Regency Fireplace Products Grandview G800C Quick start guide

920-182j FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4 11.08.22
Grandview®G800C
Gas Fireplace
Owners &
Installation Manual
www.regency-re.com
MODEL: G800C
Medium DV Gas Fireplace
Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch: do not use any phone in your building.
Leave the building immediately.
• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the re department.
Installation and service must be performed by a qualied installer, service agency or the gas supplier.
Installer: Please complete the details on the back cover and leave
this manual with the homeowner.
Homeowner:Please keep these instructions for future reference.
Certied to/Certié pour: ANSI Z21.88-2019
Tested by:
Warning
Fire or Explosion Hazard
Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.

2 | Grandview®G800C Gas Fireplace
920-408
4.34.7
Instruction Plate
For a glass-fronted gas appliance where the temperature of the glass
viewing area outside surface exceeds the limits specified in Clause 5.14.4, the following
graphic danger and statements shall be shown on a Class IIIA-2 Permanent Label.
4.34.6
Instruction Plate
Each appliance shall bear a Class IIIB marking with letters on a contrasting background, located
adjacent to the controlling device or in an equally conspicuous position where the instruction can be easily read.
April 22/14: Created draft
Double sided
Material: Synthetic Paper
Size 5.965" W x 5.71" H
Color: As shown in artwork
DANGER
HOT GLASS WILL
CAUSE BURNS
DO NOT TOUCH GLASS
UNTIL COOLED
NEVER ALLOW CHILDREN
TO TOUCH GLASS
A barrier designed to reduce the risk of burns from the hot viewing glass
is provided with this appliance and must be installed for the protection
of children and other at risk individuals.
!DANGER
!
920-408
CAUTION:
HOT WHILE IN OPERATION. DO NOT TOUCH.
SEVERE BURNS MAY RESULT. KEEP CHILDREN, CLOTHING, FURNITURE,
GASOLINE, AND ANY OTHER LIQUIDS WITH FLAMMABLE VAPOURS AWAY.
KEEP BURNER AND CONTROL COMPARTMENT CLEAN.
SEE INSTALLATION AND OPERATING INSTRUCTIONS ACCOMPANYING
APPLIANCE.
Front Back
LA SURFACE VITRÉE CHAUDE
PEUT CAUSER DES BRÛLURES.
NE TOUCHEZ PAS À LA
SURFACE VITRÉE NON REFROIDIE.
NE LAISSEZ JAMAIS UN
ENFANT TOUCHER LA SURFACE
VITRÉE.
DANGER
!
L’écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de
contact accidentel avec la vitre chaude et doit être installé pour la protection des
enfants et des personnes à risque.
920-408-fr
ATTENTION
S'assurer que le brûleur et le compartiment des commandes sont propres.
Voir les instructions d’installation et d’utilisation qui accompagnent
l'appareil.
Risque de brûlures graves.
Ne pas toucher l’appareil lorsqu’il fonctionne.
Ne pas laisser les enfants s’approcher de l’appareil. Garder les
vêtements, les meubles et tout gaz ou liquide inflammable (carburant)
à distance de l'appareil.
To the New Owner:
Congratulations!
You are the owner of a state-of-the-art Gas Fireplace by REGENCY®. The Grandview™ G800C has been designed to provide
you with all the warmth and charm of a wood replace at the ick of a switch. The Grandview™ G800C has been approved
by Intertek for both safety and eciency. As it also bears our own mark, it promises to provide you with economy, comfort
and security for many trouble free years to follow. Please take a moment now to acquaint yourself with these instructions and
the many features of your Regency®Fireplace.

Grandview®G800C Gas Fireplace | 3
MANUFACTURED MOBILE HOME REQUIREMENTS
INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE
This Regency® product has been tested and listed by Intertek as a Direct Vent Wall Furnace to the following
standards: Vented Gas Fireplace Heaters ANSI Z21.88-2019.
This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions
and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard
of Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A.
This appliance installation must comply with the manufacturer's installation instructions and local codes, if any.
In the absence of local codes follow the current National Fuel Gas Code, ANSI Z223.1 and the current National
Electrical Code ANSI/NFPA 70 in the U.S.A.
This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel
chassis as applicable to local codes.
The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of
local codes, with the National Electrical Code, ANSI/NFPA 70.
This appliance may only be installed in an aftermarket permanently located, manufactured (U.S.A only) or mobile
home, where not prohibited by local codes.
This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible
for use with other gases.
Ensure that structural members are not cut or weakened during installation.
This appliance may be installed in an aftermarket permanently
located, manufactured (U.S.A. only) or mobile home, where
not prohibited by local codes.
This appliance is only for use with the type of gas indicated
on the rating plate. A conversion kit is supplied with the
appliance.

4 | Grandview®G800C Gas Fireplace
WARNING
CARBON MONOXIDE POISONING HAZARD
Failure to follow the steps outlined below for each appliance connected to the venting
system being placed into operation could result in carbon monoxide poisoning or death.
The following steps shall be followed for each appliance connected to the venting system
being placed into operation, while all other appliances connected to the venting system are
not in operation:
1. Seal any unused openings in the venting system.
2. Inspect the venting system for proper size and horizontal pitch, as required in the
National Fuel Gas Code, ANSI Z223.1/NFPA 54.1 and these instructions.
Determine that there is no blockage or restriction, leakage, corrosion and other
deficiencies which could cause an unsafe condition.
3. As far as practical, close all building doors and windows and all doors between the
space in which the appliance(s) connected to the venting system are located and other
spaces of the building.
4. Close fireplace dampers.
5. Turn on clothes dryers and any appliance not connected to the venting system. Turn on
any exhaust fans, such as range hoods and bathroom exhausts, so they are operating at
maximum speed. Do not operate a summer exhaust fan.
6. Follow the lighting instructions. Place the appliance being inspected into operation.
Adjust the thermostat so appliance is operating continuously.
7. Test for spillage from draft hood equipped appliances at the draft hood relief opening
after 5 minutes of main burner operation. Use the flame of a match or candle.
8. If improper venting is observed during any of the above tests, the venting system must
be corrected in accordance with National Fuel Gas Code, ANSI Z223.1/NFPA.
9. After it has been determined that each appliance connected to the venting system
properly vents when tested as outlined above, return doors, windows, exhaust fans,
fireplace damper and any other gas-fired burning appliance to the previous
conditions of use.
Other considerations:
Non-metallic venting systems shall not interchange components with another listed or unlisted metallic
venting system.

