Rear view safety RVS-155W User manual

Wireless Backup Camera System
with 5" Single Screen Monitor
RVS-155W
Instruction Manual

Rear View Safety
2
Introduction.............................. 03
SafetyInformation.............................. 04-06
BeforeBeginningInstallation ....................... 07-08
MonitorDimensions............................. . 09
ConnectionOptions.. .............................10
CameraDimensions...............................11
Monitor Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Camera Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
TABLE OF CONTENTS

3
NOTE! Please read all of the installation instructions
carefully before installing the product. Improper
installation will void manufacturer’s warranty.
Congratulations on purchasing a RearView Backup
Camera System!
With this manual you will be able to properly install and
operate the unit.
The Backup Camera System is intended to be installed as a
supplement aid to your standard rear view mirror that already exists
in your vehicle. The Backup Camera System should not be used as a
substitute for the standard rear view mirror or for any other mirror
that exists in your vehicle.
In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with aTV viewer or screen located forward of
the back of the driver’s seat or in any location that is visible, directly
or indirectly, to the driver while operating the vehicle.
INTRODUCTION

Rear View Safety
4
Please read the entire manual and follow the instructions and
warnings carefully. Failure to do so can cause serious damage and/or
injury, including loss of life. Be sure to obey all applicable local
trac and motor vehicle regulations as it pertains to this product.
Improper installation will void manufacturer’s warranty.
•The Rear View Camera System is
designed to help the driver safe-
ly detect people and/or objects
helping to avoid damage or injury.
However, you the driver, must use it
properly. Use of this system is not a
substitute for safe, proper or legal
driving.
•Never back up while looking at the
monitor alone. You should always
check behind and around the vehi-
cle when backing up, in the same
way as you would if the vehicle did
not have the Rear View Camera
System.Ifyoubackup whilelooking
only at the monitor, you may cause
damage or injury. Always back up
slowly.
•The Rear View Camera System is
not intended for use during exten-
sive back-up maneuvers or backing
into cross trac or pedestrian walk-
ways.
•Please, always remember, the area
displayed by the Rear View Camera
Systemis limited.It doesnotdisplay
the entire panorama that is behind
you.
USAGE:
SAFETY INFORMATION

5
•Electric shock or product
malfunction may occur if this
product is installed
incorrectly.
•Use this product within
the voltage range specied. Failure
to do so can cause
electronic shock or product
malfunction.
•Take special care when
cleaning the monitor.
•Make sure to rmly ax the prod-
uct before use.
•If smoke or a burning smell
is detected, disconnect the
system immediately.
•Where the power cable may touch
a metal case, cover the cable with
friction tape. A short circuit
or disconnected wire may cause a
re.
•While installing the Rear View
System be careful with the wire
positioning in order to avoid wire
damage.
•The Rear View System should only
be used when the vehicle is in
reverse.
•Do not watch movies or
operate the monitor while driving;
as it may cause an
accident.
•Do not install the monitor
where it may obstruct drivers
view or obstruct an air bag
device.
•Dropping the unit may cause
possible mechanical failure.
INSTALLATION:
SAFETY INFORMATION

Rear View Safety
6
IN NO EVENT SHALL SELLER OR MANUFACTURER BE
LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
SAFETY INFORMATION

7
Before drilling please check that no cable or wiring is on the other side
of the wall. Please clamp all wires securely to reduce the possibility
of them being damaged while vehicle is in use. Keep all cables away
from hot/moving parts and electrical noisy components.
We recommend doing a benchmark test before installation
to insure that all components are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)
hole should be drilled for passing camera cable through vehicles
walls. Install split grommets where applicable.
Step 3: Once all cables and wiring have been properly routed, perform
a system function test by temporarily connecting the system.
BEFORE YOU BEGIN

Rear View Safety
8
BEFORE YOU BEGIN
1. This monitor is high voltage. Only professionals should open the
monitor's case.
2. Do not watch the video while driving unless you are monitoring the
rear view camera display.
Warning!
Press "POWER ON" to turn monitor on. Press "MENU" to access main
menu. Use the arrow keys to navigate the menu and use the "MENU"
button to conrm your selection. To toggle back a screen, press
the"MENU" button.
System Operation
Instant Pair
1. Connect camera to power
2. Short press"PAIR"
3. The system will automatically pair
NOTE: Make sure camera is receiving power when pairing

9
MONITOR DIMENSIONS
Monitor Dimensions

Rear View Safety
10
CONNECTION OPTIONS
Connection Options
ME NU
MIR/NOR
PAI R
1 2 3
PUT IN TWIST &
TIGHTEN WATERPROOF
WATERPROOF CONNECTION
HARDWIRE
OR CIGARETTE LIGHTER PLUG
FEMALE TO MALE
MONITOR
CAMERA
MALE TO FEMALE
LOOSE
POWER
CABLE
LOOSE
POWER
CABLE
FEMALE PLUG
MALE PLUG

11
CAMERA DIMENSIONS
Camera Dimensions

Rear View Safety
12
MONITOR SPECIFICATIONS
Panel Size 5" LED Digital Panel
Video System NTSC / PAL Auto Detection
Resolution 480 X 3 (RGB) X272
Brightness 350 cd/m2
Contrast Ratio 500:1
Screen Mode 16:9
Field of View Top 50°, Bottom 70°, L/R 70°
Audio Output Optional; 0.5W speaker
Dot Pitch 0.077(W) × 0.231(H) mm
Active Area 110.000(W) × 62.832(H) mm
Power Input DC10-32V
Operating Temperature -20°C ~ +70°C RH 90% MAX
Storage Temperature -30°C ~ +80°C RH 90% MAX
Frequency 2400-2500MHZ
Transmission Type Digital Wireless
Transmission Range 100ft
Video Input 1 Channel
Video Source 1VP-P 75Ω
Auto Pair Yes
Power Consumption About 4W
Power Supply DC9-32V
Monitor Specications

13
CAMERA SPECIFICATIONS
Camera Specications
Sensor 1099 Color Camera
Eective Pixel Array 976 (H) X 496 (V)
Picture Elements 480,000 Pixels
NTSC Output 720 (H) X 480 (V)
PAL Output 720 (H) X 576 (V)
Optical Format 1/4 Inch
Camera Correction R=0.45-1.0
Lens F=2.5mm
Waterproof Rating IP69K
Power Consumption About 3.5W (IR On)
Power Input DC10-32V
Operating Temperature -30°C ~ +70°C RH 90% MAX
Storage Temperature -30°C ~ +80°C RH 90% MAX
Frequency 2400-2500MHZ
Transmission Type Digital Wireless
Transmission Range 100ft
Video Source 1VP-P 75Ω
S/N Ratio More Than 48DB
White Balance Auto
IR Control Auto