RiverRidge Ellsworth 06-031 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® ELLSWORTH TWO DOOR SPACESAVER
ITEM #: 06-031 WHITE
ITEM #: 06-032 ESPRESSO
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be
taken in unpacking and assembling this item to keep small parts away from children.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over.
Don’t use this item for a TV stand or place heavy objects on top of item.
Always use angle-braces or anchors to secure furniture to the wall.

Send requests for missing or damaged parts replacements by email to:
customer.serv[email protected] or call toll free 1-(844)-223-5201 or order parts on lineat
www.riverridgehome.com
THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS. DO
NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. IF LOADED WITH MORE THAN 25
POUNDS PER SHELF AS THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE
SERIOUS INJURY OR DEATH.

PARTS LIST
1
1PC
TOP BOARD
2
1PC
MIDDLE CONNECTION
BOARD
3
1PC
TOP LEFT SIDE PANEL
4
1PC
TOP RIGHT SIDE PANEL
5
1PC
BOTTOM LEFT SIDE PANEL
6
1PC
BOTTOM RIGHT SIDE PANEL
7
1PC
TOP SHELF
8
1PC
BOTTOM SHELF
9
1PC
REAR BOTTOM CROSS BAR
10
1PC
REAR TOP CROSS BAR
11
1PC
FRONT TOP CROSS BAR
12
1PC
SMALL BACK PANEL
13
1PC
LARGE BACK PANEL
14
1PC
RIGHT SIDE DOOR
15
1PC
LEFT SIDE DOOR
16
1PC
UPPER BACK PANEL
17
1PC
REAR TOP CROSS BAR

A
12PCS
CAM BLOT
B
12PCS
CAM LOCK
C
38PCS
WOOD DOWEL
D
1PC
MAGNET
E
2PCS
MAGNET PLATE
F
2PCS
PLASTIC ANCHOR
G
2PCS
LONG SCREW
M4x40MM
H
2PCS
KNOB
J
2PCS
SHORT MACHINE SCREW
M4x20MM
K
4PCS
PIN
M
2PCS
SCREW
M 3 x10MM
O
2PCS
SCREW
M3x 14MM
P
4PCS
SCREW
M4x40MM
Q
6PCS
LONG MACHINE SCREW
R
1 PC
ALLEN WRENCH
TOOLSNEEDEDFORASSEMBLY : FLAT & PHILLIPSSCREWDRIVER(NOTINCLUDED)
THE USE OF POWER SCREWDRIVER ISNOT RECOMMENDED

STEP 1
STEP 1
1.Screw 4 cam bolts (A) into pre-threaded holes on top board (1).
2. Insert 4 wood dowels (C) into dowel holes on top board (1).
3. Attach magnet (D) to top board (1) by inserting 2 screws (O) through holes on magnet (D) and
tighten to top board (1).
STEP 2
STEP 2
1.Screw 4 cam bolts (A) into pre-threaded holes on middle connection board (2).
2.Insert 4 wood dowels (C) into dowel holes on middle connection board (2).

STEP 3
STEP 3
1.Screw 2 cam bolts (A) into pre-threaded holes on top left side panel (3).
2.Insert 4 wood dowels (C) into dowel holes on top left side panel (3).
STEP 4
STEP 4
1. Screw 2 cam bolts (A) into pre-threaded holes on top right side panel (4).
2. Insert 4 wood dowels (C) into dowel holes on top right side panel (4).

STEP 5
STEP 5
1.Insert 8 wood dowels (C) into dowel holes on bottom left side panel(5).
STEP 6
STEP 6
1.Insert 8 wood dowels (C) into dowel holes on bottom right side panel(6).

STEP 7
STEP 7
1. Insert 1 screw (M) through hole on magnet plate (E) and tighten to left side door (15).
2. Attach knob (H) to left side door (15) by inserting 1 screw (J) through hole on left side door(15)
and tighten to knob (H).
3. Insert 2 pins (K) into holes on each end of left side door (15).
4. Repeat above steps to assemble right side door (14).
STEP 8
STEP 8
1. Attach top shelf (7) and bottom shelf (8) to top right side panel (4) by inserting cam bolts into cam
lock holes and inserting wood dowels into dowel holes on top shelf (7) and bottom shelf (8).
2. Insert 2 cam locks (B) into cam lock holes on bottom shelf (8) and rotate clockwise tosecure
cam bolts.
3. Attach rear top cross bar (10) to top right side panel (4) by inserting 2 wood dowels(C) into
dowel holes on rear top cross bar (10).

