RiverRidge Madison 06-111 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® Madison Single Door Floor Cabinet
ITEM#: 06-111 White
ITEM#: 06-122 Gray
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER SHELF OR TOP BOARD FOR A
TOTAL OF 80 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 20 POUNDS OR 80
POUNDS TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 20 POUNDS PER SHELF
OR 80 POUNDS TOTAL WEIGHT, SHELF MAY TIP FROM THE WALL AND CAUSE SERIOUS
INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC
Bottom Board
3
1PC
Left Side Panel
4
1PC
Right Side Panel
5
1PC
Cross Bar
6
1PC
Shelf
7
1PC
Adjustable Shelf
8
1PC
Door
9
1PC
Back Board

PARTS LIST
NO
PARTS
QTY
DESCRIPTION
A
12PCS
Cam Bolt
B
12PCS
Cam Lock
C
12PCS
Wood Dowel
D
4PCS
Shelf Holder
E
2PCS
Hinge
F
1PCS
Handle
G
12PCS
Screw (4x12mm)
H
1PC
Screw (4x10mm)
I
1PC
Adjustable Anchor Bracket
J
12PCS
Screw (2.5x10mm)
K
1PC
Plastic Anchor
L
1PC
Screw (4x30mm)
M
1PC
Silicon pad
N
2PCS
Screw (3.5x12mm)
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PIECES ARE MISSING OR DAMAGED
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.

STEP 1
1. Screw 4 cam bolts (A) into cam bolt holes on top board (1).
2. Attach bracket (I) to shelf (6) by inserting 1 screw (H) through hole on bracket (I), then
tighten to shelf (6).
STEP 2
1. Screw 4 cam bolts (A) into cam bolt holes on left side panel (3).
2. Screw 4 cam bolts (A) into cam bolt holes on right side panel (4).
STEP 3
1. Insert 6 wood dowels (C) into wood dowel holes on left side panel (3).
2. Attach left side panel (3) to cross bar (5), shelf (6) and bottom board (2) by inserting wood
dowels (C) into wood dowel holes on cross bar (5) and inserting cam bolts (A) into cam lock
holes on shelf (6) and bottom board (2).
3. Insert 4 cam locks (B) into cam lock holes on shelf (6) and bottom board (2) then rotate
clockwise to secure cam bolts in place.
4. Repeat above steps to assemble right side panel (4) to cross bar (5), shelf (6) and bottom
board (2).

STEP 4
1. Attach top board (1) to left side panel (3) and right side panel (4) by inserting cam bolts into
cam lock holes on left side panel (3) and right side panel (4).
2. Insert 4 cam locks (B) into cam lock holes on left side panel (3) and right side panel (4),
then rotate clockwise to secure cam bolts in place.
STEP 5
1. Attach back board (9) to cabinet by inserting 12 screws (J) through holes on back board
(9), then tighten to cabinet.

STEP 6
1. Attach 2 hinges (E) to door (8) by inserting 4 screws (G) through holes on hinges, then
tighten to door (8).
2. Attach handle (F) to door (8) by inserting 2 screws (N) through holes on handle (F), then
tighten to door (8).
3. Stick 1 silicon pad (M) on handle (F) to prevent scratches on shelf edge when door is
closed.
STEP 7
1. Attach door (8) to cabinet by inserting 8 screws (G) through holes on hinges, then tighten to
right side panel (4).
2. Note: Tightening screw in position “a” will adjust door up or down; tightening screw in
position “b” will adjust door to or from cabinet and tightening screw in position “c” will adjust
door side to side.
Door Adjustments

STEP 8
Option #1: Securing to Drywall
1. Position cabinet against wall in desired location. Using a pencil, make small mark on wall
through hole on bracket (I). Move cabinet away from wall and screw plastic anchor (K) into
wall on pencil mark.
2. Place cabinet against wall, insert screw (L) through hole on bracket (I), then tighten to
plastic anchor (K).
Option #2: Securing to Drywall and Wood Stud
1. Position cabinet against wall in desired location. Insert screw (L) through hole on bracket (I),
then tighten through drywall and into wood stud.
*Tip: Anchor bracket (I) can be adjusted to correct distance from wall to cabinet as needed. Once adjusted,
be sure to re-tighten bracket inside cabinet for stability.
STEP 9
1. Insert 4 shelf holders (D) into desired shelf position.
2. Place adjustable shelf (7) onto shelf holders (D).

ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016