Rear view safety RVS-776718-BB User manual

G-SERIES Backup Camera System
with Built-In Dash Camera
RVS-776718-BB
Instruction Manual

Rear View Safety Reverse With Condence ™
2 3
NOTE! Please read all of the installation instructions
carefully before installing the product. Improper
installation will void manufacturer’s warranty.
Congratulations on purchasing a Rear View Backup
Camera System!
With this manual you will be able to properly install and
operate the unit.
The Backup Camera System is intended to be installed as a
supplement aid to your standard rear view mirror that already exists
in your vehicle. The Backup Camera System should not be used as a
substitute for the standard rear view mirror or for any other mirror
that exists in your vehicle.
In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with aTV viewer or screen located forward of
the back of the driver’s seat or in any location that is visible, directly
or indirectly, to the driver while operating the vehicle.
Introduction...............................03
SafetyInformation..........................04-06
Before Beginning Installation. . . . . . . . . . . . . . . . . . . . . . . 07
InstallationGuide.......................... 08-09
GridLines..............................10-11
InstallationandWire.........................12-14
AdjustableGridLines...........................15
MonitorSpecications..........................16
BasicFunctions...........................17-27
VideoRecording ............................28
FileBrowsing..............................29
DashCamSpecications.........................30
CameraSpecication...........................31
CameraInstallation...........................32
Troubleshooting............................33
TABLE OF CONTENTS
INTRODUCTION

Rear View Safety Reverse With Condence ™
4 5
Please read the entire manual and follow the instructions and
warnings carefully. Failure to do so can cause serious damage and/or
injury, including loss of life. Be sure to obey all applicable local
trac and motor vehicle regulations as it pertains to this product.
Improper installation will void manufacturer’s warranty.
•The Rear View Camera System is
designed to help the driver safe-
ly detect people and/or objects,
helping to avoid damage or injury.
However, you the driver, must use it
properly. Use of this system is not a
substitute for safe, proper or legal
driving.
•Never back up while looking at the
monitor alone. You should always
check behind and around the vehi-
cle when backing up, in the same
way as you would if the vehicle did
not have the Rear View Camera
System.Ifyoubackupwhile looking
only at the monitor, you may cause
damage or injury. Always back up
slowly.
•The Rear View Camera System is
not intended for use during exten-
sive back-up maneuvers or backing
into cross trac or pedestrian walk-
ways.
•Please, always remember, the area
displayed by the Rear View Camera
Systemislimited.It doesnot display
the entire panorama that is behind
you.
USAGE:
•Electric shock or product
malfunction may occur if this
product is installed
incorrectly.
•Use this product within
the voltage range specied. Failure
to do so can cause
electronic shock or product
malfunction.
•Take special care when
cleaning the monitor.
•Make sure to rmly ax the prod-
uct before use.
•If smoke or a burning smell
is detected, disconnect the
system immediately.
•Where the power cable may touch
a metal case, cover the cable with
friction tape. A short circuit
or disconnected wire may cause a
re.
•While installing the Rear View
System be careful with the wire
positioning in order to avoid wire
damage.
•The RearView System should only
be used when the vehicle is in
reverse.
•Do not watch movies or
operate the monitor while driving;
as it may cause an
accident.
•Do not install the monitor
where it may obstruct drivers
view or obstruct an air bag
device.
•Dropping the unit may cause
possible mechanical failure.
INSTALLATION:
SAFETY INFORMATION
SAFETY INFORMATION

Rear View Safety Reverse With Condence ™
6 7
IN NO EVENT SHALL SELLER OR MANUFACTURER BE
LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
A Safe Fleet Brand
Before drilling please check that no cable or wiring is on the other side
of the wall. Please clamp all wires securely to reduce the possibility
of them being damaged while vehicle is in use. Keep all cables away
from hot or moving parts and electrical noisy components.
We recommend doing a benchmark test before installation
to insure that all components are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)
hole should be drilled for passing camera cable through vehicles
walls. Install split grommets where applicable.
Step 3: Once all cables and wiring have been properly routed, perform
a system function test by temporarily connecting the system. If the
system seems to not be operating properly see troubleshooting (page
33).
SAFETY INFORMATION
BEFORE YOU BEGIN