STEP 9
STEP 9
1.Slide small back panel (12) into grooves on top right side panel (4), top shelf (7) and bottom shelf
(8).
2.Insert 2 wood dowels (C) into dowel holes on end of rear top cross bar (10).
STEP 10
STEP 10
1. Attach top left side panel (3) to pre-assembled top shelf (7) and bottom shelf (8) by inserting cam
bolts into cam lock holes and inserting wood dowels into dowel holes on top shelf (7), bottom
shelf (8) and rear top cross bar (10).
2. Insert 2 cam locks (B) into cam lock holes on the bottom shelf (8) and rotate clockwiseto
secure cam bolts.

STEP 11
STEP 11
1. Attach both doors (14), (15) to bottom shelf (8) byinserting pins into holes on bottom shelf (8).
2. Slide upper back panel (16) into grooves on top left side panel (3), top right side panel (4) and top
board (1).
3. Slide large back panel (13) into grooves on lower left side panel (3) and lower right side panel (4).
4. Attach top board (1) to top left side panel (3) and top right side panel (4) by inserting cam bolts
into cam lock holes and inserting wood dowel into dowel holes on top left side panel (3) and top
right side panel (4), and insert pin into pin hole on top board (1).
5. Insert 4 cam locks (B) into cam lock holes on top left side panel (3) and top right side panel (4)
separately and rotate clockwise to secure cam bolts.
STEP 12
STEP 12
1. Attach bottom left side panel (5) to rear bottom cross bar (9), rear top cross bar (17) and front top
cross bar (11) by inserting wood dowels into dowel holes on rear bottom cross bar (9), rear top
cross bar (17) and front top cross bar (11).
2. Insert 3 screws (Q) through holes on bottom left side panel (5) and tighten to rear bottom cross
bar (9), rear top cross bar (17) and front top cross bar (11) using allen wrench (R).
3. Repeat above steps to attach bottom right side panel (6) to rear bottom cross bar (9), rear top
cross bar (17) and front top cross bar (11).
4. Insert 2 wood dowels (C) into dowel holes on rear top cross bar (17) and front top cross bar (11).

STEP 13
STEP 13
1. Attach middle connection board (2) to bottom left side panel (5) and bottom right side panel (6),
rear top cross bar (17) and front top cross bar (11) by inserting wood dowels into dowel holes
on middle connection board (2).
STEP 14
STEP 14
1.Insert 4 screws (P) through holes on middle connection board (2) and tighten to bottom left side
panel (5) and bottom right side panel (6).

STEP 15
STEP 15
1.Place top portion onto middle connection board (2) by inserting wood dowels into dowel holes
and cam bolts into cam lock holes on end of both top side panels (3) and (4).
2.Insert 4 cam lock (B) into cam lock holes on both top side panel (3) and (4) and rotate clockwise
to secure cam bolts.
STEP 16
STEP 16
1.Place drawing with hole positions on wall in desired position and drill 2 holes through hole
positions on drawing.
2.Insert 2 plastic anchors (F) into holes on wall and attach cabinet in place by inserting 2 long
screws (G) through holes on back top cross bar (10) and tighten to wall.

ENJOY YOUR NEW RiverRidge® CABINET NOW!
Attention Adults: Cabinet should be checked periodically for damage or loose screws/parts. Take
appropriate action necessary to correct hazards such as tightening of screws and taking any
damaged parts away from children.
Warning Please make sure your item is secured to the wall, per
assembly instructions.
Thank you for purchasing this RiverRidge® Kids Products item. We hope you enjoy it and
consider purchasing other RiverRidge® items.
Send requests for missing or damaged parts replacements by email to:
[e-mail] or call toll free 1-(844)-223-5201 or order parts on lineat
www.riverridgehome.com
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016.

INSTRUCCIONES DE ENSAMBLAJE
AHORRADOR DE ESPACIO DE DOS PUERTAS ELLSWORTH RiverRidge®
ARTÍCULO N.°: 06-031 BLANCO
ARTÍCULO N.°: 06-032 CAFÉ ESPRESSO
REQUIERE QUE UN ADULTO REALICE EL ENSAMBLAJE
Este producto requiere que un adulto lleve a cabo el ensamblaje debido a las piezas pequeñas.
Debe tener cuidado al desempacar y ensamblar este artículo para mantener las piezas
pequeñas alejadas de los niños.
ADVERTENCIA VEA LA ADVERTENCIA COMPLETA
EN LA PÁGINA 2
Los niños pequeños pueden resultar gravemente heridos o muertos si el mueble
vuelca. No utilice este artículo como soporte para el televisor ni coloque objetos
pesado sobre él.
Siempre utilice abrazaderas de ángulo o anclajes para fijar el mueble a la pared.