Grandview® G800C Gas Fireplace | 5
table of contents
Owner's Information Venting Arrangements with Co-linear Flex System into a Masonry
Chimney Application.................................................................... 58
Venting Arrangement - Vertical Terminations - Co-linear Flex
System Into Masonry Fireplaces ................................................ 59
Unit Installation with Horizontal Termination ................................. 60
Unit Installation with Vertical Termination...................................... 61
Direct Vent System (Flex) Installation Procedures .......................... 62
Vertical Termination 4" x 6-7/8" (102 mm x 175 mm) Venting
- Vertical Flex Vent Kit (Part #946-755)....................................... 63
Vertical Flue Extension Kit (Part #946-756) ................................... 64
Ceiling Firestop / Firestop Spacer (Part #946-757)......................... 64
Conversion from NG to LP using SIT Gas Valve.............................. 65
Brick Panel installation................................................................. 67
Enamel/Steel Panel Installation .................................................... 68
Log Set Installation ..................................................................... 69
Crystal Tray Installation ............................................................... 73
Driftwood Media Kit Installation.................................................... 74
Pilot Adjustment.......................................................................... 76
S.I.T. 820 Valve Description.......................................................... 76
NG System Data ......................................................................... 76
LP System Data .......................................................................... 76
Gas Pipe Pressure Testing ............................................................ 76
Aeration Adjustment.................................................................... 77
Electrical Access and Installation .................................................. 77
Optional Wall Thermostat (Part # 910-407)................................... 78
Optional Remote Control (Part # 946-704).................................... 78
Optional Wall Switch (Not Supplied by Regency)............................ 78
Installing an Optional Wall Switch (Not Supplied by Regency) or
Thermostat (Part # 910-407 or 910-404/P)................................. 79
Wiring Diagram With and Without Thermostat/Remote Control....... 80
Installing the Optional Fan (Part 761-979)..................................... 81
Fan Install After Unit Installation .................................................. 82
Fan Wall Control Installation Kit (Part # 761-974).......................... 83
Optional On/O Remote Kit Installation (Part # 946-704)............... 85
Safety Screen Removal ................................................................ 86
Safety Screen Installation ............................................................ 86
Glass Door Removal .................................................................... 86
Glass Door Installation................................................................. 86
Operating Instructions................................................................. 87
First Fire..................................................................................... 87
Normal Operating Sounds of Gas Appliances ................................. 87
Receiver Battery Replacement ...................................................... 88
DC Spark Igniter Battery Installation/Replacement......................... 88
Copy of Lighting Plate Instructions ............................................... 89
Maintenance Instructions............................................................. 90
General Vent Maintenance ........................................................... 90
Log Replacement ........................................................................ 90
Glass Gasket ............................................................................... 90
Door Glass.................................................................................. 90
Glass Replacement ...................................................................... 90
Valve Replacement ...................................................................... 91
Gas Appliance Maintenance.......................................................... 92
Main Assembly............................................................................ 93
Optional Accessories.................................................................... 95
Warranty ...............................................................................96
Copy of Safety Decal ..................................................................... 6
Decal Location .............................................................................. 6
Unit Dimensions............................................................................ 8
Before You Start.......................................................................... 11
Important Message .................................................................... 12
General Safety Information .......................................................... 12
To Turn Appliance On/O............................................................. 12
Optional Fan Operation................................................................ 12
Lighting the Pilot Using the Gas Control Knob Extender.................. 13
Proame I Remote Control Operating Instructions ......................... 14
Proame I Remote Receiver Battery Replacement.......................... 17
Operating Procedure for Remote Control....................................... 18
Safety Screen Removal ................................................................ 19
Safety Screen Installation ............................................................ 19
Glass Door Removal .................................................................... 19
Glass Door Installation................................................................. 19
Gas Installation Checklist ............................................................... 9
Installation Checklist.................................................................... 20
Locating Your Gas Fireplace ......................................................... 20
HeatWave Duct System Optional Kit #946-556.............................. 20
Clearance / Framing and Venting Congurations............................ 21
Cool Wall Installation (Combustible Finishing)................................ 22
Non-Combustible Installation ....................................................... 22
Cool Wall installation/Cool Wall Conversion.................................... 23
Cool Wall Clearances ................................................................... 24
Cool Wall Mantel Clearances........................................................ 25
Cool Wall Mantel Leg Clearances .................................................. 25
Cool Wall Installation - Framing.................................................... 26
Chase Venting............................................................................. 27
Chase Vent Installation - Cool Wall .............................................. 28
Clean Front Installation (Non Cool Wall) - Clearances..................... 29
Clean Front Installation (Non Cool Wall)—Mantel Clearances .......... 30
Clean Front Installation (Non Cool Wall) - Mantel Leg Clearances.... 31
Clean Front Installation (Non Cool Wall) - Non Combustible
Requirements ........................................................................... 31
Clean Front Installation - Framing (Non Cool Wall)......................... 32
Clean Front Installation................................................................ 33
Nailing Flange Instructions........................................................... 33
Optional Clean Front Trim Install Instructions ................................ 33
Outside Finish Installation (Non Cool Wall) - Clearances ................. 34
Outside Finish Installation (Non Cool Wall) - Mantel Clearances ...... 35
Outside Finish Installation (Non Cool Wall) - Mantel Leg
Clearances................................................................................ 35
Outside Finish Installation (Non Cool Wall)- Framing...................... 36
Outside Finish - Finishing ............................................................ 37
Faceplate Install (Part # 761-922, 761-924, 761-926).................... 38
Finishing Trim Install (Part # 761-928).......................................... 40
Unit Assembly Prior to Installation ................................................ 42
Nailing Flange Installation............................................................ 43
Wall Board/Drywall Installation..................................................... 44
Conversion to Top Vent................................................................ 45
Vent Restrictor Installation........................................................... 47
Venting Introduction.................................................................... 47
Exterior Vent Termination Requirements........................................ 48
4" X 6-5/8" (102 mmx 168 mm) Rigid Pipe - Cross Reference
Chart Only ................................................................................ 49
Venting Arrangements - Horizontal Termination - Rigid Pipe and
Direct Vent System (Flex) ......................................................... 53
Venting Arrangements - Vertical Termination - Rigid Pipe System
and Vertical Flex Kit to Same Limitations..................................... 54
Horizontal Terminations - Two 90°Elbows ..................................... 55
Horizontal Terminations - Three 90oElbows .................................. 55
Vertical Venting with Two 90oElbows ............................................ 56
Vertical Venting with Three 90oElbows ...................................... 56
Vertical Terminations Three 90° Elbows - Rigid Pipe 4" x 6 - 5/8"
(102 mm x 168 mm) ................................................................. 57
Installer's Information
Installation
Maintenance
Parts List
Operating Instructions

