatic operating mode (AUTO km/h + AUTO kg) 83
5.7 Idle measurement 84
5.7.1 Automatic idle measurement 84
5.7.2 Manual idle measurement 86
5.8 Spreading with the AUTO km/h operating mode 86
Table of contents
45902180-h-gb- AXIS EMC ISOBUS

5.9 Spreading with the MAN km/h operating mode 87
5.10 Spreading in the MAN scale operating mode 88
5.11 GPS control 90
6 Alarm messages and possible causes 94
6.1 Meaning of the alarm messages 94
6.2 Fault/alarm 98
6.2.1 Acknowledging an alarm message 99
7 Special equipment 100
8 Guarantee and warranty 101
Table of contents
AXIS EMC ISOBUS 5902180-h-gb- 5

6

1 User instructions
1.1 About this operator’s manual
This operator's manual is an integral part of the machine control unit.
The operator’s manual contains important instructions for safe, proper, and economic use and
maintenance of the machine control unit. Compliance with its stipulations helps to avoid risks,
reduce repair costs and downtime, and to increase the reliability and service life of the machine
controlled with it.
The operator's manual must be kept in an easily accessible location close to where the control unit is
used (e.g., in the tractor).
The operator's manual does not replace your own responsibility as operator and operational staff of
the machine control unit.
1.2 Meaning of warnings
The warnings in the operator’s manual are classified according to the severeness of the risk and the
probability of its occurrence.
The warning symbols draw attention to the unavoidable residual risks inherent in the design to which
users of the machine are exposed. The warnings used are structured as follows:
Symbol + signal word
Explanation
Level of danger of warnings
The level of danger is indicated in the signal word. The levels of danger are classified as follows:
DANGER!
Type and source of danger
This warning warns of a danger posing an immediate threat to the health and life of people.
Ignoring these warnings will result in severe injury or death.
▶Always observe the measures described to prevent this danger.
WARNING!
Type and source of danger
This warning warns of a potentially dangerous situation for personal health.
Ignoring these warnings leads to severe injury.
▶Always observe the measures described to prevent this danger.
1. User instructions
AXIS EMC ISOBUS 5902180-h-gb- 7

CAUTION!
Type and source of danger
This warning warns of a potentially dangerous situation for personal health.
Ignoring these warnings leads to injury.
▶Always observe the measures described to prevent this danger.
NOTICE!
Type and source of danger
This warning warns of material and environmental damage.
Ignoring these warnings will result in damage to the machine and to the environment.
▶Always observe the measures described to prevent this danger.
Dies ist ein Hinweis:
Allgemeine Hinweise enthalten Anwendungstipps und besonders nützliche Informationen, jedoch
keine Warnungen vor Gefährdungen.
1.3 Notes on text descriptions
1.3.1 Instructions and procedures
Steps that the operator must carry out are shown as a numbered list.
uInstruction for action step 1
uInstruction for action step 2
Instructions involving only one step are not numbered. The same applies for actionsteps that do not
have a specific sequence.
A bullet is placed in front of these instructions:
• Handling instruction
1.3.2 Lists
Lists without a specific sequence are shown as lists with bullet points:
• Property A
• Property B
1. User instructions
85902180-h-gb- AXIS EMC ISOBUS

1.3.3 References
References to other sections in the document are shown with paragraph number, header text and/or
page number:
•Example: Please also note 2 Layout and function
References to other documents are shown as information or instructions without the exact chapter or
page number:
•Example: Follow the instructions in the operator’s manual of the universal drive shaft
manufacturer.
1.3.4 Menu hierarchy, keys and navigation
Menus are the entries listed in the main menu window.
The menus list submenus and/or menu items where settings can be made (selection lists, text or
number entries, starting a function).
The various menus and buttons of the machine control unit are illustrated in bold letters.
The hierarchy and the path to the requested menu item are marked with an > (arrow) between menu
and/or menu item(s):
• System / Test> System / Test > Test/diagnosis means that you can reach the menu item Voltage
via the menu item System / Test and the menu item Test/diagnosis.
○ The arrow > corresponds to the operation of the scroll wheel and/or the button at the screen
(touchscreen).
1. User instructions
AXIS EMC ISOBUS 5902180-h-gb- 9

