ResMed AirFit P10 User manual

nasal pillows system
User Guide
English
618263 Book.indb 1 9/08/2013 9:44:10 AM

Did you know?
Replacing your mask and supplies is
one of the most important steps in
maintaining effective therapy.
Replace when...
• The mask frame is damaged.
• The cushion is cracked, torn or
damaged in any way.
• The headgear is stretched and
does not return to its original form
after washing.
What to do...
Consult your equipment provider to learn
what replacement schedule may be
available through your insurance policy.
618263 Book.indb 1 9/08/2013 9:44:11 AM

i
AirFit™P10
1
2
4
5
AB
D
10
11
E
9
6
C
7
8
3
618263 Book.indb 1 9/08/2013 9:44:13 AM

ii
Mask components
Item Description
Part number
AirFit P10 AirFit P10
for Her
1 Split-strap headgear —
2 Buttonhole —
3 Fabric end —
4 Stabilizer —
5 Nasal pillows —
6 Cushion —
7 Pillows —
8 Node —
9 Vent —
10 Flexible tubing —
11 Swivel —
A Complete system 62900 62910
B Frame 62938 (1)
C Pillows system (frame system) 62920 (XS)
62921 (S)
62922 (M)
62923 (L)
D Headgear 62935 62936
E Pillows 62930 (XS)
62931 (S)
62932 (M)
62933 (L)
XS Extra Small, S Small, M Medium, L Large
618263 Book.indb 2 9/08/2013 9:44:13 AM

iii
Fitting
1
3
2
Adjustment
(a) (b)
618263 Book.indb 3 9/08/2013 9:44:15 AM

iv
Removal
Disassembly
1
2
618263 Book.indb 4 9/08/2013 9:44:16 AM

v
Reassembly
1
3
2
618263 Book.indb 5 9/08/2013 9:44:18 AM

vi
618263 Book.indb 6 9/08/2013 9:44:19 AM

English
1
English
AirFit P10
NASAL PILLOWS SYSTEM
Thank you for choosing the AirFit P10. Please read the entire manual
before use. This document provides the user instructions for the
AirFit P10 and AirFit P10 for Her masks referred to collectively as
AirFit P10 throughout this manual. AirFit P10 has blue headgear
while AirFit P10 for Her has pink headgear.
Refer to the illustrations and mask components diagram to
supplement the step-by-step procedures within this manual.
Intended Use
The AirFit P10 channels airflow noninvasively to a patient from a
positive airway pressure (PAP) device such as a continuous positive
airway pressure (CPAP) or bilevel device.
The AirFit P10 is:
to be used by patients (> 66 lb (30 kg)) for whom positive airway
pressure has been prescribed
intended for single-patient re-use in the home environment and
multipatient re-use in the hospital/institutional environment.
Using your mask
When using your mask with ResMed CPAP or bilevel devices that
have mask setting options, refer to the Technical specifications
section in this user guide for mask selection options.
For a full list of compatible devices for this mask, see the
Mask/Device Compatibility List on www.resmed.com on the
Products page under Service & Support. If you do not have internet
access, please contact your ResMed representative.
Notes:
This mask is not compatible for use with ResMed AutoSet
CS™ 2 and VPAP™ Adapt SV devices.
SmartStart may not operate effectively when using this mask
with some CPAP or bilevel devices that have this feature.

2
If you experience nasal dryness or irritation, using a humidifier is
recommended.
GENERAL WARNINGS
The mask must be used under qualified supervision for users
who are unable to remove the mask by themselves. The
mask may not be suitable for those predisposed to
aspiration.
The vent must be kept clear.
The mask should only be used with CPAP or bilevel devices
recommended by a physician or respiratory therapist.
The mask should not be used unless the device is turned on.
Once the mask is fitted, ensure the device is blowing air.
Explanation: CPAP and bilevel devices are intended to be
used with special masks (or connectors) which have vent
holes to allow continuous flow of air out of the mask. When
the device is turned on and functioning properly, new air
from the device flushes the exhaled air out through the mask
vent holes. However, when the device is not operating,
insufficient fresh air will be provided through the mask, and
the exhaled air may be rebreathed. Rebreathing of exhaled
air for longer than several minutes can, in some
circumstances, lead to suffocation. This applies to most
models of CPAP or bilevel devices.
Follow all precautions when using supplemental oxygen.
Oxygen flow must be turned off when the CPAP or bilevel
device is not operating, so that unused oxygen does not
accumulate within the device enclosure and create a risk of
fire.
Oxygen supports combustion. Oxygen must not be used
while smoking or in the presence of an open flame. Only use
oxygen in well ventilated rooms.
At a fixed rate of supplemental oxygen flow, the inhaled
oxygen concentration varies, depending on the pressure
settings, patient breathing pattern, mask, point of application
and leak rate. This warning applies to most types of CPAP or
bilevel devices.

