Reliable F156 Series Manual

The Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523
Models F1 Series
Standard Response
Standard Spray
Bulletin 013 Rev. I
Bulletin 013 Rev. I
Model F156 Sprinkler Types
Standard Upright
Standard Pendent
Conventional
Vertical Sidewall
Horizontal Sidewall
Model F156 Recessed Sprinkler Types
Pendent/F1/F2/FP
Horizontal Sidewall
Model F142, F1XLH & F128 Sprinkler Types
Standard Upright
Standard Pendent
Model F142, F1XLH & F128 Recessed Sprinkler
Types
Pendent/F1/F2/FP
Approval Organizations
1. Underwriters Laboratories Inc. and certified for
Canada (cULus)
2. Factory Mutual Approvals (FM)
3. Loss Prevention Council (LPCB, UK)
4. VdS Schadenverhütung GmbH
UL Listing Category
Sprinklers, Automatic & Open (VNIV)
Recessed
Pendent/F1/F2
Horizontal Sidewall
Pendent ConventionalUpright
Vertical Sidewall
Recessed
Horizontal Sidewall
Recessed
Pendent/FP
XLH Upright
XLH Pendent XLH Recessed
Pendent F1/F2
XLH Recessed
Pendent FP
Product Description
The F156, F142, F1XLH & F128 Series Glass Bulb
Sprinkler combines the durability of a standard sprinkler
with the attractive low profile of a decorative sprinkler.
Whether installed on exposed piping or in an office ceil-
ing, it is functional and attractive.
Beautifully versatile is the description for the Reliable
Models F156, F142, F1XLH & F128 Series Recessed
glass bulb sprinkler. Recessing the F156, F142, F1XLH &
F128 Series enhances its already low profile decorative
appearance, and facilitates a rapid and perfect installa-
tion.
The recessed escutcheon of the Models F156, F142,
F1XLH & F128 are highly adjustable. The two piece con-
struction makes field installation a very easy and rapid
task. This also allows ceiling panels to later be removed
without shutting down the fire protection system, thus fa-
cilitating maintenance of above ceiling services.
The F156, F142, F1XLH & F128 Series Automatic Sprin-
kler utilizes a 5.0 mm frangible glass bulb. The glass bulb
consists of an accurately controlled amount of special
fluid hermetically sealed inside a precisely manufactured
glass capsule. This glass bulb is specially constructed to
provide fast thermal response.
At normal temperatures, the glass bulb contains the
fluid in both the liquid phase and in the vapor phase. The
vapor phase can be seen as a small bubble. As heat is
applied, the liquid expands forcing the bubble smaller
and smaller as the liquid pressure increases. Continued
heating forces the liquid to push out against the bulb,
causing the glass to shatter, opening the waterway and
allowing the deflector to distribute the discharging water.
The F156, F142, F1XLH & F128 Series Sprinkler tem-
perature rating is identified by the color of the glass bulb
capsule as well as frame color where applicable.

Technical data:
Models Discharge Coefficient Response Thread
Size
Max.
Working
Pressure
Min.
Working
Pressure
Temperature
Rating Finish
F156 K 5.6
Standard
1/2” NPT
(R1/2) 175 PSI 7 PSI
See
“Temperature
Ratings” Table
See
“Finish Table”
F142
F1XLH K 4.2
F128 K 2.8
Material Data:
Frame Deflector Load Screw Pintle Cup Washer Bulb
DZR Brass
QM Brass
CDA Alloy 260,
CDA Alloy 220
or
CDA Alloy 510
CDA Alloy 360
or
CDA Alloy 544
CDA Alloy 360
or
CDA Alloy 544
CDA Alloy 651
or
CDA Alloy 693
Nickel Alloy 440 or Alloy 360
coated with PTFE Adhesive
Tape
Glass
2.
Model F142, F1XLH Upright