2 Layout and function
Due to the great variety of different ISOBUS-compatible terminals, this chapter is limited to the
functions of the electronic machine control system without indicating a specific ISOBUS terminal.
• Please observe the instructions for the operation of your ISOBUS terminal in the
corresponding operator's manual.
2.1 Overview of supported machines
Some models are not available in all countries.
• AXIS H 30.2 EMC, AXIS H 30.2 EMC + W
• AXIS H 50.2 EMC + W
• AXIS M 20.2 EMC, AXIS M 20.2 EMC + W
• AXIS M 30.2 EMC, AXIS M 30.2 EMC + W
• AXIS-M 50.2 EMC + W
Supported functions
• Spreading depending on forward speed
• Electrical drop point setting
• RPM control
○ AXIS-M 20.2/30.2/50.2 EMC (+W): Drive shaft speed
○ AXIS-H 30.2/50.2 EMC (+W): Spreading disc speed
• EMC - mass flow control
• Continuous section control
2.2 Display
The display shows the current status information as well as the selection and input options for the
electronic machine control unit.
The most important information concerning the operation of the machine is displayed in the operating
screen.
2. Layout and function
10 5902180-h-gb- AXIS EMC ISOBUS

2.2.1 Description of the operating screen
The exact representation of the working screen depends on the actual settings selected and on
the machine type.
Fig. 1: Machine control unit display
[1] Current application rate from the fertilizer
settings or the task controller
Button: direct entry of the application rate
[2] Fertilizer information display (fertilizer name,
working width and spreading disc type)
button
Button: Adjustment in the fertilizer chart
[3] Metering slide position, right/left
[4] Drop point position, right/left
[5] Quantity change, right/left
[6] Spreading disc speed, right/left
[7] Metering slide opening status, right/left
[8] Function keys
[9] Freely definable display fields
[10] AXMAT- Function is active
[11] Mineral fertilizer spreader display
[12] Selected operating mode
[13] Display of boundary/border settings
2. Layout and function
AXIS EMC ISOBUS 5902180-h-gb- 11

Fig. 2: Machine control unit display
[1] Current application rate from the fertilizer
settings or the task controller
Button: direct entry of the application rate
[2] Fertilizer information display (fertilizer name,
working width and spreading disc type)
Button: Adjustment in the fertilizer chart
[3] Function keys
[4] Freely definable display fields
[5] Metering slide opening status, right/left
[6] AXMAT- Function is active
[7] PTO speed
[8] Drop point position, right/left
[9] Metering slide position, right/left
[10] Mineral fertilizer spreader display
[11] Selected operating mode
[12] Display of boundary/border settings
2.2.2 Display fields
The three display fields in the operating screen can be individually adjusted and assigned the following
values as desired:
• Forward speed
• Flow factor (FF)
• ha trip
• kg trip
• m trip
• kg left
• m left
• ha left
• Idle time (Time until the next idle measurement)
• Torque (Spreading disc drive)
2. Layout and function
12 5902180-h-gb- AXIS EMC ISOBUS

Fig. 3: Display fields
[1] Display field 1
[2] Display field 2
[3] Display field 3
Select display
uPress the corresponding display field in the touch screen.
The available options are displayed in a list.
uSelect the new value to be assigned to the display field.
uPress the OK button.
The operating screen is displayed.
The respective display field displays the new value.
2. Layout and function
AXIS EMC ISOBUS 5902180-h-gb- 13

2.2.3 Display of the metering slide status
Fig. 4: Display of the metering slide status
[A] Spreading operation inactive
[1] Section deactivated
[2] Section activated
[B] Machine in spreading operation
[3] Section deactivated
[4] Section activated
In border spreading mode, you can immediately deactivate an entire spreading side. This is
particularly helpful for a quick spreading operation in field corners.
uSoftkey section reduction press longer than 500 ms.
2. Layout and function
14 5902180-h-gb- AXIS EMC ISOBUS