Rear View Safety Reverse With Condence ™
8 9
Replacement Monitor
The mirror monitor replaces the existing car mirror. Carefully remove
the mirror o the“pin”. Slide the replacement mirror on to the pin and
secure it with the screw provided (already in the screw hole).Dier-
ent cars have dierent brackets. Depending on your vehicle make and
manufacturer. There are many methods to remove the original rear-
view mirror, however, please don’t force the mirror o the bracket.
The manufacturer will not be responsible for damage caused to your
car by wrong installation of the mirror. Figure 1.1
Clip-On Monitor
1. The Mirror Monitor attaches to the existing rear view mirror in
vehicle with the pressurized clips on the back of the monitor.
2. Attach monitor to existing mirror, and adjust mounting angle to
allow optimum driver viewing comfort.
Camera & Cable
Be sure to position the cable properly. The aviation camera cable uses
aircraft grade connectors which means the camera cable can be ex-
posed to all weather elements. Do not run the cable over sharp edges,
do not kink the cable and keep away from HOT and rotating parts.
Fasten all cables and secure all excess cable. Connect camera to the
camera extension cable which runs inside the vehicle. Figure 1.2
Wiring
After connecting the camera to the“camera cable”the camera should
be plugged into AV2 input. Connect the RED 12V power wire to an igni-
tion power source and the BLACK 12V ground wire to a chassis ground.
The GREEN wire is the REVERSE trigger wire. Connect this wire to the
vehicle’s backup light circuit to activate the rear-view image whenever
the vehicle shifts into reverse. To connect a second camera, connect it
to AV1 input. It can be turned on by pressing the power button on the
monitor. Figure 2.1, Figure 2.2
Precautions For Use Of Mirror Monitor
I. The Mirror Monitor is made of glass. Do not subject it to a
mechanical shock by dropping it from a high place, etc.
II. Do not apply excessive force to the monitor surface or the
adjoining areas since this may cause the color tone to vary.
III. Clean with a soft dry cloth and/or Windex only.
IV. Do not attempt to disassemble the mirror monitor.
Safety
• Before drilling, be sure no cable or wire is on the other side.
• Feed as much cable as possible into vehicle & clamp securely.
This reduces the possibility of cable being hooked or snagged.
INSTALLATION GUIDE
INSTALLATION GUIDE + TIPS

Rear View Safety Reverse With Condence ™
10 11
INSTALLATION AND WIRE
FIGURE 1.1
INSTALLATION AND WIRE
FIGURE 1.2
Dierent cars have dierent brackets. It depends on your vehicle make
and manufacturer. There are many methods to remove the original
rear view mirror, however, please don’t force the mirror o the bracket.
The manufacturer will not be responsible for any damage caused to
your car by an incorrect installation of the mirror.
When a camera is to be installed at the rear of vehicle, a good position
is usually at the top of the license plate where there is an under ledge.

Rear View Safety Reverse With Condence ™
12 13
INSTALLATION AND WIRE
INSTALLATION AND WIRE
FIGURE 2.2

Rear View Safety Reverse With Condence ™
14 15
Generally, to help drivers estimate the distance from obstacles, there are
three lines for reference- red, yellow, and green. Those three lines are dis-
played on the monitor when car is reversing. The green line is 3M from the
back of the car and the yellow line is 6.5 ft. The distant red line is 1M from
the backside of car while the close red line is 0.4M. Both reference lines on
the left and right should leave 0.2M space from the car.
The accuracy of the grid-lines can vary based on how you angle your cam-
era.Therefore to compensate for inaccuracies, you can adjust the grid-lines
to your camera angle.
GRID LINES
ADJUSTABLE GRID LINE
Accuracy
Grid Lines
Long press settings button (middle button) to enter into “grid-line ad-
justment” mode.The settings on top are for the left grid-line and the
bottom are for the right. Press the“Settings”button (middle button) to
toggle between the the two. The up, down, left and right buttons are to
adjust the location of grid-lines. The clockwise rotation buttons are to
adjust the angle of grid-lines. It is easy to operate and calibrate.