3.
Model F156, Upright, Pendent & Conventional Sprinklers
Model F142, F1XLH & F128 Upright & Pendent Sprinklers
Installation Wrench: Model D Sprinkler Wrench
Installation Data:
Nominal
Orifice
Thread
Size
Nominal K Factor Sprinkler
Height
Approval
Organization
Sprinkler Identification Number
(SIN)
US Metric Upright Pendent
Standard-Upright (SSU) and pendent Deflectors Marked to Indicate Position
1/2” (15mm) (1) 1/2” NPT (R1/2) 5.6 80 2.25” (57mm) 1,2,3,4 RA1325(2)(3)(5) RA1314(2)(3)(5)
7/16” (10mm) 1/2” NPT (R1/2) 4.2 60 2.25” (57mm) 1 RA1323(2) RA1313
3/8 (10mm) 1/2” NPT (R1/2) 2.8 40 2.25” (57mm) 1,2 RA1321(2)(3)(4) RA1311
Conventional-Install in Upright or Pendent Position
15mm (1) 1/2” NPT (R1/2) 5.6 80 57mm 3, 4 RA1375(5)
(1) Refer to Bulletin 024 for Special Response Sprinklers (F1S5-56)
(2) cULus Listed corrosion resistant (Polyester coated) sprinkler.
(3) Polyester coated FM Approved sprinkler.
(4) FM Approved for SSU up to and including 200°F (93°C).
(5) Polyester coated LPCB & VdS approved sprinkler RA1325, RA1314 & RA1375.
Pendent Conventional
Upright
Model F156, F142, F1XLH & F128 F1 or F2 Model F156, F142, F1XLH & F128 FP
Model F156, F142, F1XLH & F128 Recessed Pendent Sprinklers(1)
Installation Wrench: Model GFR2 Sprinkler Wrench
Installation Data:
Nominal
Orifice
Thread
Size
K Factor Sprinkler
Height
Sprinkler Identification Number
(SIN)
US Metric
1/2” (15mm) 1/2” NPT (R1/2) 5.6 80 2.25” (57mm) RA1314
7/16” (10mm) 1/2” NPT (R1/2) 4.2 60 2.25” (57mm) RA1313
3/8” (10mm) 1/2” NPT (R1/2) 2.8 40 2.25” (57mm) RA1311
(1) Refer to escutcheon data table for approvals & dimensions

4.
Model F156 Vertical Sidewall Sprinkler
Installation Wrench: Model D Sprinkler Wrench
Installation Position: Upright or Pendent
Approval Type: Light Hazard Occupancy
U.S. Patent No. 6,374,920
Sprinkler Type Deflector to Ceiling Distance
(Min. - Max.)
Upright 4” (102mm) - 12” (305mm)
Pendent 4” (102mm) - 12” (305mm)
Installation Data:
Nominal
Orifice Thread Size
Nominal K Factor Sprinkler
Height
Approval (1)
Organizations
Sprinkler
Identification
Numbers (SIN)
US Metric
½” (15mm) ½” NPT (R1/2) 5.6 8.0 2.25” (57mm) 1,2,3 RA1385(1)(2)(3)
(1) LPC Approval is pendent only, 57°C through 141°C ratings.
(2) cULus Listed corrosion resistant (Polyester coated) sprinkler.
(3) cULus Listed & FM Approved corrosion resistant for lead, wax and wax over lead.
Model F156 Horizontal Sidewall Sprinkler
Deflector: HSW
Installation Wrench: Model D Sprinkler Wrench
Installation Data:Horizontal Sidewall
Nominal Orifice Thread Size
Nominal K Factor Sprinkler
Height Approval Organizations Sprinkler
Identification
Numbers (SIN)
US Metric Light Hazard Ordinary
Hazard
½” (15mm) ½” NPT (R1/2) 5.6 80 2.63” (67mm) 1,2 1 RA1335(1)(2)(3)
(1) cULus Listed corrosion resistant (Polyester coated) sprinkler.
(2) cULus Listed & FM Approved corrosion resistant for lead, wax and wax over lead.
(3) Polyester coated FM approved sprinkler.
Horizontal Sidewall
Vertical Sidewall
Note: For Recessed HSW Sprinklers use installation wrench GFR2.