English
3
The technical specifications of the mask are provided for
your clinician to check that they are compatible with the
CPAP or bilevel device. If used outside specification or if
used with incompatible devices, the seal and comfort of the
mask may not be effective, optimum therapy may not be
achieved, and leak, or variation in the rate of leak, may affect
the CPAP or bilevel device function.
Discontinue using this mask if you have ANY adverse
reaction to the use of the mask, and consult your physician
or sleep therapist.
Using a mask may cause tooth, gum or jaw soreness or
aggravate an existing dental condition. If symptoms occur,
consult your physician or dentist.
As with all masks, some rebreathing may occur at low CPAP
pressures.
Refer to your CPAP or bilevel device manual for details on
settings and operational information.
Remove all packaging before using the mask.
Fitting
1. Hold the pillows away from your nose ensuring that the pillow
size (eg, M) with the left (L) and right (R) indicators are correctly
facing towards you then guide the nasal pillows into your nostrils
(L into your left nostril, R into your right nostril). Pull the headgear
over your head by holding the bottom strap and stretching it
around the back of your head. The top strap should sit
comfortably on top of your head.
Tip! There are raised logos on top of the frame so you can feel
the correct way up when fitting in the dark.
2. Move the mask away from your face then place it back to get a
comfortable fit. Ensure the nasal pillows fit securely into your
nostrils with both pillows positioned upright.
3. Finally, connect the end of the mask tubing into your device air
tubing. Your mask is now fitted and ready to use. When the
device is running, a light breeze should be felt through the vent.
To inspect the vent place a finger close but not over the entire
vent area.

4
Adjustment
To achieve a comfortable fit, adjust the split straps by spreading
them apart to loosen (a) or draw them closer together to tighten (b).
Removal
To take off your mask system, pull the mask and headgear by the
split-strap, up and over your head.
Disassembly
1. Holding the top of the mask tubing, squeeze and pull the cushion
away from the mask frame.
2. Remove the headgear from the stabilizers by holding the fabric
end of each strap and pulling out to reveal the buttonhole, then
sliding over the node and off the end of each stabilizer.
Reassembly
1. With the gray side facing out, insert each end of the headgear
strap over the stabilizers through the buttonholes. Secure in
place by wrapping each strap end up and around the nodes.
Holding the split straps, pull the headgear from the stabilizer to
ensure it is tightly secure around the nodes. Ensure the headgear
strap is not twisted.
2. Attach the pillows to the mask frame by inserting the top and
bottom clips into the correct slots (shorter clip into top slot,
longer clip into bottom slot) on the mask frame. Your mask is
now reassembled.
3. Ensure the inner walls of the nasal pillows are not compressed
or collapsed. If they are, squeeze each nasal pillow so they return
to the correct shape.
Cleaning your mask at home
Your mask and headgear should only be gently handwashed. The
mask vent may discolour over time due to dust. Follow the cleaning
instructions in this guide to maintain performance and safety of the
mask.

English
5
WARNING
Always follow cleaning instructions and use mild soap. Some
cleaning products may damage the mask, its parts and their
function, or leave harmful residual vapours that could be inhaled
if not rinsed thoroughly.
CAUTION
If any visible damage of a system component is apparent
(cracking, crazing, tears or cushion damage), the component
should be discarded and replaced.
Avoid connecting flexible PVC products (eg, PVC tubing)
directly to any part of the mask. Flexible PVC contains
elements that can be detrimental to the materials of the
mask, and may cause the components to crack or break.
Daily/After each use:
Disassemble the pillows from the frame according to the
disassembly instructions.
Thoroughly clean the separated mask components (excluding
headgear), by gently rubbing in warm (approximately 86°F/30°C)
water using mild soap.
To optimize the mask seal, facial oils should be removed from
the pillows after use.
Use a soft bristle brush to clean the vent.
Inspect each component and, if required, repeat washing until
visually clean.
Rinse all components well with drinking quality water and allow
to air dry out of direct sunlight.
When all components are dry, reassemble according to the
reassembly instructions.
Weekly:
Handwash the headgear in warm (approximately 86°F/30°C)
water using mild soap. It may be washed without being
disassembled. Rinse well and allow it to air dry out of direct
sunlight.