6 | Grandview®G800C Gas Fireplace
owner's information
This is a copy of the label that accompanies each Grandview™ G800C Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review.
NOTE: Regency® units are constantly being improved. Check the label on the unit and if there is a dierence, the label on the unit is the correct one.
Copy of Safety Decal
For the State of Massachusetts, installation
and repair must be done by a plumber or
gas tter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, exible con-
nectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appli-
ances individual manual shut-o must be a
t-handle type valve.
The State of Massachusetts requires the
installation of a carbon monoxide alarm in
accordance with NFPA 720 and a CO alarm
with battery back up in the same room where
the gas appliance is installed.
Decal Location
DO NOT REMOVE DECAL FROM UNIT.
Remove bottom cover—decal will
be on the oor of the unit
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE
536
536
DOOR SEAL: Please
check that the door is
properly sealed
FPI Fireplace Products International Ltd.
Delta, BC, Canada
Minimum Clearances to Combustibles / Rear Vent—Clean Finish
Dégagements minimaux par rapport aux matériaux combustibles
Serial No./ No de série
920-168d
Electrical supply/Alimentation électrique 115VAC, 1.5A, 60Hz.
VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUELS. CATEGORY I
NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE. CATÉGORIE I FOYER AU GAZ À ÉVACUATION - Made in Canada/ Fabriqué au Canada
Duplicate S/N
0" Clearance to
combustibles from /
Top, sides, bottom and rear of unit
Mantel Clearances from
Fireplace Opening /
(A) 20-1/2" (521 mm) at max. depth
Side Wall Clearance
from Fireplace Opening /
B) Min. 26-1/2" (673mm)(on one side)
Ceiling from Top of
Fireplace Opening:
C) Min. 36-1/2" (927 mm)
Mantel Depth:
D) Max. 19" (483 mm)
Alcove Clearances:
E) Min. Width 84" (2134 mm),
F) Max. Depth 36" (914 mm)
Minimum Vent Clearances:
Horizontal Top 2" (51 mm)
Horizontal Side 1-1/2" (38 mm)
Horizontal Bottom 1-1/2" (38 mm)
Vertical Vent 1-1/2" (38 mm)
(See Instruction Manual for detailed instructions)
APPAREIL FONCTIONNANT AU GAZ PROPANE
Modèle -LPG800C
PROPANE GAS: Model G800C-LP
NATURAL GAS: Model G800C-NG
Minimum supply pressure
Manifold pressure high
Manifold pressure low
Orifice size
Minimum input
Maximum input
Altitude
Pression d'alimentation minimale
Pression manifold - haute
Pression manifold - basse
Taille de l'orifice
D bit calorifique minimal é
D bit calorifique maximalé
Altitude
5.0" WC/C.E. (1.25 kPa)
3.8" WC/C.E. (0.94 kPa)
1.1" WC/C.E. (0.27 kPa)
# 42 DMS
15,000 Btu/h (4.4 kW)
27,000 Btu/h (7.91 kW)
0-4500 ft/pi (0-1372 m)
Part #: 920-168d
Colour: Everything black on grey except what is highlighted is printed red.
Size: File@100% 9.117’’W x 6.045’’H
Nov. 1/19 : Created Draft
Jan 6, 2020: Removed reference to CSA standard
Mar. 17/21: Updated CSA/ANSI date
Sept. 16/21:Update P.4.1 data
Jan 25/22: Added Category 1
July 4/22: Changed wording
Pression d'alimentation minimale
Pression manifold - haute
Pression manifold - basse
Taille de l'orifice
D bit calorifique minimalé
D bit calorifique maximalé
Altitude
11" WC/C.E. (2.74 kPa)
10.5" WC/C.E. (2.61 kPa)
2.9" WC/C.E. (0.72 kPa)
# 53 DMS
14,500 Btu/h (4.25 kW)
26,500 Btu/h (7.77 kW)
0-4500 ft/pi (0-1372 m)
Minimum supply pressure
Manifold pressure high
Manifold pressure low
Orifice size
Minimum input
Maximum input
Altitude
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1.
This appliance must be installed in accordance with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States, or when such a standard is not applicable,
ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured (mobile) home where not prohibited by local codes. See
owner's manual for details. This appliance is not convertible for use with other gases, unless a certified kit is used. (Kit #761-977). Fan Part # 761-979.
Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1. Installer l'appareil selon la norme 24 CFR, Part 3280, Manufactured Home
Construction and Safety Standard. Si ces normes ne sont pas pertinentes, utilisez la norme ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C
Standard for Recreational Vehicles. Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison préfabriquée ou mobile (É.-U.
seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de
conversion certifiée est fournie.
This vented gas fireplace heater is not for use with air filters. Ne pas utiliser de filtre à air avec ce foyer au gaz à évacuation.
FOR USE WITH GLASS DOORS CERTIFIED WITH THE APPLIANCE ONLY POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE CERTIFIÉES AVEC L'APPAREIL
For Use Only with Barrier (Part #761-038/P ) Utiliser uniquement avec l’écran ( n ° 761-038/P )
E
B
A
C
D
F
C #: 4001172
MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE.
Listed/Nom: Vented Gas Fireplace Heater / Foyer au Gaz à Évacuation
Certified to/Certifi pour: é ANSI Z21.88-2019
Refer to Intertek's Directory of Building Products for detailed information.
Pour plus de détails , se reporter au Répertoire des produits de construction de Intertek.
APPAREIL FONCTIONNANT AU GAZ NATUREL
Modèle G800C-NG
CSA P.4.1 Fireplace Efficiency (FE) /Efficacité énergétique des foyers (EEF) CSA P.4.1
Natural Gas / Gaz naturel 54.17%
Propane Gas / Gaz propane 53.64%
CANADIAN ENERGY
PERFORMANCE
VERIFIED
RENDEMENT
ÉNERGÉTIQUE
VÉRIFIÉ
EP5011169