Envíe las solicitudes de reemplazos de piezas faltantes o dañadas por correo electrónico a:
[e-mail] o llame sin costo al 1-(844)-223-5201, o bien pida las piezas
en línea en www.riverridgehome.com
ESTA UNIDAD DE REPISAS PUEDE GUARDAR HASTA 25 LIBRAS POR REPISA O UN TOTAL
DE 75 LIBRAS. NO CARGUE CADA REPISA CON MÁS DE 25 LIBRAS. SI SE CARGA CON MÁS
DE 25 LIBRAS POR REPISA ESTO PUEDE DAÑAR LA REPISA Y PUEDE OCASIONAR
LESIONES GRAVES O INCLUSO LA MUERTE.

LISTA DE PIEZAS
1
1 PIEZA
TABLERO SUPERIOR
2
1 PIEZA
TABLERO DE CONEXIÓN
MEDIA
3
1 PIEZA
PANEL IZQUIERDO
SUPERIOR
4
1 PIEZA
PANEL DERECHO SUPERIOR
5
1 PIEZA
PANEL IZQUIERDO INFERIOR
6
1 PIEZA
PANEL DERECHO INFERIOR
7
1 PIEZA
REPISA SUPERIOR
8
1 PIEZA
REPISA INFERIOR
9
1 PIEZA
BARRA TRANSVERSAL
INFERIOR TRASERA
10
1 PIEZA
BARRA TRANSVERSAL
SUPERIOR TRASERA
11
1 PIEZA
BARRA TRANSVERSAL
SUPERIOR DELANTERA
12
1 PIEZA
PANEL TRASERO PEQUEÑO
13
1 PIEZA
PANEL TRASERO GRANDE
14
1 PIEZA
PUERTA DERECHA
15
1 PIEZA
PUERTA IZQUIERDA
16
1 PIEZA
PANEL TRASERO SUPERIOR
17
1 PIEZA
BARRA TRANSVERSAL
SUPERIOR TRASERA

A
12 PIEZAS
PERNO DE ANCLAJE
B
12 PIEZAS
PESTILLO DE LEVA
C
38 PIEZAS
PASADOR DE MADERA
D
1 PIEZA
IMÁN
E
2 PIEZAS
PLACA DE IMÁN
F
2 PIEZAS
ANCLAJE PLÁSTICO
G
2 PIEZAS
TORNILLO LARGO M
4 x 40 MM
H
2 PIEZAS
PERILLA
J
2 PIEZAS
TORNILLO PARA
METAL CORTO
M 4 x 20 MM
K
4 PIEZAS
PASADOR
M
2 PIEZAS
TORNILLO
M 3 x 10 MM
O
2 PIEZAS
TORNILLO
M 3 x 14 MM
P
4 PIEZAS
TORNILLO
M 4 x 40 MM
Q
6 PIEZAS
TORNILLO PARA
METAL LARGO
R
1 PIEZA
LLAVE ALLEN
HERRAMIENTAS NECESARIAS PARA EL ENSAMBLAJE: DESTORNILLADOR PLANO Y PHILLIPS
(NO INCLUIDO) NO SE RECOMIENDA EL USO DE UN DESTORNILLADOR ELÉCTRICO

PASO 1
PASO 1
1. Atornille los 4 pernos de anclaje (A) en los agujeros previamente roscados del tablero
superior (1).
2. Inserte los 4 pasadores de madera (C) en los agujeros para los pasadores del tablero
superior (1).
3. Fije el imán (D) al tablero superior (1) al insertar 2 tornillos (O) a través de los agujeros
en el imán (D) y apriete al tablero superior (1).
PASO 2
PASO 2
1. Atornille los 4 pernos de anclaje (A) en los agujeros previamente roscados en el tablero de
conexión media (2).
2. Inserte los 4 pasadores de madera (C) en los agujeros para los pasadores en el tablero de
conexión media (2).

PASO 3
PASO 3
1. Atornille los 2 pernos de anclaje (A) en los agujeros previamente roscados del panel izquierdo
superior (3).
2. Inserte 4 pasadores de madera (C) en los agujeros para los pasadores en el panel izquierdo
superior (3).
PASO 4
PASO 4
1. Atornille los 2 pernos de anclaje (A) en los agujeros previamente roscados en el panel derecho
superior (4).
2. Inserte 4 pasadores de madera (C) en los agujeros para los pasadores en el panel derecho
superior (4).

PASO 5
PASO 5
1. Inserte 8 pasadores de madera (C) en los agujeros para los pasadores del panel
izquierdo inferior (5).
PASO 6
PASO 6
1. Inserte 8 pasadores de madera (C) en los agujeros para los pasadores en el panel
derecho inferior (6).