ResMed ClimateLineAir Oxy User manual

User guide
English
User guide

English 1
ENGLISH
About your ClimateLineAir
The ClimateLineAir™is heated air tubing that delivers the
desired temperature at your mask. ClimateLineAir Oxy is a
variant of the ClimateLineAir that has a built-in oxygen
connector to attach a supplemental oxygen supply.
When used with the HumidAir™humidifier, ClimateLineAir
heated air tubing allows you to use Climate Control. Climate
Control is designed to make therapy more comfortable by
enabling constant temperature and maintaining humidity.
The ClimateLineAir heated air tubing is designed for use with
AirSense™10 / AirCurve™10 and Lumis™devices. Please read
this entire user guide together with your device user guide
before using your ClimateLineAir heated air tubing.
Note:
•Not all types of air tubing are available in all regions.
•Lumis does not include S9 Lumis Tx.
Setup

2
1. Make sure the device is connected and turned on.
2. Hold the cuff of the air tubing and line up the air tubing
connector with the connector port.
3. Push the cuff until the connector clicks into place.
ClimateLineAir connected will briefly display on the
device screen.
4. Connect the assembled mask to the free end of the air
tubing.
Setup with supplemental oxygen
To set up the ClimateLineAir Oxy with supplemental oxygen,
perform the steps outlined in the setup section and the
following additional steps.
1. Remove the cap from the oxygen connector.
2. Connect the oxygen supply tubing to the oxygen
connector.
Make sure it is firmly attached.

English 3
Notes:
•Before adding oxygen, familiarize yourself with the specific
warnings relating to the use of supplemental oxygen.
These can be found at the end of your device User Guide.
•If you use the ClimateLineAir Oxy without supplemental
oxygen, make sure the cap of the oxygen connector is
firmly attached.
Climate Control
Climate Control is an intelligent system that controls the
humidifier and the ClimateLineAir heated air tubing to deliver
constant, comfortable temperature and humidity levels during
therapy.
Designed to prevent dryness of the nose and mouth, it
maintains the set temperature and relative humidity while you
sleep. Climate Control can be set to either Auto or Manual
and is only available when both the ClimateLineAir and the
HumidAir humidifier are attached.
Climate Control Auto
Climate Control Auto is the recommended and default setting.
Climate Control Auto is designed to make therapy as easy as
possible, so there is no need to change the temperature or
humidity settings.
The Tube Temperature is set to Auto (80°F [27°C]) and
Climate Control adjusts the humidifier output to maintain a
constant, comfortable humidity level of 85% relative humidity
while protecting against rainout (water droplets in the air
tubing and mask).
Tube Temperature
In Climate Control Auto there is no need to change any
settings, but if the air in the mask feels too warm or cold you
can adjust the tube temperature to find what is most
comfortable for you. You can set the Tube Temperature to
anywhere between 60–86°F (16–30°C), or turn it off
completely.

4
To adjust the Tube Temperature:
1. In My Options, turn the dial to highlight Tube Temp.and
then press the dial.
2. Turn the dial to adjust the temperature and press the dial
to save the change.
Climate Control Manual
Designed to offer you more flexibility and control over your
settings, Climate Control Manual lets you adjust the
temperature and humidity to the setting which is most
comfortable for you.
In Climate Control Manual, the tube temperature and the
humidity level can be set independently however, rainout
protection is not guaranteed. If rainout does occur, first try
increasing the tube temperature. If the air temperature
becomes too warm and rainout continues, try decreasing the
humidity.
To change to Climate Control Manual:
1. In My Options, turn the dial to highlight Climate Ctrl and
then press the dial.
2. Turn the dial to select Manual and press the dial to save
the change.
Humidity Level
The humidifier moistens the air and is designed to make
therapy more comfortable. If you are getting a dry nose or
mouth, turn up the humidity. If you are getting any moisture
in your mask, turn down the humidity.
You can set the Humidity Level to Off or between 1 and 8,
where 1 is the lowest humidity setting and 8 is the highest
humidity setting.

