ring Video Doorbell 3 User manual

1
Video Doorbell 3

Plug the battery in.
First, fully charge the battery by plugging
it into a power source using the provided
orange cable.
The small light on top will glow
green once fully charged.
32
1. Charge the
provided
battery.
= Charged
= Charging

Insert the battery.
After charging, insert the battery in the
bottom of your Video Doorbell until it clicks
into place.
54
2. Set up
your Video
Doorbell
in the
Ring app.

Set up your Video Doorbell
near your Wi-Fi router.
In the Ring app, select Set Up a Device.
When prompted, select Doorbells, and
follow the in-app instructions.
Your Wi-Fi password
Grab your Wi-Fi password
It’s required for the in-app setup. Write it
down below so it’s handy when you need it:
Download the Ring app.
The Ring app walks you through setting up and
managing your Video Doorbell.
Search for “Ring” in one of the app stores below,
or visit: ring.com/app
Download from
Windows Store
6 7

Try it out!
After setup, push the button on the front of
your Video Doorbell to see video from the
camera in the Ring app.
Smile, you’re on camera!
98
3. Install your
Video
Doorbell.

4 feet
(1.20 metres)
Select your install height.
Install Video Doorbell approximately four feet
(1.20 metres) above the ground for optimal
performance.
If you’re connecting to existing doorbell
wiring that’s higher than four feet, thus
limiting where you can install your new
Doorbell, use the provided wedge mount to
angle your Doorbell down.
Camera field of view
Motion detection range

Remove your
existing doorbell.
(optional)
If replacing an existing
doorbell, shut o power
at the breaker. Then
remove it from the wall
and disconnect the wires.
Your Video Doorbell is
compatible with doorbell
systems supplying 8-24
volts AC at 50 or 60Hz,
40VA max.
Do not wire your Video Doorbell to a DC-powered intercom
system or other DC power source.
Steps for wiring to an existing doorbell
Insert the
mini-level.
Insert the mini-level
into your Video
Doorbell to make
sure it’s even when
you install it.
Don’t have an in-home chime?
If you see the “No In-Home Chime” button
during setup, be sure to press it.
NO IN-HOME CHIME
To change your wiring settings after setup, go
to Device Settings > Chime Connection.
Also, consider purchasing a Ring Chime or
Chime Pro, which allow you to hear Ring alerts
from anywhere in your home.
Do you have an in-home chime?
If desired, the chime
can ring when the
button on your Ring
Doorbell is pressed.
Just follow the in-app
instructions during setup.
1312

Install the anchors. (optional)
If installing on stucco, brick, or concrete,
mark 4 drill holes. Use the provided masonry
drill bit to drill holes in your wall, then insert
the included anchors.
If you’re
installing on
wood, skip this
step and toss
the anchors in
that drawer of
stuff you
never use.
Connect the wires. (optional)
Connect the wires coming out of your wall to
the screws on the back of your
Video Doorbell.
Either wire can connect to either screw. The
order doesn’t matter.
Steps for wiring to an existing doorbell
1514

Attach the wire
extensions.
(optional)
If you have trouble
connecting the wires
coming out of your
wall to the back of
your Video Doorbell,
use the provided wire
extensions and
wire nuts.
Steps for wiring to an existing doorbell
Screw it in.
Feed all the wires (and the wire nuts,
if you used them) into your wall and
secure your Video Doorbell on the wall
using four screws.
1716

Install the
faceplate.
Place one of the
provided faceplates
on your Video
Doorbell by slotting
it in at the top and
clicking it into place.
Secure the
faceplate.
Lastly, insert one
of the provided
security screws into
the bottom, and
tighten with the star-
shaped end of the
screwdriver bit.
That’s it! Your Video
Doorbell is now
ready to use.
1918

To review your warranty coverage, please visit www.ring.com/warranty.
© 2020 Ring LLC or its aliates.
Ring and all related logos are trademarks of Ring LLC or its aliates.
For additional help, visit: ring.com/help
Or give us a call…
US 1 800 656 1918
Canada 1 855 300 7289
Worldwide [phone]
AU 1 300 205 983
NZ [phone]
For a list of all our customer support numbers,
visit: ring.com/callus