Grandview® G800C Gas Fireplace | 7
owner's information
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shallobserve that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a batteryoperated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipmentat the completion of
the installation.
MA Code - CO Detector
(for the State of Massachusetts only)

8 | Grandview®G800C Gas Fireplace
owner's information
Unit Dimensions
ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.
ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.
42 7
8
"
1088mm
35 7
8
"
913mm
OUTSIDE FINISH
30 7
8
"
783mm
CLEAN FRONT
32 5
8
"
827mm
CLEAN FRONT
1 5
8
"
41mm
33 7
8
"
862mm
OUTSIDE FINISH
1 5
8
"
41mm
29 7
8
"
759mm
25 1
2
"
648mm
36 3
8
"
924mm
35 1
8
"
892mm
18 7
8
"
480mm
17 1
2
"
446mm
7 1
2
"
192mm
1 1
2
"
39mm
28 7
8
"
734mm
11 1
4
"
287mm
11 1
4
"
287mm
ELECTRICAL
INLET
4"
101mm
65
8
"
170mm
18"
457mm
19"
481mm
NON COOL WALL
16 7/8"
429mm
COOL WALL
7 5
8
"
195mm
1 1
4
"
32mm
32 1
2
"
823mm
FIREPLACE OPENING
GAS INLET
37 3
4
"
959mm
34 3
4
"
883mm
37 1
2
"
953mm
34 5
8
"
880mm
Finishing Trim Faceplate
29''
(737mm)
Note: Gas connection is from the left hand side of the appliance & electrical connection on right hand side of the appli-
ance. A metal receptacle box is supplied/installed with the appliance to make all 120 volt electrical connections.

Grandview®G800C Gas Fireplace | 9
dimensions
05/18/21
1
REGENCY GAS INSTALLATION CHECKLIST
Customer: Date Installed:
Install Address: Location of Fireplace:
Serial No: Installer:
Model No:
Site Requirements YES NO
If applicable, are the insulation, vapour barrier, and drywall present if installed on an outside wall or chase?
Does the area have a solid continuous base to support the unit?
Will the area accommodate the size of the applliance and all clearances?
Are the gas and electrical roughed into the area where the unit is being installed?
In City & Grandview series cool wall applications, is the chase enclosure sealed to prevent heat from escaping? All hot air
from the unit must exit via the mandatory ventilation openings.
In City & Grandview applications, Is the chase enclosure vented with the mandatory heat ventilation openings? See manual
for details.
If applicable, is the masonry/factory built freplace in its original condition with no modifications?
If applicable, have the hearth requirements been met?
Unit Setup YES NO
If applicable, are the standoffs and top nailing flange extensions installed and at the correct depth to accommodate finishing
material? See manual for details.
If applicable, is the fireplace level and secured, meeting framing clearances? See manual for details.
If applicable, is the unit converted to top or rear vent per manual instructions, and the insulation discarded?
Venting YES NO
Are the venting components approved for the unit installed?
Does the venting configuration comply with venting diagrams?
Is venting installed and secured, and are clearances for the vent pipe and termination cap maintained?
If applicable, was a 1/4" rise maintained for every foot of horizontal run?
Was the termination installed and sealed?
Is the direct vent termination at the highest point in the vent assembly?
If applicable, are both chimney liners continuous from flue collars to termination?
Electrical and Wiring YES NO
Is the appliance connected to the household's 110/120v per local codes? Check local codes for receptacle placement.
Were the connections in the fireplace tested with a circuit tester?
Is the appliance properly grounded?
If applicable, is the supplied electrical/gang box affixed to the wall to facilitate the mounting of the receiver/battery box ?
Gas YES NO
Does the supply pressure meet the requirements shown on the rating plate?
Was a conversion performed?
Was a leak check performed and manifold pressures verified?
Is the shut-off valve installed and easily accessible to the customer?
This general checklist does not contain all pertinent installation details or specifics and does not supersede the guidelines in this manual. Your
Regency dealer/installer should use it in conjunction with manual instructions. Please follow all local codes and jurisdictions in authority.
Gas Installation Checklist

installation
10 | Grandview®G800C Gas Fireplace
05/18/21
2
REGENCY GAS INSTALLATION CHECKLIST
Finishing YES NO
If applicable, is only noncombustible material installed in the noncombustible areas?
Do clearances meet installation and manual requirements?
Do the mantels and/or projections comply with the installation manual?
If applicable, was the solid fuel fireplace warning plate installed?
Appliance Media Setup YES NO
Do commands from the remote or wall switch light the pilot and main burner?
Are the burner media/log set, glass door, and screen installed per instructions in the manual?
Was the air shutter on the proper setting after running the unit for 20 minutes?
If applicable, were the surround and trims installed according to the manual?
Was the operation of the fan, lights (if installed), and flame modulation checked?
Customer Tutorial and Presentation YES NO
Is the customer confident operating the new gas appliance and aware of all the features on the remote?
Confirm that the rating and lighting plates are attached to the appliance. Do not remove.
Was the customer informed of the location of the rating and lighting plates?
Was accessing unit controls in a power outage explained to the customer?
Are the model and serial numbers and the date of installation of the unit written in the manual and on the checklist?
Were the warranty and unit registration reviewed with the customer?
Comments:

