Raymarine Maxiview ST80 Manual

Distributed by
Any reference to Raytheon or
RTN in this manual should be
interpreted as Raymarine.
The names Raytheon and RTN
are owned by the
Raytheon Company.

ST80
Maxiview
Operation & Setup

Maxiview

ST80 MaxiviewOperationandSetup 1
Package Contents
1. Maxiview display head
2. Thumb nuts (2)
3. Threaded fixing studs (2)
4. White sun cover
5. SeaTalk cable
6. Installation template
7. Operation manual
8. Warranty card
9. Operation cue card
10. Display head installation guide

ST80Maxiview OperationandSetup2
Contents
Chapter 1: Introduction ............................................................. 7
Quick Reference Guide ............................................... 7
Chapter 2: Operation ............................................................... 10
2.1 General ...................................................................... 10
Operating the Maxiview using the Remote Keypad .... 10
Keypad Beeps ........................................................... 10
Gaining Control of the Maxiview ........................ 10
2.2 Speed Chapter ............................................................ 11
Boat Speed Page........................................................ 11
Speed Over Ground (SOG) Page ................................ 12
Velocity Made Good (VMG) to Wind Page ................ 12
Log/Trip Page ........................................................... 13
Average Speed .......................................................... 14
Maximum Speed Page............................................... 14
2.3 Depth Chapter ............................................................ 15
Depth Page................................................................ 15
Minimum Depth Page ............................................... 16
Depth Offset Page ..................................................... 16
2.4 Wind Chapter ............................................................. 17
Apparent Wind Speed page ....................................... 17
Apparent Wind Angle Page ....................................... 17
True Wind Speed Page (Relative to the Vessel) .......... 18
True Wind Angle (Relative to the Vessel) .................. 18
True Wind Angle (Referenced to the Compass) .......... 19
2.5 Heading Chapter......................................................... 19
Heading Page ............................................................ 19
Steering Page ............................................................ 20
Course Over Ground (COG) Page .............................. 20
Bearing to Waypoint (BTW) Page ............................. 21
Tack Course Page...................................................... 21

ST80 MaxiviewOperationandSetup 3
2.6 Navigate Chapter........................................................ 22
Position Page............................................................. 22
Course Over Ground (COG) & Bearing to Waypoint
(BTW) ...................................................................... 22
Cross Track Error ...................................................... 23
Velocity Made Good (VMG) to Waypoint Page ......... 23
Waypoint Data Page.................................................. 24
Date/Time/Tide Page ................................................ 25
2.7 Race Timer Chapter.................................................... 26
Race Start Page ......................................................... 26
2.8 Multi-Line.................................................................. 27
Help/Setup Page........................................................ 27
Multi-line Setup ........................................................ 28
List of Multi-line Selections ................................ 29
Multi-line Factory Defaults ................................. 30
2.9 Illumination ............................................................... 31
Resetting the Contrast................................................ 32
2.10 Data Lost.................................................................. 32
2.11 Man Overboard and Alarms ...................................... 32
Man Overboard ......................................................... 32
Dead Reckoned MOB......................................... 32
Lat/Lon MOB ........................................................... 33
Incomplete MOB Data .............................................. 33
MOB Audible Alarm .......................................... 34
Alarms ...................................................................... 34
Audible Alarms ......................................................... 35

ST80Maxiview OperationandSetup4
Chapter 3: Setup ...................................................................... 36
3.1 Entering Setup ............................................................ 36
Speed Chapter ........................................................... 37
Response Pages .................................................. 37
Trend Indicator Thresholds ................................. 38
Display Format................................................... 40
Depth Chapter ........................................................... 40
Depth Response.................................................. 41
Trend Indicator Thresholds ................................. 41
Depth Display Format......................................... 42
Wind Chapter............................................................ 42
Wind Speed Response ........................................ 43
WindAngleResponse ........................................ 43
Display Format................................................... 44
Multiline Chapter ...................................................... 44
Editing Rights .................................................... 45
3.2 Instrument Setup ........................................................ 46
Transducers Page ...................................................... 46
Sail/Power/Custom Selection .................................... 47
Custom .............................................................. 48
Contents Setup ................................................... 49
Title Control....................................................... 50
Variation ............................................................ 51
True/Magnetic Heading...................................... 52
Lamp Offset Adjustment .................................... 53
Contrast Adjustment ........................................... 54
LCD Inversion ................................................... 55
Alarm Control .................................................... 56
3.3 Quitting User Setup .................................................... 57

ST80 MaxiviewOperationandSetup 5
Chapter 4: CodeLock Security................................................. 58
4.1 What is CodeLock? .................................................... 58
Master’s .................................................................... 58
Slave’s ...................................................................... 58
4.2 Analogue Display Heads............................................. 59
Automatic CodeLock Systems................................... 59
Manual CodeLock System......................................... 59
4.3 Enabling CodeLock.................................................... 59
Chapter 5: Problem Solving..................................................... 60
Chapter 6: EMC and Servicing Guidelines .............................. 61
6.1 Important information................................................. 61
6.2 Installation ................................................................. 61
6.3 Check Before Going to Sea ......................................... 62
6.4 Servicing and Safety ................................................... 62
Chapter 7: Specification ......................................................... 63