User Guide
Video Doo r be ll 3

1. Charge the battery.
Plug in the battery.
First, fully charge the battery by plugging
it into a power source using the provided
orange cable.
Thesmall light on top will glow green
once fully charged.
=Charging -Charged
2
Insertthe battery.
After charging, insert the battery in the
bottom of your Video Doorbell until it
clicks into place.
3

2. Setup your Video Doorbell.
Download the Ring app .
The Ring app walks you through setting up
and managing your Video Doorbell.
Search for "Ring" in one of the app stores
below
1
or visit ring.com/ app
~ GET ITON
,,. ./ Google Play
Please makesure you have your wifi
password ready for the next step.
4
Set up yourVideo Doorbell near
your wifi router.
In the Ring app
1 selectSet
Up a Device.
When prompted
1 selectDoorbells,
and follow the in-app instructions.
Try it out.
After setup
1 push
the button on the front of
your Video Doorbell to see video from the
camera in the Ring app.
8
If you have problems with video quality after
installation,you may need to move your router
closer to your door, or add a Ring ChimePro.
Learn more at· ri n g.com/c hime-pro 5

I.
'-....... Motion detection range
..............
---
3. Install yourVideo Doorbell.
Setyour install height.
Install your Video Doorbell approximately
four feet(1.20 metres) above the ground
for optimal performance.
If you're connecting to existing doorbell
wiring that's higher than four feet and want
to angle your Video Doorbell down for a
better view, you can purchase a Wedge Kit
online at ring.c om /accesso ri es.
Camerafield of view
I

Steps for wiring to an existing doorbell
Remove your existing doorbell. (optional)
If replacing an existing doorbell, shut off
power at the breaker. Then remove it from
the wall and disconnect the wires.
Your Video Doorbell is compatible with
doorbell systems supplying 8-24 volts AC
at 50 or 60Hz, 40VA max.
0
Do not wire you• Vdf'o Doorbc to a DC-powered
1'1tE'rc.om <:.y• tcm or other DC powPr,;ou•ce
Do you have an in-home chime?
The chime can ring when the button on
your Video Doorbell is pressed.Just follow
the in-app instructions during setup.
Don't have an in- home chime?
If you see the "No In-Home Chime" button
during setup, be sure to press it.
I NO IN-HOME CHIME I
To change your wiring settings after setup,
go to Device Settings> Chime Connection.
Also, consider purchasing a Ring Chime or
Chime Pro, which allows you to hear Ring
alerts from anywhere in your home.
8
Insert the included mini-level.
This helps to ensure the camera
is parallel to the ground when
you install your Doorbell.
I
9

Install the anchors. (optional)
If installing on stucco, brick, or concrete,
mark 4 drill holes. Use a 1/4" masonry drill
bit to drill holes in your wall, then insert
the included anchors.
If you're installing on wood, skip this step.
10
Steps for wiring to an existing doorbell
Connect the wires. (optional)
Connect the wires coming out of your
wall to the screws on the back of your
Video Doorbell.
It doesn't matter which wire goes to
each screw, as long as both screws
are connected.
11

Steps for wiring to an existing doorbell
Attach the wire extensions. (optional)
If you have trouble connecting the wires
coming out of your wall to the back of
your Video Doorbell, use the provided wire
extensions and wire nuts.
12
Screw it in.
Feed all the wires (and the wire nuts, if
you used them) into your wall and secure
your Video Doorbell on the wall using the
provided screws.
13

Install the faceplate.
Place the faceplate on your Video Doorbell
by slotting 1t in at the top and clicking it
into place.
14
•
'
I
Secure the faceplate.
Lastly, insert one of the provided security
screws into the bottom, and tighten with
the included screwdriver.
Your Video Doorbell is now ready to use.
- -
I I
I
I
·-
I
~
.... --
I
-
-------
t
A
15

Review, share
and download .
Your new device comes
with a free 30-day trial
of Ring Protect video
recording service.
To continue your
subscription and save
your videos, pleasevisit:
ring . com/protect-plans
16
17