Grandview®G800C Gas Fireplace | 11
owner's information
Before You Start
Safe installation and operation of this appliance
requires common sense, however, we are required
by the ANSI Standards to make you aware of the
following:
CHILDREN AND ADULTS SHOULD
BE ALERTED TO THE HAZARDS OF
HIGH SURFACE TEMPERATURES,
ESPECIALLY THE FIREPLACE GLASS,
AND SHOULD STAY AWAY TO AVOID
BURNS OR CLOTHING IGNITION.
INSTALLATION AND REPAIR
SHOULD BE DONE BY AN
AUTHORIZED SERVICE PERSON.
THE APPLIANCE SHOULD BE
INSPECTED BEFORE USE AND
AT LEAST ANNUALLY BY A
PROFESSIONALSERVICEPERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL, ETC. IT IS IMPERATIVE
THAT CONTROL COMPARTMENTS,
BURNERS AND CIRCULATING
AIR PASSAGEWAYS OF THE
APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES,
THE APPLIANCE SHOULD BE
LOCATED OUT OF TRAFFIC AND
AWAY FROM FURNITURE AND
DRAPERIES.
WARNING: FAILURE TO INSTALL
THIS APPLIANCE CORRECTLY
WILL VOID YOUR WARRANTY AND
MAY CAUSE A SERIOUS HOUSE
FIRE.
CLOTHING OR OTHER
FLAMMABLE MATERIAL SHOULD
NOT BE PLACED ON OR NEAR THE
APPLIANCE.
YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISED WHEN
THEY ARE IN THE SAME AREA
AS THE APPLIANCE. TODDLERS,
YOUNG CHILDREN AND OTHERS
MAY BE SUSCEPTIBLE TO AC-
CIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOM-
MENDED IF THERE ARE AT RISK
INDIVIDUAL IN THE HOUSE. TO
RESTRICT ACCESS TO A FIRE-
PLACE OR STOVE, INSTALL AN AD-
JUSTABLE SAFETY GATE TO KEEP
TODDLERS, YOUNG CHILDREN
AND OTHER AT RISK INDIVIDU-
ALS OUT OF THE ROOM AND AWAY
FROM HOT SURFACES.
ANY SAFETY SCREEN, GUARD,
OR BARRIER REMOVED FOR
SERVICING THE APPLIANCE,
MUST BE REPLACED PRIOR TO
OPERATING THE APPLIANCE.
IF THE BARRIER BECOMES
DAMAGED, THE BARRIER
SHALL BE REPLACED WITH THE
MANUFACTURER'S BARRIER FOR
THIS APPLIANCE.
A BARRIER DESIGNED TO REDUCE
THE RISK OF BURNS FROM THE
HOTVIEWINGGLASSISPROVIDED
WITH THIS APPLIANCE AND
SHALL BE INSTALLED FOR THE
PROTECTION OF CHILDREN AND
OTHER AT-RISK INDIVIDUALS

12 | Grandview®G800C Gas Fireplace
owner's information
13. Do not slam shut or strike the glass door.
14. Under no circumstances should any solid fuels
(wood, paper, cardboard, coal, etc.) be used in
this appliance.
15. The appliance area must be kept clear and free
of combustible materials, (gases and other
ammable vapours and liquids).
Important Message
Save These Instructions
The G800C Direct Vent Fireplace must be installed
in accordance with these instructions. Carefully read
all the instructions in this manual rst. Consult the
"authority having jurisdiction" to determine the need
for a permit prior to starting the installation. It is the
responsibility of the installer to ensure this replace
is installed in compliance with manufacturer's
instructions and all applicable codes.
General Safety Information
1. The appliance installation must conform with
local codes or, in the absence of local codes,
with the current National Gas Codes or ANSI
Z223.1 Installation Codes.
2. The appliance when installed, must be electrically
grounded in accordance with local codes, or
in the absence of local codes with the current
National Electrical Code, ANSI/NFPA 70.
3. See general construction and assembly
instructions. The appliance and vent should be
enclosed.
4. This appliance must be connected to the specied
vent and termination cap to the outside of the
building envelope. Never vent to another room
or inside a building. Make sure that the vent is
tted as per Venting instructions.
5. Inspect the venting system annually for blockage
and any signs of deterioration.
6. Venting terminals shall not be recessed into a
wall or siding.
7. Any safety glass removed for servicing must be
replaced prior to operating the appliance.
8. To prevent injury, do not allow anyone who is
unfamiliar with the operation to use the replace.
9. Wear gloves and safety glasses for protection
while doing required maintenance.
10. Be aware of electrical wiring locations in walls
and ceilings when cutting holes for termination.
11. Under no circumstances should this appliance
be modied. Parts that have to be removed for
servicing should be replaced prior to operating
this appliance.
12. Installation and any repairs to this appliance
should be done by a qualied service person.
A professional service person should be called
to inspect this appliance annually. Make it a
practice to have all of your gas appliances
checked annually.
CAUTION: Label all wires prior to discon-
nection when servicing controls. Wiring
errors can cause improper and danger-
ous operation. Verify proper operation
after servicing.
To Turn Appliance On/O
1. Ensure pilot is lit. This appliance will not operate
if the pilot is not lit. Follow the lighting instruc-
tions in manual to light pilot.
2. Locate the on/o switch located at the bottom
right hand corner of the appliance.
3. Flick the switch to turn on or o the appliance.
Optional Fan Operation
1 If the optional fan has been installed, the speed
of the fan can controlled by using the controller.
2. To control the speed of the fan, locate the fan
speed controller located either on the underside
of the rebox marked FAN with a dial and or
the wall.
If installed on the underside of the rebox, the
screen will need to be removed. See instructions
in this manual. If wall mounted simply use the dial
to control the speed of the fan.
Note:The fan may take 15-30 minutes to turn on
as this appliance has a fan thermo disc. If the fan
speed controller is turned to the ON position, the
fan will turn on automatically when heated and turn
OFF automatically when cooled down.
ON/OFF Switch
= ON = OFF

Grandview®G800C Gas Fireplace | 13
owner's information
Lighting the Pilot Using the Gas Control Knob Extender
1. Remove the knob extender from its cradle located on the rebox oor in front of the gas valve. See below.
Cradle Extender Knob
2. Slide the extender knob over the pilot/on/o knob located on the gas valve. See below.
3. Follow instructions on how to light the pilot in this manual or the lighting plate located on the underside of the unit.
4. Once the pilot is lit, remove the extender knob and put it back into the cradle for future use.
On/o/pilot knob on gas valve
Extender knob slid over on/o/pilot knob on gas valve