English 5
To adjust the Humidity Level:
1. In My Options, turn the dial to highlight Humidity Level
and then press the dial.
2. Turn the dial to adjust the humidity level and press the dial
to save the change.
If you have been using Climate Control Manual and want to
return to Climate Control Auto, follow the instructions below.
To change to Climate Control Auto:
1. In My Options, turn the dial to highlight Climate Ctrl and
then press the dial.
2. Turn the dial to select Auto and then press the dial to save
the change.
Caring for your ClimateLineAir
It is important that you regularly clean your air tubing to make
sure you receive optimal therapy. The following sections will
help you with disconnecting, cleaning, checking and
reconnecting your air tubing.

6
Disconnecting
1. Hold the cuff of the air tubing, apply gentle pressure to the
release buttons and pull it away from the device.
2. Hold both the cuff of the air tubing and the swivel of the
mask, then gently pull apart.
Note: Only hold and pull the cuff of the air tubing. Do not hold
or pull the tubing itself as it may cause damage.
Cleaning
You should clean the air tubing weekly as described.
1. Wash the air tubing in warm water using mild detergent.
Do not wash in a dishwasher or washing machine.
2. Rinse the air tubing thoroughly and allow to dry, out of
direct sunlight and/or heat.
Checking
You should regularly check the air tubing for any damage. If
there are any holes, tears or cracks you should replace it.
Reconnecting the air tubing
When the air tubing is dry, you can reconnect it to the device.
1. Connect the air tubing firmly to the air outlet located on
the rear of the device.
2. Connect the free end of the air tubing firmly onto the
assembled mask.

English 7
Troubleshooting
If you have any problems, refer to the troubleshooting section
of your device user guide or www.resmed.com.
Technical specifications
Environmental conditions
Operating temperature:
+41°F to +95°F (+5°C to +35°C)
Note: The air flow for breathing
produced by this therapy device can
be higher than the temperature of
the room. Under extreme ambient
temperature conditions (104°F/40°C)
the device remains safe.
Operating humidity:
10 to 95% relative humidity, non-
condensing
Operating altitude:
Sea level to 8,500' (2,591 m); air
pressure range 1013 hPa to 738 hPa
Storage and transport temperature:
-4°F to +140°F (-20°C to +60°C)
Storage and transport humidity:
5 to 95% relative humidity, non-
condensing
Electromagnetic compatibility
Refer to the device User Guide.
Temperature
Temperature range:
+60 to +86°F (+16 to +30°C)
Cut-out:
+106°F (+41°C)
Operating pressure range
Maximum recommended pressure
30 cm H
2
O (30 hPa)
Physical
Air tubing
Material
Length
Inner
diameter
ClimateLineAir Flexible plastic and
electrical components
6'6" (2 m) 0.6" (15 mm)
ClimateLineAir
Oxy
Flexible plastic and
electrical components
6'4" (1.9 m)
0.75" (19 mm)
Design life
Air tubing: Standard, SlimLine,
ClimateLineAir, ClimateLineAir Oxy
6 months
Symbols
The following symbols may appear on the product or
packaging.
Manufacturer. European Authorized
Representative. Catalog number. Batch code.
Prescription only (In the US, Federal law restricts
these devices to sale by or on the order of a physician).
Humidity limitation. Temperature limitation. China
pollution control logo 1. China pollution control logo 2.

8
Environmental information
This device should be disposed of separately, not as unsorted
municipal waste. To dispose of your device, you should use
appropriate collection, reuse and recycling systems available
in your region. The use of these collection, reuse and
recycling systems is designed to reduce pressure on natural
resources and prevent hazardous substances from damaging
the environment.
If you need information on these disposal systems, please
contact your local waste administration. The crossed-bin
symbol invites you to use these disposal systems. If you
require information on collection and disposal of your ResMed
device please contact your ResMed office, local distributor or
go to www.resmed.com/environment.
Limited warranty
Refer to your device user guide.

ResMed.com
378457
ResMed Ltd
1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia
See www.resmed.com for other ResMed locations worldwide. For patent and other intellectual
property information, see www.resmed.com/ip. AirSense, AirCurve, ClimateLine, HumidAir and Lumis
are trademarks of ResMed Ltd. ClimateLine is registered in U.S. Patent and Trademark Office.
© 2017 ResMed Ltd. 378457/22017-10