ST80Maxiview OperationandSetup6

ST80 MaxiviewOperationandSetup 7
Chapter 1: Introduction
D1580-1
maxiview
SPEED
KNOTS
The Maxiview is a large-screen LCD repeater capable of displaying
single or multiple lines of alphanumeric SeaTalk data.
With a display area measuring 126 x 70mm (5 x 2.7in), the
Maxiview provides a clear and unambiguous display wherever you
are on your boat.
Unlike the other ST80 display heads, the Maxiview has a key-less
facia. All user functions are controlled from the ST80 Remote
Keypad or, alternatively, a Masterview with the “Maxiview remote
control mode” chapter enabled.
Quick Reference Guide
The illustration on the following two pages provides a quick
reference guide to the complete range (Sail configuration) of the
Maxiview chapters and pages.
The Maxiview can be set to ignore the sail/power chapter and page
selections and display user-defined custom selections. For further
information on making custom selections, please refer to the Sail
and Power Selection Page.

ST80Maxiview OperationandSetup8
maxiview
maxiview
remote
Press this key momentarily to cycle
the available chapters.
Press and hold for 1 second to select
illumination adjustment. Additional
key presses change the illumination
setting.
Press this key momentarily to cycle
pages within the currently selected
chapter.
Press and hold for 1 second to return to
the previous page.
Use the arrow keys to select another
Maxiview display.
Note:
The selected Maxiview display head
changes to reverse video.
The Maxiview can also be operated
from a Masterview display.
Use the middle two keys to cycle
chapters and pages and select another
Maxiview. The key changes the key
functions from chapter/page to select.
Quick Reference Guide
maxiview
remote
remoteremote
12.5 FT
120oM
masterview
MAXIVIEW
REMOTE
masterview
MAXIVIEW
REMOTE

ST80 MaxiviewOperationandSetup 9
SPEED
CHAPTER SPEED SPEED
OVER
GROUND
VMG
TO
WIND
LOG &
TRIP
CHAPTERS PAGES
AVERAGE
SPEED MAXIMUM SPEED
NP
NAVIGATE
CHAPTER
TIMERS
CHAPTER RACE TIMER
MULTILINE
CHAPTER UP TO 8 USER DEFINED
PAGES
POSITION COG
BTW CROSS TRACK
ERROR
VMG
TO
WAYPOINT
WAYPOINT
DATA DATE TIME
TIDE
WIND
CHAPTER APPARENT WIND
SPEED
APPARENT
WIND
ANGLE
SAILING
TRUE WIND
SPEED
SAILING
TRUE WIND
ANGLE
MAGNETIC
TRUE WIND
ANGLE
NP NP NP
HEADING
CHAPTER HEADING STEER COURSE
OVER
GROUND
BEARING
TO
WAYPOINT
TACK
COURSE
NP
NP
NP
DEPTH
CHAPTER DEPTH MINIMUM
DEPTH DEPTH OFFSET
NP
NP: Page not available if the power option has been selected
Maximum Speed & Minimum Depth
The maximum speed and minimum depth displays can be reset by pressing and holding
the & keys together for 4 seconds - the display flashes during this period.
NP

ST80Maxiview OperationandSetup10
Chapter 2: Operation
2.1 General
The Maxiview operates around a chapter and page principle –
chapters are independent sections: speed, depth, wind, etc., and
pages data related to that chapter.
When the Maxiview is powered up for the first time, the unit
defaults to the SAIL configuration, unless a POWER configuration
is received via SeaTalk (refer to the Masterview setup chapter).
Operating the Maxiview using the Remote Keypad
To operate the Maxiview using the Remote Keypad, you must first
carry out the setup procedures covered in the ST80 Remote Keypad
setup chapter.
Note: SeaTalk data must be available for a chapter to function. For
example, if speed data is lost for 8 seconds, the speed chapter is
replaced by a warning screen.
Keypad Beeps
• The keypad beeps once every time a key is pressed.
• An incorrect key sequence causes the Maxiview to beep a further 2
times.
GainingControloftheMaxiview
• In order to make changes to the Maxiview displays, you must gain
control of the required Maxiview.
• Control is confirmed by the display changing to reverse video.

ST80 MaxiviewOperationandSetup 11
2.2 Speed Chapter
Boat Speed Page
This page displays your actual boat speed.
D2469-1
maxiview
remote
SPEED KNOTS
10.5
Press momentarily
to advance to the
next chapter.
Press momentarily
to advance to the
next page.
Press for 1
second to return
to the previous
page.
• The speed units are the units currently on SeaTalk: KNOTS, MPH
or KM/H.
• Trend indicators ▲or ▼are displayed if the boat speed is generally
decreasing or increasing at a rate greater than the value set in setup.
• The indicators are, by default, turned off.