14 | Grandview®G800C Gas Fireplace
owner's information
920-019b 02.10.22
PROFLAME I REMOTE CONTROL OPERATING INSTRUCTIONS
WARNING:THETRANSMITTER AND RECEIVER ARE RADIO
FREQUENCY DEVICES. PLACING THE RECEIVER IN OR
NEAR METAL MAY SEVERELY REDUCETHE SIGNAL RANGE.
The Proflame 1 Transmitter provides for controlling the following hearth
appliance functions:
1. Main Burner On/Off
2. Main Burner flame modulation (6 levels)
3. Thermostat and Smart thermostat functions
4. Accent light modulation (6 levels)**
5. Comfort Fan speed modulation (6 levels)**
** This feature is not available on all models.
IMPORTANT:The Proflame Transmitter 1 is an integrated part of the
Proflame 1 System, which consists of these elements:
• Proflame 1 Transmitter, to be used in conjunction with:
• Integrated Fireplaces Control (Proflame 1 DFG)
The Proflame Transmitter uses a streamline design with a simple button
layout and informative LCD display (Fig. 1). A Mode Key is provided to
index between the features and a Thermostat Key is used to turn on/off
or index through Thermostat functions (Fig. 1 & 2). Additionally, a Key
Lock feature is provided (Fig. 22).
Figure 1: Proflame Transmitter
Figure 2: Transmitter LCD Display
TECHNICAL DATA
REMOTE CONTROL
Supply Voltage 4.5V (three 1.5V AAA batteries)
Ambient temperature
ratings
0 - 50oC (32 - 122oF)
Radio Frequency 315 MHZ
ATTENTION!
- Turn “OFF” the main gas supply of the appliance during installation or
maintenance of the Receiver device.
- Turn “OFF” main gas supply to the appliance prior to removing or rein-
serting the batteries.
- In case of remote control malfunction, turn off the IFC device using the
"ON/OFF" main switch.
- For installation / maintenance, switch off the IFC device removing main
power supply plug.
OPERATING PROCEDURE
Pairing the remote control to remote receiver/battery
holder (if required)
Install the 4 AA batteries into the receiver battery bay. Note the polarity
of the battery and insert into the battery bay as indicated on the battery
cover (+/-). Place the 3 position slider switch in the “Remote” position..
Press the PRG button located on the top right hand corner of receiver,
see the receiver instruction(*). The Receiver will “beep” three (3) times to
indicate that it is ready to synchronize with a Transmitter. Install the 3 AAA
type batteries in the Transmitter battery bay, located on the base of the
Transmitter. (fig. 3) With the batteries already installed in the Transmitter,
push the On button. The Receiver will “beep” four times to indicate the
Transmitter’s command is accepted and sets to the particular code of
that Transmitter. The system is now initialized.
(*) The receiver may be independent or integral to the IFC hearth appliance
control module. The receiver instruction may not be independent when
part of the IFC.
Figure 3: Battery Compartment
Note: May not be exactly as shown as hand-held may be silver or black.
1
Proame I Remote Control Operating Instructions
**

Grandview® G800C Gas Fireplace | 15
owner's information
919-829 12.17.18
Figure 4: Remote Control dis-
play in Farenheit.
Temperature indication Display
With the system in the "OFF" position, press the Thermostat Key and
the Mode Key at the same time. Look at the LCD screen on the transmit-
ter to verify that a C or F is visible to the right of the room temperature
display (Figures 4 & 5).
Figure 5: Remote Control dis-
play in Celsius.
Turn on the Appliance
With the system OFF, press the ON/
OFF Key on the Transmitter. The
Transmitter display will show some
other active Icons on the screen. At
the same time the Receiver will ac-
tivate the appliance. A single “beep”
from the Receiver will confirm recep-
tion of the command.
Figure 6: Remote Control
display
Remote‑Flame Control
The Proflame has six (6) flame levels. With the system on, and the flame
level at the maximum in the appliance, pressing the Down Arrow Key
once will reduce the flame height by one step until the flame is turned off.
The Up Arrow Key will increase the flame height each time it is pressed.
If the Up Arrow Key is pressed while the system is on but the flame is off,
the flame will come on in the high position. ( Fig. 7 & 8 ) A single “beep”
will confirm reception of the command.
Fig. 7
Fig. 8
Room Thermostat (Transmitter Operation)
The Remote Control can operate as a room thermostat. The thermostat
can be set to a desired temperature to control the comfort level in a room.
To activate this function, press the Thermostat Key (Fig. 1). The Lcd
display on the Transmitter will change to show that the room thermostat
is “ON” and the set temperature is now displayed (Fig. 9). To adjust the
set temperature, press the Up or Down Arrow Keys until the desired set
temperature is displayed on the LCD screen of the Transmitter.
Figure 9 Figure 10
Turn off the Appliance
With the system ON, press the ON/OFF Key on the Transmitter. The
Transmitter LCD display will only show the room temperature (Fig. 6).
At the same time the Receiver will turn off the appliance. A single “beep”
from the Receiver confirms reception of the command.
2
919-829 12.17.18
Figure 4: Remote Control dis-
play in Farenheit.
Temperature indication Display
With the system in the "OFF" position, press the Thermostat Key and
the Mode Key at the same time. Look at the LCD screen on the transmit-
ter to verify that a C or F is visible to the right of the room temperature
display (Figures 4 & 5).
Figure 5: Remote Control dis-
play in Celsius.
Turn on the Appliance
With the system OFF, press the ON/
OFF Key on the Transmitter. The
Transmitter display will show some
other active Icons on the screen. At
the same time the Receiver will ac-
tivate the appliance. A single “beep”
from the Receiver will confirm recep-
tion of the command.
Figure 6: Remote Control
display
Remote‑Flame Control
The Proflame has six (6) flame levels. With the system on, and the flame
level at the maximum in the appliance, pressing the Down Arrow Key
once will reduce the flame height by one step until the flame is turned off.
The Up Arrow Key will increase the flame height each time it is pressed.
If the Up Arrow Key is pressed while the system is on but the flame is off,
the flame will come on in the high position. ( Fig. 7 & 8 ) A single “beep”
will confirm reception of the command.
Fig. 7
Fig. 8
Room Thermostat (Transmitter Operation)
The Remote Control can operate as a room thermostat. The thermostat
can be set to a desired temperature to control the comfort level in a room.
To activate this function, press the Thermostat Key (Fig. 1). The Lcd
display on the Transmitter will change to show that the room thermostat
is “ON” and the set temperature is now displayed (Fig. 9). To adjust the
set temperature, press the Up or Down Arrow Keys until the desired set
temperature is displayed on the LCD screen of the Transmitter.
Figure 9 Figure 10
Turn off the Appliance
With the system ON, press the ON/OFF Key on the Transmitter. The
Transmitter LCD display will only show the room temperature (Fig. 6).
At the same time the Receiver will turn off the appliance. A single “beep”
from the Receiver confirms reception of the command.
2
920-019 12.17.18
Smart Thermostat (Transmitter Operation)
The Smart Thermostat function adjusts the flame height in accordance
to the difference between the set point temperature and the actual room
temperatures. As the room temperature gets closer to the set point the
Smart Function will modulate the flame down.
To activate this function, press the Thermostat Key (Fig. 1) until the word
"SMART" appears to the right of the temperature bulb graphic (Fig. 11).
To adjust the set temperature, press the Up or Down Arrow Keys until
the desired set temperature is displayed on the LCD screen of the
Transmitter (Fig. 12).
Note. When Smart Thermostat is activated, manual flame height adjust-
ment is disabled.
Figure 12Figure 11: Smart Flame Function
Fan Speed Control**
If the appliance is equipped with a hot air circulating fan, the speed of
the fan can be controlled by the Proflame system. The fan speed can be
adjusted through six (6) speeds. To activate this function use the Mode Key
(fig.1) to index to the fan control icon (Fig. 13). Use the Up/Down Arrow
Keys (fig.1) to turn on, off or adjust the fan speed (fig. 14). A single “beep”
will confirm reception of the command.
Figure 13 Figure 14
Remote dimmer control (Light)**
The auxiliary function controls the AUX power outlet by the dimmable
light control. To activate this function use the Mode Key (fig. 1) to index
to the AUX icon (fig. 15 & 16).
The intensity of the output can be adjusted through six (6) levels. Use
the Up/Down Arrow Keys (fig.1) adjust the output level (fig. 16). A single
“beep” will confirm reception of the command.
Note: This function is available only with the IFC Control Module.
Figure 15 Figure 16
KEY LOCK
This function will lock the keys to avoid unsupervised operation.
To activate this function, press the MODE and UP Keys at the same
time (fig. 21).
To de-activate this function, press the MODE and UP Keys at the same
time.
Figure 18
3
18