Rear View Safety Reverse With Condence ™
16 17
MONITOR SPECIFICATIONS
About Our Monitor
SPECIFICATIONS:
Screen Size:
Display Screen:
Display Resolution:
Aspect Ratio:
Color Depth:
Pixel Pitch (mm)
Power Consumption:
Working Voltage:
Video Input:
Signal System:
4.3”
TFT-LCD
400(H)x234(V)
16:9
16.7M dithering
0.219x0.219
8W
DC12V
VIDEO-IN to GPS/DVD
(Default) Camera to backup camera
PAL/Auto/NTSC
MONITOR SPECIFICATIONS
Glass and bracket
The thickness of our mirror’s glass is 4mm. It is strong enough to bear
impact and reach every country’s safety standards on rear view mirrors.
OEM bracket for special rear view mirror monitor with 21mm- thickness
pipe.
1. RED- Power (+) 2. YELLOW- Video 3. GREEN- Mirror / Normal Imaging
4. WHITE- Audio 5. BLACK- Ground (-)
FIGURE 2.1

Rear View Safety Reverse With Condence ™
18 19
Video size
Video quality
The full HD DVR mirror can record four kinds of video quality. They are HDR
1920*1080 30FPS - 1920*1080 30FPS - 1280*720 60FPS and 1280*720
30FPS. To adjust this, rst stop recording. Press“MENU”button to enter system
setting menu. Scroll to“Video Size”with the UP/DOWN buttons. Press“REC”to
choose a dierent video size.
This mirror can record videos in three qualities,“High”,“Normal”and“Low”.
Stop recording and press“MENU”button to enter into system setting menu.
Choose“Video Quality”with UP/DOWN buttons.
Press“REC”to choose a dierent video quality.
BASIC FUNCTIONS
BASIC FUNCTIONS
Language
System time
There are 10 languages available. Stop recording and press the“MENU”but-
ton twice to enter system setting menu. Scroll to“Language”with UP/DOWN
buttons. Press“REC”to choose a dierent language.
Each video le will be marked with a date and time.You can set the time to
make sure it is accurate. Stop recording and press“MENU”button twice to en-
ter system setting menu. Find“System time”and set the exact date and time
with UP/DOWN buttons. Press“REC”to switch to next setting.

Rear View Safety Reverse With Condence ™
20 21
G sensor and event recording
Turn on/Turn o/Set G-sensor
With the G-sensor function, the mirror will automatically save the video as
an“event le”when the system detects a strong acceleration, deceleration or
excessive shaking. The event le is locked and cannot be overwritten in record
cycle mode. It can only be manually deleted or formatted.The video les can
be set as event le manually. When the video is being recorded, press“MENU”
on the remote control or the lock button to activate it. This will create a
30 second event le.The event le will consist of video from 10 seconds be-
fore you press the button, and 20 seconds after.
Stop recording and press“MENU”button to enter into the video setting menu.
Find and choose“G-sensor”by pressing UP/DOWN buttons. Press“REC”to
choose a suitable sensitivity of G-sensor (High/Normal/Low/O). You can save
a maximum of 15 event le videos. The 16th event le video will overwrite the
1st one.The recommended level for the G-sensor is“Low”or“Medium”, be-
cause“High”will activate often and ll up the video capacity quickly.
BASIC FUNCTIONS
BASIC FUNCTIONS
Record recycle
Car on auto rec
This full HD DVR mirror captures every moment in high quality. The high
performance compression chip-set ensures seamless record. To ensure that it
is always recording, new recorded video will auto overwrite the pre-recorded
video when full.When record recycle is on, you can set the length of the vid-
eo les (1,3,5 min). Stop recording and press“MENU”to enter video setting
menu. Choose“Record Recycle”with the UP/DOWN buttons. Press“REC”to
choose a suitable length of recording time (1,3,5 min). Double press“MENU”
to return the recording window.
Stop recording and press“MENU”to enter video setting menu.
Enter into menu of“Car on auto rec”by pressing UP/DOWN buttons.
Press“MENU”to choose“Car on continuate rec”. The mirror will auto start to
record once mirror is turned on.