2.2.4 Display of sections
Fig. 5: Display of the section statuses
[1] Section/boundary spreading toggle key
[2] Reduce right section button
[3] Activated sections on entire working width
[4] Right section is reduced by several partial
sections
Further display and setting options are explained in chapter 5.5 Working with sections.
We recommend restarting the terminal in the following cases:
• You have changed the working width.
• You have opened a different fertilizer chart entry.
After restarting the terminal, the section display changes to match the new settings.
2. Layout and function
AXIS EMC ISOBUS 5902180-h-gb- 15

2.3 Library of icons used
The AXIS EMC ISOBUS machine control unit displays icons for the individual menus and functions on
the screen.
2.3.1 Navigation
Icon Meaning
Go to the left; previous page
Go to the right; next page
Back to the previous menu
Back to main menu
Switch between working screen and menu window
Acknowledgment of warning messages
Cancellation, closing the dialog window
2.3.2 Menus
Icon Meaning
Switch from a menu window directly to the main menu
Switch between working screen and menu window
SpreadLight operating lights
2. Layout and function
16 5902180-h-gb- AXIS EMC ISOBUS

Icon Meaning
Hopper cover
Fertilizer settings
Machine settings
Fast emptying
System/Test
Information
Weighing/Trip counter
2.3.3 Operating screen icons
Icon Meaning
Start the application rate regulation
The spreading operation has started; stop the application rate regulation
Start spreading discs
Rotate the spreading discs; stop the spreading discs
Reset the quantity adjustment to the pre-set application rate
Switch between working screen and menu window
Switch between boundary spreading and sections on the left, right or both spreading sides
2. Layout and function
AXIS EMC ISOBUS 5902180-h-gb- 17

Icon Meaning
Sections on the left side, boundary spreading on the right spreading side
Sections on the right side, boundary spreading on the left spreading side
Boundary spreading on the left, right or both spreading sides
Selection of the surplus/shortage quantity on the left, right or both spreading sides (%)
Quantity adjustment + (plus)
Quantity adjustment - (minus)
Quantity adjustment, left + (plus)
Quantity adjustment, left - (minus)
Quantity adjustment, right + (plus)
Quantity adjustment, right - (minus)
Manual quantity adjustment + (plus)
Manual quantity adjustment - (minus)
Increasing the spreading disc speed (plus)
2. Layout and function
18 5902180-h-gb- AXIS EMC ISOBUS

Icon Meaning
Reducing the spreading disc speed (minus)
Left spreading side inactive
Left spreading side active
Right spreading side inactive
Right spreading side active
Reduce left section (minus)
In border spreading mode:
Pressing and holding (> 500 ms) immediately deactivates an entire spreading side.
Increase left section (plus)
Reduce section, right (minus)
In border spreading mode:
Pressing and holding (> 500 ms) immediately deactivates an entire spreading side.
Increase right section (plus)
Activate right boundary spreading function/TELIMAT
Right boundary spreading function/TELIMAT active
Activate left boundary spreading function
Left boundary spreading function active
2. Layout and function
AXIS EMC ISOBUS 5902180-h-gb- 19

2.3.4 Other icons
Icon Meaning
Start idle measurement, in the main menu
Limited border spreading mode, in the working screen
Full border spreading mode, in the working screen
Limited border spreading mode, in the main menu
Full border spreading mode, in the main menu
Operating mode AUTO km/h + AUTO kg
Operating mode AUTO km/h
Operating mode MAN km/h
Operating mode MAN scale
EMC control deactivated
Loss of the GPS signal (GPS J1939)
The minimum mass flow is undercut
The minimum mass flow is undercut
2. Layout and function
20 5902180-h-gb- AXIS EMC ISOBUS