Rear view safety RVS-4CAM User manual

Wireless Backup Camera System
7" Quad View Display with Built-in DVR
RVS-4CAM
Instruction Manual

Rear View Safety
2
PackageContents................................02
Introduction..................................03
SafetyInformation..............................04-06
Before Beginning Installation . . . . . . . . . . . . . . . . . . . . . . . 07
Precautions.......................... . . . . 08
Monitor Specication..............................09
MonitorButtons.................................10
CameraSpecication...............................11
SystemPlacement................................12
Connection................. . . . . . . . . . . . . . 13
UserInterface.......................... . . . . 14-16
TABLE OF CONTENTS
1 x Color CCD Infra-Red Weatherproof Wireless Backup Camera
1 x 7" Quad View Monitor With Built-In DVR and Sunshade
1 x Universal Mount With Adhesive Pad
3 x Wireless Antennas
1 x Remote Control
1 x Camera Power Cable
1 x Screw Kit for Camera Installation
TABLE OF CONTENTS
In The Box For Standard RVS-4CAM

3
NOTE! Please read all of the installation instructions
carefully before installing the product. Improper
installation will void manufacturer’s warranty.
Congratulations on purchasing a RearView Backup
Camera System!
With this manual you will be able to properly install and
operate the unit.
The Backup Camera System is intended to be installed as a
supplement aid to your standard rear view mirror that already exists
in your vehicle. The Backup Camera System should not be used as a
substitute for the standard rear view mirror or for any other mirror
that exists in your vehicle.
In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with aTV viewer or screen located forward of
the back of the driver’s seat or in any location that is visible, directly
or indirectly, to the driver while operating the vehicle.
INTRODUCTION

Rear View Safety
4
Please read the entire manual and follow the instructions and
warnings carefully. Failure to do so can cause serious damage and/or
injury, including loss of life. Be sure to obey all applicable local
trac and motor vehicle regulations as it pertains to this product.
Improper installation will void manufacturer’s warranty.
•The Rear View Camera System is
designed to help the driver safe-
ly detect people and/or objects
helping to avoid damage or injury.
However, you the driver, must use it
properly. Use of this system is not a
substitute for safe, proper or legal
driving.
•Never back up while looking at the
monitor alone. You should always
check behind and around the vehi-
cle when backing up, in the same
way as you would if the vehicle did
not have the Rear View Camera
System.Ifyoubackupwhilelooking
only at the monitor, you may cause
damage or injury. Always back up
slowly.
•The Rear View Camera System is
not intended for use during exten-
sive back-up maneuvers or backing
into cross trac or pedestrian walk-
ways.
•Please, always remember, the area
displayed by the Rear View Camera
Systemislimited.Itdoes notdisplay
the entire panorama that is behind
you.
USAGE:
SAFETY INFORMATION

5
•Electric shock or product
malfunction may occur if this
product is installed
incorrectly.
•Use this product within
the voltage range specied. Failure
to do so can cause
electronic shock or product
malfunction.
•Take special care when
cleaning the monitor.
•Make sure to rmly ax the prod-
uct before use.
•If smoke or a burning smell
is detected, disconnect the
system immediately.
•Where the power cable may touch
a metal case, cover the cable with
friction tape. A short circuit
or disconnected wire may cause a
re.
•While installing the Rear View
System be careful with the wire
positioning in order to avoid wire
damage.
•The Rear View System should only
be used when the vehicle is in
reverse.
•Do not watch movies or
operate the monitor while driving;
as it may cause an
accident.
•Do not install the monitor
where it may obstruct drivers
view or obstruct an air bag
device.
•Dropping the unit may cause
possible mechanical failure.
INSTALLATION:
SAFETY INFORMATION

Rear View Safety
6
IN NO EVENT SHALL SELLER OR MANUFACTURER BE
LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
SAFETY INFORMATION