Rear View Safety Reverse With Condence ™
22 23
Diagram of Sensitivity Level
Safety Concerns of Parking Mode
What is Parking Mode?
Parking Mode
WARNING: Due to the system being on and drawing power even when the vehicle is
o, parking mode will drain the battery on your vehicle. Please be sure NOT to use this
function if you do not have a power regulator or backup power.
Parking mode means the DVR mirror can keep recording after ignition is o. When
parking mode is on, both mirror monitor and indicator are o though mirror is still
recording videos. This function can protect your car long after you leave the car. This
mirror can support parking mode for 12 hours.
BASIC FUNCTIONS
BASIC FUNCTIONS
Motion Detect
Functions of Motion Detect
When recording is stopped, press“MODE”twice to enter playback menu. Use
UP/DOWN buttons to switch between the normal video le list and the event video
le list.
As memory of the SD card is limited, you may want to only record the most import-
ant video. The motion detect setting helps with this. Recording will begin when it
detects any moving object. Choose from a variety of sensitivity levels.

Rear View Safety Reverse With Condence ™
24 25
Video Watermark - Turn On/Turn O/ Set Drive ID
Set Speed Stamp
Stop recording and press“MENU”to enter video setting menu. Find and choose“Driver
ID Setting”with the UP/DOWN buttons. Use UP/Down buttons to choose the right
number and press“REC”button to change the number.
After setting the Driver ID number, press DOWN button to nd“Driver ID stamp OSD”
choose between on/o.
Stop recording and press“MENU”to enter video setting menu. Find“Kph/Mph speed stamp
OSD”using UP/DOWN buttons. Press“REC”button to choose from Kph/Mph/O.
BASIC FUNCTIONS
BASIC FUNCTIONS
How To Set Parking Mode
Stop recording and press“MENU”to enter the video setting menu. Find and choose
“Parking Mode”using the UP/DOWN buttons. Press“REC”to set the working length
of parking mode or turn it o. Choose from 30 mins/1 hour/6 hours/12 hours/O.
Press“MENU”button to go back to the recording window, you will see a warning
message:“DVR mirror will consume a lot of electricity. Car probably cannot be
started next time. Are you sure to keep the DVR mirror working?”It is defaulted to
choose“NO”. You can choose“YES”by pressing UP/DOWN buttons.Then you will nd
another warning“Safe-guard recording mode will be activated. Please go back to
your car soon in case it cannot be started. DVR mirror consumes much electricity.
Are you sure that you want to open safe-guard recording mode?”It is defaulted to
choose“NO”. You can choose“YES”by pressing UP/DOWN buttons. After this, you can
nd the third warning message:“Safe-guard recording mode is activated. DVR mir-
ror will continue to record front views after you leave the car.”
Parking mode is now on.

Rear View Safety Reverse With Condence ™
26 27
Auto Screen O
Why do you need auto screen o function?
A bright screen can be distracting when driving at night. The mirror continues to record
even if the screen is o. It also uses less power.
Set Auto Screen O
The screen can be set to automatically turn o after a set period of inactivity. Stop record-
ing and press“MENU”twice to enter the system setting menu. Find and choose“Auto Led
O”with the UP/DOWN buttons. Press“REC”to set the time for auto screen o. You can
choose between 30 secs/1 min/2 mins/5 mins/10 mins/O. The screen will now automati-
cally turn o after reaching this set time of inactivity. The screen can also be turned on/o
manually by pressing“POWER”.
If the screen is turned on/o while recording in HDR 1920*1080 30FPS mode, recording will
stop, the current video will be saved, and a new video le will automatically start recording.
This only happens when recording in this mode.
Default setting
The system can be restored to the default settings. Stop recording and press ”MENU”twice to
enter system settings. Choose“Default Setting”using UP/DOWN. Press“REC”to select on/o,
and press“MODE”to conrm.
BASIC FUNCTIONS
BASIC FUNCTIONS
Customized set user’s name
Auto Power O
Stop recording and press“Menu”to enter the video setting menu. Using UP/DOWN but-
tons, choose“Custom name setting”. Use UP/DOWN buttons to choose the desired name
and press“REC”to make your selection.
If the mirror is not recording, it will automatically turn o after being inactive for a set
amount of time.This amount of time can be changed or turned o with the auto power
o function. Stop recording and press“MENU”to enter the video setting menu. Scroll to
“Auto power o”using UP/DOWN. Press the“REC”button to choose between 1 min/3
mins/5 mins/O.
“Driver ID”, “Speed”and“User’s Name”can all be displayed as a watermark on the record-
ed video. However, only one can be displayed at a time. The order is Driver ID, Speed and
User’s Name. If“Driver ID”is turned on,“Speed”and“User’s Name”will not be displayed
even if they are on.“Speed”will be displayed if“Driver ID”is o. If both“Driver ID”and
“Speed”are o,“User’s Name”will be displayed on the recording.
Set Speed Stamp