6
Reprocessing the mask between patients
This mask should be reprocessed when used between patients.
Cleaning, disinfection and sterilization instructions are available from
the ResMed website,
www.resmed.com/masks/sterilization/americas. If you do not have
internet access, please contact your ResMed representative.
Troubleshooting
Problem/possible cause Solution
Pillows won’t seal properly, are uncomfortable or cause red marks
Pillows may have been fitted
incorrectly, adjusted incorrectly
or the headgear is fitted
incorrectly.
Check that the nasal pillows with the
left (L) and right (R) indicators are
inserted correctly (L into your left
nostril, R into your right nostril).
Carefully follow the fitting instructions.
Readjust the headgear to ensure it is
fitted comfortably.
Inner wall position of one or both
pillows is incorrect.
Squeeze pillow sides to release inner
wall. The correct position is shown in
the reassembly instructions.
Pillows are the wrong size. Talk to your clinician.
Pillows may be dirty. Clean pillows according to the
instructions.
Headgear is too loose. Wash headgear to help it return to its
original form. Follow the washing
instructions.
Adjust the headgear split straps.
Mask too noisy
System is assembled incorrectly. Disassemble the mask, then
reassemble according to the
instructions.
System is leaking air. Refit or reposition your mask. Adjust
your headgear. Check your mask is
assembled correctly.

English
7
Problem/possible cause Solution
Vent is blocked or
dirty/discolored.
If the vent requires cleaning, use a
soft bristle brush. The vent may
discolor over time and this is not a
safety concern. Follow the cleaning
instructions in this guide to maintain
performance and safety of the mask.
Technical specifications
Pressure-flow
curve
The mask contains passive venting to protect against
rebreathing. As a result of manufacturing variations, the
vent flow rate may vary.
Pressure
(cm H2O)
Flow
(L/min)
420
829
12 37
16 43
20 49
Dead space
information
Physical dead space is the empty volume of the mask
to the end of the swivel. Using the large cushions it is
123 mL.
Therapy pressure 4 to 20 cm H2O
Resistance Drop in pressure measured (nominal)
at 50 L/min: 0.4 cm H2O
at 100 L/min: 1.4 cm H2O
Environmental
conditions
Operating temperature: +41°F to 104°F (+5°C to
+40°C)
Operating humidity: 15% to 95% non-condensing
Storage and transport temperature: -4°F to 140°F (-
20°C to +60°C)
Storage and transport humidity: up to 95% relative
humidity non-condensing

8
Gross dimensions Large:
23.23" (H) x 5.87" (W) x 1.18" (D)
(590 mm (H) x 149 mm (W) x 30 mm (D))
Mask frame system (no headgear)
Mask setting
options
For S9: Select 'Pillows'
For other devices: Select 'SWIFT' (if available),
otherwise select 'MIRAGE' as the mask option.
Notes:
The mask system does not contain PVC, DEHP or phthalates.
This product is not made with natural rubber latex.
The manufacturer reserves the right to change these
specifications without notice.
Storage
Ensure that the mask is thoroughly clean and dry before storing it for
any length of time. Store the mask in a dry place out of direct
sunlight.
Disposal
This mask does not contain any hazardous substances and may be
disposed of with your normal household refuse.

English
9
Symbols
The following symbols may appear on your product or packaging:
Catalog number Batch code
Humidity limitation Temperature limitation
Fragile, handle with care Not made with natural
rubber latex
Manufacturer European Authorized
Representative
Keep away from rain This way up
Indicates a Warning or Caution and alerts you to a possible
injury or explains special measures for the safe and effective
use of the device
Read instructions before use
Prescription only (In the US, Federal law restricts these devices
to sale by or on the order of a physician)
Polypropylene recyclable

10
Limited warranty
ResMed Ltd (hereafter ’ResMed’) warrants that your ResMed mask
system (including mask frame, cushion, headgear and tubing) shall
be free from defects in material and workmanship from the date of
purchase for the period of 90 days or in the case of disposable
masks the maximum use period. This warranty is only available to
the initial consumer. It is not transferable. If the product fails under
conditions of normal use, ResMed will repair or replace, at its option,
the defective product or any of its components. This limited warranty
does not cover: a) any damage caused as a result of improper use,
abuse, modification or alteration of the product; b) repairs carried out
by any service organization that has not been expressly authorized by
ResMed to perform such repairs; and c) any damage or
contamination due to cigarette, pipe, cigar or other smoke. Warranty
is void on product sold, or resold, outside the region of original
purchase.
Warranty claims on defective product must be made by the initial
consumer at the point of purchase.
This warranty replaces all other expressed or implied warranties,
including any implied warranty of merchantability or fitness for a
particular purpose. Some regions or states do not allow limitations on
how long an implied warranty lasts, so the above limitation may not
apply to you.
ResMed shall not be responsible for any incidental or consequential
damages claimed to have resulted from the sale, installation or use
of any ResMed product. Some regions or states do not allow the
exclusion or limitation of incidental or consequential damages, so the
above limitation may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which vary
from region to region. For further information on your warranty
rights, contact your local ResMed dealer or ResMed office.