ST80Maxiview OperationandSetup12
SpeedOver Ground(SOG) Page
This page displays your current speed over the ground from GPS.
D2470-1
maxiview
remote
SOG
6.5
Press momentarily
to advance to the
next chapter.
Press momentarily
to advance to the
next page.
Press for 1
second to return
to the previous
page.
KNOTS
• The speed units can be: KNOTS, MPH or KM/H.
VelocityMadeGood(VMG) to WindPage
VMG to wind displays your boat speed through the water in the
direction of true wind.
D2471-1
maxiview
remote
VMG WIND
6.3
Press momentarily
to advance to the
next chapter.
Press momentarily
to advance to the
next page.
Press for 1
second to return
to the previous
page.
KNOTS
• The units are those currently on SeaTalk: KNOTS, MPH or KM/H.
• Trend indicators ▲or ▼are displayed if the VMG is generally
decreasing or increasing at a rate greater than the value set during
calibration. The indicators are, by default, turned off.
• This page is not available if the unit is operating in POWER mode.

ST80 MaxiviewOperationandSetup 13
Log/TripPage
The Log/Trip page displays the total distance logged and a list of
trips and their current status.
D2472-1
maxiview
remote
LOG/ TRIP
LOG
TRIP 1 OFF
TRIP 2 OFF
TRIP 3 ON
TRIP 4 OFF
TRIP 5 ON
Press momentarily
to advance to the
next chapter.
Press momentarily
to advance to the
next page.
Press for 1
second to return
to the previous
page.
NM
10000.5
1000.5
1102.5
20.20
0.00
50.85
• The units are those currently on SeaTalk: NM, SM or KM.
• The trip list and the log cannot be controlled from the Maxiview.
Please refer to the Masterview handbook for trip control
information.

ST80Maxiview OperationandSetup14
Average Speed
This page displays the average boat speed for your current journey.
D2473-1
maxiview
remote
SPEED AVG
8.0
Press momentarily
to advance to the
next chapter.
Press momentarily
to advance to the
next page.
Press for 1
second to return
to the previous
page.
KNOTS
• The units are those currently on SeaTalk: KNOTS, MPH or KM/H.
• The word STOPPED is displayed if this feature is not running.
• The maximum averaging period is 24 hours.
Maximum Speed Page
This displays the maximum speed achieved during the current voyage.
D2474-1
maxiview
remote
SPEED MAX
8.5
Press
momentarily
to advance
to the next
chapter.
Press
momentarily
to advance
to the next
page.
Press for 1
second to
return to
the
previous
page.
KNOTS
Press and
hold these
keys for 4
seconds to
reset the
maximum
speed.
• The units are those currently on SeaTalk: KNOTS, MPH or KM/H.
• The display flashes for 4 seconds when the maximum speed is reset.

ST80 MaxiviewOperationandSetup 15
2.3 Depth Chapter
Depth Page
The depth page displays the current depth available on SeaTalk.
D2475-1
maxiview
remote
DEPTH FEET
Press momentarily
to advance to the
next chapter.
Press momentarily
to advance to the
next page.
Press for 1
second to return
to the previous
page.
32.5
• The displayed units are those currently on SeaTalk: FEET,
FATHOMS or METRES.
• Trend indicators ▲or ▼are displayed if the trend is generally
towards decreasing or increasing depth at a rate greater than that set
during calibration.
• The indicators are, by default, turned off.
• If the depth echo is lost the last valid echo is displayed together with
the caption “LAST ECHO”. Also, the current units are abbreviated
to FT, FA or M.

ST80Maxiview OperationandSetup16
MinimumDepth Page
D2476-1
maxiview
remote
DEPTH MIN
9.2
Press
momentarily
to advance
to the next
chapter.
Press
momentarily
to advance
to the next
page.
Press for 1
second to
return to
the
previous
page.
FT
Press and
hold these
keys for 4
seconds to
reset the
minimum
depth.
• The units are: FEET, FATHOMS or METRES.
• The time of the last echo is displayed in the 12 or 24 hour clock. This
field is deactivated if time is not available.
• The display flashes for 4 seconds when the minimum depth is reset.
Depth Offset Page
This page displays the depth transducer offset.
D2477-1
maxiview
remote
DEPTH OFFSET
-2.0
Press momentarily
to advance to the
next chapter.
Press momentarily
to advance to the
next page.
Press for 1
second to return
to the previous
page.
FT
KEEL
• The units are FEET (FT), FATHOMS (FA) or METRES (M).
• The offset can be keel, transducer or waterline – no adjustment is
possible from the Maxiview.

ST80 MaxiviewOperationandSetup 17
2.4 Wind Chapter
ApparentWindSpeed page
D2478-1
maxiview
remote
WIND APP
20.0
Press momentarily
to advance to the
next chapter.
Press momentarily
to advance to the
next page.
Press for 1
second to return
to the previous
page.
KNOTS
• The units can be : KNOTS or M/SEC.
ApparentWindAngle Page
D2479-1
maxiview
remote
WIND APP
090
Press momentarily
to advance to the
next chapter.
Press momentarily
to advance to the
next page.
Press for 1
second to return
to the previous
page.
s STBD
• The direction indicator is displayed as PORT or STBD.