7
Before drilling please check that no cable or wiring is on the other side
of the wall. Please clamp all wires securely to reduce the possibility
of them being damaged while vehicle is in use. Keep all cables away
from hot/moving parts and electrical noisy components.
We recommend doing a benchmark test before installation
to insure that all components are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)
hole should be drilled for passing camera cable through vehicles
walls. Install split grommets where applicable.
Step 3: Once all cables and wiring have been properly routed, perform
a system function test by temporarily connecting the system.
BEFORE YOU BEGIN

Rear View Safety
8
Operating Precautions
1. The device may be powered by a 12/24 volt battery or the vehicle's
electrical system.
2. Make sure all cables are connected properly. Improper cable connec-
tions may damage the monitor. Remove the power cable connections
when not using the device.
3. The back-up battery may be recharged when the power is on.
4. When battery is fully charged, recharging will automatically stop.
5. If batteries are not used for a while, it may take longer to charge.
1. This monitor is high voltage. Only professionals should open the
monitor's case.
2. Do not watch the video while driving unless you are monitoring the
rear view camera display.
Special Note
Occasionally, a few highlights or dark spots may appear on the LCD screen. This
doesn’t necessarily indicate any monitor defects. Never try to repair this device
yourself. If any problems occur, immediately turn the display o and notify our
company or an authorized dealer. Any disassembly or modication may lead to
damage and will also void the warranty.
PRECAUTIONS
Warning!

9
Monitor Specication
• Supports both NTSC and PAL video systems
• Supports 4 cameras with 3 trigger wires. Image automatically
switches to respective camera once trigger is activated
• Display eect/volume can be changed for each individual camera
• Grid lines (can be switched on/o)
• Optional recording function
• 7" digital monitor with touch screen/keys
• Resolution: 800 x 3 RGB x 480
• Contrast: 300:1
• Brightness: 350cd/m2
• Input voltage: DC12-24V
• Power consumption: <500mA
• Operating temperature: -20°C ~ 70°C
• Storage temperature: -30°C ~ 80°C
MONITOR SPECIFICATION

Rear View Safety
10
Monitor Buttons
MONITOR BUTTONS
Menu/Select

11
Camera Specication
CAMERA SPECIFICATION
Camera Type 1/4"Sharp®Color CCD
Picture Elements 250,000 pixels
Gamma Correction r=0.45 to 1.0
Viewing Angle 130°
Image Sensor 540 TV lines PAL: 752 (H) x 582 (V), NTSC: 769 (H) x 494 (V)
Lens 2.1mm
Waterproof Rating IP68
View Angle 130°
Sync System Internal Synchronization
Infra-red Distance 50 Feet (9 Infrared)
Usable Illumination 0 Lux (IR On)
Power Source DC 12V/3A (+/- 10%)
S/N Ratio More than 48dB
Electronic Iris 1/50, 160-1/100,000sec
Video Output 1Vp.p 75Ω
IR Switch Control ACDS Automatic Control
Vibration and Shock Rating 20G / 100G
Operating Temperature -30°C ~ +80°C / RH 95% Max
Storage Temperature -30°C ~ +60°C / RH 95% Max

Rear View Safety
12
MONITOR AND CAMERA PLACEMENT
Placement

13
CONNECTION
1. The monitor will automatically turn on when connected to a power
source. If it is not connected to a camera, it will automatically turn o
after 3 seconds.
2. Image will automatically appear on the screen when a trigger is
activated.
3. Grid lines can be turned ON/OFF.
SAFETY NOTICE
This system is designed as a driver's aid.
Just using a backup camera will not completely erase a vehicle's blind spots.
OPERATION GUIDE
Transmitter for optional side camera

Rear View Safety
14
USER INTERFACE
1. On the monitor press "MENU" button then select
"SETTING" "PAIR CAMERA"
2. Press the "PAIR" button on the camera/transmitter
3. On the monitor select the desired camera, it will pair automatically
4. "PAIR OK" will appear on the screen after a sucessful pairing. If
"TIME OUT" displays, try pairing again

15
USER INTERFACE
Image
Reversal
select

Rear View Safety
16
USER INTERFACE
Setting
select