16 | Grandview®G800C Gas Fireplace
owner's information
920-019 01.16.19
LOW BATTERY POWER DETECTION
Transmitter
The life span of the remote control batteries depends on various factors:
quality of the batteries used, the number of ignitions of the appliance,
the number of changes to the room thermostat set point, etc.
When the Transmitter batteries are low, a Battery Icon will appear on the
LCD display of the Transmitter (Fig. 22) before all battery power is lost.
When the batteries are replaced this Icon will disappear.
Figure 19
CPI/IPI Switch
This appliance comes equipped with a CPI/IPI switch.
The functions of both the CPI/IPI switch are as follows:
Continuous pilot (CPI) - A pilot that, once placed in operation, is intended to remain ignited
continuously until it is manually interrupted.
Intermittent pilot (IPI) - A pilot that is automatically ignited when an appliance is called on to
operate and which remains continuously ignited during each period of main burner operation. The
pilot is automatically extinguished when each main burner operating cycle is completed
The mode of the fireplace is easily changed from an intermittent pilot ignition system (IPI) to a
continuous pilot ignition system (CPI) by using the silver toggle switch located on the fireplace.
(See noted location of CPI/IPI Switch)
The benefits of having CPI are as follows:
-Keeps venting primed for trouble free start-up under colder weather conditions or inversions.
-Keeps the unit glass warm, which decreases the amount of condensation on start-up.
-Provides owners with flexibility to choose a traditional continuous pilot. (7 day/Pilot on Demand)
The primary benefit of having the IPI function is a significant savings on fuel as the pilot will only
run when there is a call for heat.
ENABLE / DISABLE functions on the Proflame I remote only.
1. Remove one battery from the remote.
2. Press and hold both the ON/OFF and the MODE button at the same time
3. Reinstall the battery (removed in Step 1) while still holding both buttons (keep holding both
buttons and once all batteries are installed then release the MODE button only).
4. The screen will show CFG.
5. Use the up or down arrow button to program out the function on the remote.
Note: You should never program out the fan (If installed) feature on the remote.
It is not possible to remove the thermostat mode on this remote control.
4
ENABLE / DISABLE functions on the Proame I remote only.
1. Remove one battery from the remote.
2. Press and hold both the ON/OFF and the MODE button at the same time.
3. Reinstall the battery (removed in Step 1) while still holding both buttons (keep holding both buttons and
once all batteries are installed then release the MODE button only).
4. The screen will show CFG.
5. Use the up or down arrow button to program out the function on the remote.
19

Grandview® G800C Gas Fireplace | 17
owner's information
1 | 1
Remote Receiver/Battery Holder Battery Replacement & Battery Back up if 120 volt
power is lost witihin home
How to replace/add the batteries on remote receiver (Proflame 1).
Note : If a wall switch cover plate is installed, first remove cover plate by removing 2 small phillips head screws
STEP 1
STEP 2
STEP 3
STEP 4 Reinstall wall cover plate with 2 Phillips head screws.
Replace 4 x AA batteries and insert the battery
compartment back into remote receiver/battery holder
Move both the left/right slides
as shown below.
The battery compartment
will be pushed out slightly,
to allow to easily extract it
Extract the battery
compartment from the remote
receiver/battery holder
Close the right slide
Keeping the battery compartment
pressed in, close the left slide
Proame I Remote Receiver Battery Replacement
Remote Receiver Battery Replacement
How to replace/add the batteries on remote receiver.
Note:4 AA batteries are mandatory in the remote receiver to operate appliance when using remote control.
The remote receiver will be located on the bottom right hand side of appliance next to the fan speed controller. The safety screen will need to be removed
to gain access to this remote receiver.