Application
Model F156, F142, F1XLH, F128 & Model F156, F142, F1XLH &
F128 Recessed sprinklers are used in fixed fire protection systems:
Wet, Dry, Deluge or Preaction. Care must exercised that the orifice
size, temperature rating, deflector style and sprinkler type are in ac-
cordance with the latest published standards of the National Fire
Protection Association or the approving Authority Having Jurisdic-
tion Installation.
Installation
Model F156, F142, F1XLH & F128 Series sprinklers are standard
response sprinklers intended for installation as specified in NFPA
13. They must also be installed with the Model D Sprinkler Wrench
specifically designed by Reliable for use with these sprinklers.
The Model F156, F142, F1XLH & F128 Recessed Sprinklers
are to be installed with a maximum recess of ¾ inch (19mm). The
Model F1, F2, and FP Escutcheon illustrated are the only recessed
escutcheon to be used with the Model F156, F142, F1XLH & F128
Recessed Sprinklers. The use of any other recessed escutcheon
will void all approvals and negate all warranties. When installing
Model F156, F142, F1XLH & F128 Recessed Sprinklers use the
Model GFR2 Sprinkler Wrench. Any other type of wrench may
damage these sprinklers.
Note: A leak tight ½” NPT (R1/2) sprinkler joint can be obtained with
a torque of 8-18 ft-lbs (10,8 - 24,4 N-m). Do not tighten sprinklers
over maximum recommended torque. It may cause leakage or
impairment of the sprinklers.
Glass bulb sprinklers have orange covers to protect the bulb dur-
ing the installation process. REMOVE THIS PROTECTION ONLY
AFTER THE SYSTEM HAS BEEN HYDROSTATICALLY TESTED
AND, WHEN APPLICABLE, THE ESCUTCHEONS HAVE BEEN
INSTALLED. RASCO wrenches are designed to install sprinklers
when covers are in place.
Ordering Information
Specify:
1. Sprinkler Model
2. Sprinkler Type
3. Orifice Size
4. Deflector Type
5. Temperature Rating:
- Specify when ordering
- Model F156 Pendent Sprinkler
6. Sprinkler Finish
7. Escutcheon Finish (where applicable)
Note: When Models F156, F142, F1XLH & F128 Recessed Sprinklers
are ordered, the sprinklers and escutcheons are packaged separately.
Escutcheon Data (1)
(1) SIN: RA1335 - cULus and FM permits use with F1 or F2 escutcheons for light
hazard only.
Maintenance
The Model F156, F142, F1XLH & Model F156, F142, F1XLH
& F128 Recessed Sprinklers should be inspected quarterly and
the sprinkler system maintained in accordance with NFPA 25.
Do not clean sprinklers with soap and water, ammonia or any
other cleaning fluid. Remove any sprinkler which has been
painted (other than factory applied) or damaged in any way. A
stock of spare sprinklers should be maintained to allow quick
replacement of damaged or operated sprinklers. Prior to instal-
lation, sprinklers should be maintained in the original cartons
and packaging until used to minimize the potential for damage
to sprinklers that would cause improper operation or non-oper-
ation.
Temperature Ratings
Classification
Sprinkler
Temperature Max. Ambient
Temp.
Bulb
Color
°C °F
Ordinary
Ordinary
Intermediate
Intermediate
High(1)
Extra High(1)
57
68
79
93
141
182
135
155
175
200
286
360
100°F (38°C)
100°F (38°C)
150°F (66°C)
150°F (66°C)
225°F (107°C)
300°F (149°C)
Orange
Red
Yellow
Green
Blue
Mauve
(1) Not available for recessed Sprinklers.
Maximum Working Pressure
175 psi (12 bar)
100% Factory tested hydrostatically to 500 psi (34.5 bar)
Finish(1)
Standard Finishes
Sprinkler Escutcheon
Bronze
Chrome
Polyester Coated (6)(7)(9)
Brass
Chrome
White Painted
Special Application Finishes
Sprinkler Escutcheon
Bright Brass (2)
Black Plated
Black Paint (3)(9)
Off White (3)(9)
Satin Chrome
Lead Plated (3)(4)(8)
Wax Coated (3)(4)(5)(8)
Wax Over Lead (3)(4)(5)(8)
Bright Brass
Black Plated
Black Paint
Off White
Satin Chrome
(1) Other colors and finishes are available on special order. Consult factory for
details. Custom color painted sprinklers may not retain their UL Corrosion
resistance listing.
(2) 200°F (93°C) maximum.
(3) UL and ULC listed only.
(4) 155°F to 200°F (68°C to 93°C) ratings only.
(5) 286°F (141°C) sprinklers may be coated for ambient conditions not exceeding
150°F (66°C).
(6) cULus listed “corrosion resistant” applies to SIN Number RA1325 (Upright)
RA1323 (upright), RA1321(Upright), RA1335 (HSW), RA1385(VSW) and
RA1314 (Pendent) in standard black or white. Corrosion resistance in other
polyester colors is available upon request.
(7) FM Approved finish as “Polyester Coated” applies only to SIN number
RA1314 & RA1321 (Pendent) in standard black or white.
(8) FM Approved finish applies only to SIN number RA1335 & RA1385.
(9) LPCB and VdS Approved finish applies only to RA1325, RA1314 and RA1375.
5.

• Automatic sprinklers
• Flush automatic sprinklers
• Recessed automatic sprinklers
• Concealed automatic sprinklers
• Adjustable automatic sprinklers
• Dry automatic sprinklers
• Intermediate level sprinklers
• Open sprinklers
• Spray nozzles
• Alarm valves
• Retarding chambers
• Dry pipe valves
• Accelerators for dry pipe valves
• Mechanical sprinkler alarms
• Electrical sprinkler alarm switches
• Water flow detectors
• Deluge valves
• Detector check valves
• Check valves
• Electrical system
• Sprinkler emergency cabinets
• Sprinkler wrenches
• Sprinkler escutcheons and guards
• Inspectors test connections
• Sight drains
• Ball drips and drum drips
• Control valve seals
• Air maintenance devices
• Air compressors
• Pressure gauges
• Identification signs
• Fire department connection
Reliable offers a wide selection of sprinkler components. Following are some of the many
precision-made Reliable products that guard life and property from fire around the clock.
Reliable...For Complete Protection
The Reliable Automatic Sprinkler Co., Inc.
[phone] Sales Offices
[phone] Sales Fax
[phone] Corporate Offices
www.reliablesprinkler.com Internet Address
Manufactured by
Recycled
Paper
Revision lines indicate updated or new data.
EG. Printed in U.S.A. 07/12 P/N 9999970299
The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory
Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable.
Products manufactured and distributed by Reliable have been protecting life and property for over 90 years, and are installed and serviced by the most highly
qualified and reputable sprinkler contractors located throughout the United States, Canada and foreign countries.