Rear View Safety Reverse With Condence ™
28 29
File browsing
When not recording, press“MODE”twice to enter the le browsing interface. Scroll
UP/DOWN to choose between G-Sensor les, normal les, and photos. Press“REC”to enter
a le list.
Scroll UP/DOWN to switch between videos, press“REC” to select a video, and press“REC”
again to play/pause the le. Press“MENU” to enter the delete le setting, and press“REC”
to switch between o/delete this le/delete all les. Press“MODE”to conrm.
In the le playing interface, scroll UP/DOWN to toggle between front and back videos.
Press“MODE”to return to the previous menu.
FILE BROWSING
Note:The“Delete All Files”setting can’t delete G-sensor les. G-sensor les can only be deleted manually or by
formatting the SD card.
Do not delete this file
VIDEO RECORDING
Video recording
Photograph
Press“REC”to turn video recording on/o. Press“MENU”while recording to save the
current video as an“event le”. Event les are locked and cannot be overwritten in record
cycle mode. Press“MODE”to switch the volume on or o. Press“DOWN”to save the cur-
rent frame image if the system is not recording in HDR 1920*1080 30FPS mode. When the
car is in reverse, the rear camera video will automatically display and record.
Under the stopping record mode, press“mode”can enter photograph mode, press“rec”to
photograph, and press“menu”can set the photos resolution and quality.
Note: A Class 10 SD card is recommended to ensure smooth recording
When not recording, press“MODE”to enter photography mode. Press“REC”to take a
photo, and press“MENU”to change photo resolution or image quality.

Rear View Safety Reverse With Condence ™
30 31
CAMERA SPECIFICATIONS
About Camera
SPECIFICATIONS:
MONITOR SPECIFICATIONS
Built-in Dash Cam
SPECIFICATIONS:
CPU:
Memory/Flash:
Image Sensor:
Video Resolution:
Display:
Memory:
Focus:
Photo Format:
Video Format:
Audio:
Temperature:
Power Supply:
AmbarellaA7LA30
32MB/ 1GB
CMOSOV04689-H67A
HDR1920X1080 30f/ 1920x1080 30f/
1280x720 60f/ 1280x720 30f
4.3”16:9 TFT Display
SD card (MAX32GB)
12cm-innite
JPEg
Mp4
Built in microphone and speaker
-30c°~70c°
DC 9V-32V
Certications: The DVR mirror has passed E-MARK/FCC/C-TICK and is compliant with ROHS.

Rear View Safety Reverse With Condence ™
32 33
TROUBLESHOOTINGTROUBLESHOOTING
CAMERA INSTALLATION
Camera Installation
position
170º
viewangle
installation
Mounting Position
Problems Diagnoses Solutions
Recording frequently stops 1. Motion detection is on
2. The SD card is too small to read and store information 1. Turn o motion detection
2. Use a larger higher class SD card
Camera input is working but no
1080P video is shown on screen
1. Screen is on auto-o mode
2. Auto power is turned on
1. Short press power button to turn
screen on
2. Change settings in menu
Camera input is not working and
no video on screen
1. Wiring connected improperly or broken
2. Mirror is broken
1. Reinstall with a professional
technician
2. Send system back for repairs
Mirror frozen on one interface
and will not function
1. System has been on for too long
2. Something is wrong with the system
1. Reboot
2. If this happens often, send back
for repairs
Remote does not work 1. Plastic insulation sheet not removed from battery
2. Battery is not installed correctly
3. Remote is too far from the rear view mirror
1. Remove the insulation sheet
2. Reinstall the battery
3. Keep the distance between
the remote and the mirror at 2-3 feet