18 | Grandview®G800C Gas Fireplace
operating instructions
Backup Function
If the batteries of the receiver are low, the appliance
can be switched on manually by moving the three-
position slider switch on the receiver to the ON
position.
Operating Procedure for Remote Control
Functionality of the Receiver
The receiver is supplied by four AA batteries (see
Fig. 3). The receiver accepts commands via radio
signals sent from the transmitter. The receiver sends
commands by the wire harness to the multifunctional
gas control. When the system is turned on, an
acoustic signal (beep) is generated to indicate that
the receiver is ready to receive commands from
the remote control.
Turn on the Appliance
When the ON/OFF key is pressed, the LED on the
transmitter illuminates and the remote control is
switched on. At the same time, the receiver connects
the thermopile to the gas valve millivolt coil and the
appliance main burner turns on in the high position.
A single acoustic signal from the receiver conrms
the reception of the command.
Low Battery Detection (Receiver)
The duration of the remote control batteries depends
on many factors: the quality of the batteries used,
the number of ignitions of the appliance, etc. If
the receiver batteries are low, a triple acoustic
signal is emitted by the receiver when it receives
a command from the transmitter. This is an alert
of a low battery condition before battery power is
lost altogether. As soon as the depleted batteries
are replaced, the acoustic signal from the receiver
conrms the reception of the ON/OFF command
from the transmitter.
ON
REMOTE
OFF
Warnings and Cautions
Turn O the Appliance
If the appliance and the remote control are
switched on and the ON/OFF key is pressed, the
remote control is turned o. At the same time, the
receiver removes power from the gas valve millivolt
coil and the appliance main burner turns o. A
double acoustic signal from the receiver conrms
the reception of the command.
CAUTIONS
• Property damage hazard.
Excessive heat can cause property
damage.
• The replace can stay ignited for
many hours. Take care to turn o
the replace if it is unattended by
adults. Do not leave the remote
control where children can reach
it.
WARNINGS
• Fire hazard. Can cause severe
injury or death.
• The receiver causes the ignition
of the replace. The replace
can turn on suddenly. Keep away
from the burner, especially when
operating the BACKUP switch.

Grandview®G800C Gas Fireplace | 19
owner's information
Safety Screen Removal
1. Slide screen up.
2. Slide screen
right.
3. Lower screen
down.
4. Swing screen
outwards while
keeping the screen
level and remove.
1. To install the safety screen—Reverse steps above.
Safety Screen Installation
Glass Door Removal
1. To install the door—Reverse steps above.
1. To remove the glass door - place both hands on either side of the
latch. Pull forward then up to unlock, repeat on opposite side.
Important: After releasing the latches, support the weight of the
door.
2. With both latches released, support the door with both hands
and tilt out to approximately a 60 degree angle.
3. Lift the door up and out of lower slots to remove.
Glass Door Installation
Latch locations

installer's information
20 | Grandview®G800C Gas Fireplace
This includes:
1. Clocking the appliance to ensure the correct
ring rate (rate noted on label 27,000 Btu/h
for natural gas and propane), after burning
appliance for 15 minutes.
2. If required, adjusting the primary air to ensure
that the ame does not carbon. First allow the
unit to burn for 15-20 min. to stabilize.
CAUTION: Any alteration to the product that causes
sooting or carboning that results in damage is
not the responsibility of the manufacturer.
Locating Your Gas Fireplace
1. When selecting a location for your replace,
ensure that the clearances are met.
A) Flat on Wall
B) Flat on Wall Corner
C) Recessed into Wall/Alcove
D) Corner
Diagram 1
2. The appliance must be installed on a at, solid,
continuous surface For example a wood, metal
or concrete oor or in a raised (on the wall)
application. The appliance must be installed on
a metal or wood panel extending the full width
and depth of the appliance.
3. The G800C Gas Fireplace can be installed in a
recessed position or framed out into the room
as in A, B, C and D. See Diagram 1.
Installation Checklist
1. Locate appliance
a) Room location (Refer to "Locating Your
Gas replace" section)
b) Clearances to Combustibles (Refer to
"Clearances" section)
c) Mantle Clearances (Refer to "Combustible
Mantel Clearances" section)
d) Framing & Finishing Requirements (Refer
to "Framing & Finishing" section)
e) Venting Requirements (Refer to "Venting"
section)
2. Assemble Top Standos and Top Facing Support
and Side Nailing Strips (Refer to "Unit Assembly
Prior to Installation" Section). NOTE: Must be
done before installing unit into place.
IMPORTANT: If installing the fan kit or chang-
ing this from rear vent to top vent, this
must be completed prior to installing the
appliance into the framed opening.
3. Install vent (Refer to "Venting" sections).
4. Make gas connections. Test the pilot. Must be
as per Diagram (Refer to "Pilot Adjustment "
section).
Convert to propane if desired (Refer to "Gas
Line Installation" and "Conversion Kit from NG
to LPG" sections).
5. Make electrical connections to receptacle sup-
plied with unit (recommended).
6. Install standard and optional features. Refer
to the following sections:
a. Standard Glass Door
b. Rear to top vent conversion
c. Coolwall conversion
d. Fan Installation (Optional)
e. Nailing ange installation
f. Electrical access/120 volt power installation
by others
g. Wall Mount On/OFf Switch + Receiver Instal-
lation
h. Coolwall Clearances/Framing/Finishing
i. Clean Front Clearance/ Framing/Finishing
j. Outside Finish Clearance/ Framing/
Finishing
k. LP Conversion (optional)
l. Inner Panels or Brick Panels (Must install one
of the options)
m. Media (Glass crystals)
n. Log Set Installation
o. HeatWave Kit
7. Final check.
4. This appliance is Listed for bedroom installations
using the standard Remote (millivolt thermostat
system). Some areas may have further require-
ments, check local codes before installation.
5. The G800C Gas Fireplace are approved for alcove
installations, see "Clearances" section for details.
6. We recommend that you plan your installa-
tion on paper using exact measurements for
clearances and oor protection before actually
installing this appliance. Have an authorized
inspector, dealer, or installer review your plans
before installation.
HeatWave Duct System Op-
tional Kit #946-556
The HeatWave Air Duct Kit increases the
eectiveness of your replace by dispersing warm
air from the replace to remote locations in the
same room or other rooms in your home.
Up to two kits may be installed on the replace.
Please Note: Only 1 HeatWave kit may be oper-
ated at one time. This includes the internal blower
option as well.
The HeatWave Duct Kit has dierent
clearance and framing requirements, check
the HeatWave manual for details.