Rear view safety RVS-8106131N User manual

Reverse With Condence ™ 1
Backup Camera System
With Waterproof Monitor and Shutter Camera
RVS-8106131N
Instruction Manual

Rear View Safety
2
Introduction.............................. 03
SafetyInformation.............................. 04-06
BeforeBeginningInstallation ....................... 07
Precautions.......................... . 08
Monitor..............................09-10
Wiring.................................11
MonitorMenuOperation...........................12 -14
Camera Specications . . . . . . . . . . . . . . . . . . . . . . . . 15
Camera Dimensions......................... . . . 16
TABLE OF CONTENTS

Reverse With Condence ™ 3
NOTE! Please read all of the installation instructions
carefully before installing the product. Improper
installation will void manufacturer’s warranty.
Congratulations on purchasing a RearView Backup
Camera System!
With this manual you will be able to properly install and
operate the unit.
The Backup Camera System is intended to be installed as a
supplement aid to your standard rear view mirror that already exists
in your vehicle. The Backup Camera System should not be used as a
substitute for the standard rear view mirror or for any other mirror
that exists in your vehicle.
In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with aTV viewer or screen located forward of
the back of the driver’s seat or in any location that is visible, directly
or indirectly, to the driver while operating the vehicle.
INTRODUCTION

Rear View Safety
4
Please read the entire manual and follow the instructions and
warnings carefully. Failure to do so can cause serious damage and/or
injury, including loss of life. Be sure to obey all applicable local
trac and motor vehicle regulations as it pertains to this product.
Improper installation will void manufacturer’s warranty.
•The Rear View Camera System is
designed to help the driver safe-
ly detect people and/or objects
helping to avoid damage or injury.
However, you the driver, must use it
properly. Use of this system is not a
substitute for safe, proper or legal
driving.
•Never back up while looking at the
monitor alone. You should always
check behind and around the vehi-
cle when backing up, in the same
way as you would if the vehicle did
not have the Rear View Camera
System.Ifyoubackupwhilelooking
only at the monitor, you may cause
damage or injury. Always back up
slowly.
•The Rear View Camera System is
not intended for use during exten-
sive back-up maneuvers or backing
into cross trac or pedestrian walk-
ways.
•Please, always remember, the area
displayed by the Rear View Camera
Systemis limited.Itdoes notdisplay
the entire panorama that is behind
you.
USAGE:
SAFETY INFORMATION

Reverse With Condence ™ 5
•Electric shock or product
malfunction may occur if this
product is installed
incorrectly.
•Use this product within
the voltage range specied. Failure
to do so can cause
electronic shock or product
malfunction.
•Take special care when
cleaning the monitor.
•Make sure to rmly ax the prod-
uct before use.
•If smoke or a burning smell
is detected, disconnect the
system immediately.
•Where the power cable may touch
a metal case, cover the cable with
friction tape. A short circuit
or disconnected wire may cause a
re.
•While installing the Rear View
System be careful with the wire
positioning in order to avoid wire
damage.
•The Rear View System should only
be used when the vehicle is in
reverse.
•Do not watch movies or
operate the monitor while driving;
as it may cause an
accident.
•Do not install the monitor
where it may obstruct drivers
view or obstruct an air bag
device.
•Dropping the unit may cause
possible mechanical failure.
INSTALLATION:
SAFETY INFORMATION

Rear View Safety
6
IN NO EVENT SHALL SELLER OR MANUFACTURER BE
LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
SAFETY INFORMATION

Reverse With Condence ™ 7
Before drilling please check that no cable or wiring is on the other side
of the wall. Please clamp all wires securely to reduce the possibility
of them being damaged while vehicle is in use. Keep all cables away
from hot/moving parts and electrical noisy components.
We recommend doing a benchmark test before installation
to insure that all components are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)
hole should be drilled for passing camera cable through vehicles
walls. Install split grommets where applicable.
Step 3: Once all cables and wiring have been properly routed, perform
a system function test by temporarily connecting the system.
BEFORE YOU BEGIN

Rear View Safety
8
PRECAUTIONS
1. This monitor is high voltage. Only professionals should open the
monitor's case.
2. Do not watch the video while driving unless you are monitoring the
rear view camera display.
Warning!

Reverse With Condence ™ 9
MONITOR
Monitor Introduction
Monitor Dimensions (mm)

Rear View Safety
10
MONITOR
Sunshade Installation
U-Bracket Installation

Reverse With Condence ™ 11
WIRING
Wiring
1. Camera 1 (white)
2. Camera cable
3. Camera 1 trigger wire (white)
4. Camera 2 trigger wire (blue)
5. Car power input: DC11-32V
6. Camera 2 (blue)
7. Camera cable (second camera/cable sold seperately)

Rear View Safety
12
MENU OPERATION
Menu Operation
Press "Menu" and the monitor will display the following options:
Bright/Contrast/Color/Delay Time/Language/Zoom/Mirror.
Press left/right to adjust brightness/color and contrast (1-100).
Bright/Contrast/Color

Reverse With Condence ™ 13
MENU OPERATION
Delay Time
Press left/right to adjust trigger delay (1-30sec).
This option can be set for two cameras (2nd camera sold seperately).
Language

Rear View Safety
14
MENU OPERATAION
Zoom (Display Mode)
Once in the Zoom option, press left/right to toggle display mode.
Monitor Specications

Reverse With Condence ™ 15
Camera Specications
CAMERA SPECIFICATIONS
Camera 1/3" Sharp® CCD
TV System PAL/NTSC
Eective Pixels 512 x 582 pixels / 512 x 492 pixels
Sensing Area 4.9 mm (H) x 3.7 mm (V)
Viewing Angle 120°
Scanning System 2:1 Interlace
Sync. System Internal
Resolution 600 TV Lines
Horizontal Sync. Frequency 15.625 KHz / 15.734 KHz
Minimum Illumination 0.1 Lux (day), 0 Lux (With IR)
Microphone Yes
Video Output 1.0 vp-p, 75 Ohm
Gamma Consumption 0.45
AGC Auto
Waterproof Rating IP69K
S/N Ratio Better Than 48 dB
White Balance Auto
Waterproof Rating IP69K
Electric Shutter 1/60 (NTSC) / 1/50 (PAL)
~ 1/10,000 Seconds
BLC Auto
Current Consumption Max. 230 mA
Power Supply DC 12V

Rear View Safety
16
CAMERA SPECIFICATIONS
Camera Dimensions
• Motorized shutter: Automatically moves to protect lens
• IP69K Rating: Completely waterproof
• 120° Viewing Angle: Ultra wide, all encompassing view
• Built-in high gain microphone
CAMERA DIMENSIONS