RiverRidge Somerset 06-037 User manual

ASSEMBLY INSTRUCTIONS
Somerset Single Door Floor Cabinet
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75
POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR 75 POUNDS
TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 25 POUNDS PER SHELF OR 75
POUNDS TOTAL WEIGHT, SHELF MAY TIP FROM WALL AND CAUSE SERIOUS INJURY
OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Right Side Panel
2
1PC
Left Side Panel
3
1PC
Cross Bar
4
1PC
Bottom Board
5
1PC
Top Board
6
1PC
Back Board
7
1PC
Door
8
1PC
Drawer Front Board
9
1PC
Drawer Left Side Panel
10
1PC
Drawer Right Side Panel
11
1PC
Drawer Back Board
12
1PC
Drawer Bottom Board
13
1PC
Shelf
14
1PC
Left Support Board
15
1PC
Right Support Board

NO
PARTS
QTY
DESCRIPTION
A
18PCS
Wood Dowel
B
18PCS
Cam Bolt
C
18PCS
Cam Lock
D
10PCS
Screw (3x12mm)
E
2PCS
Hinge
F
1PC
Magnet Plate
G
13PCS
Screw (2.5x12mm)
H
1 SET
Magnet with 2 Screws
I
4PCS
Shelf Holder
J
4PCS
Machine Screw (4x12mm)
K
2PCS
Handle
L
4PCS
Screw (4x35mm)
N
1PC
Plastic Anchor
O
1PC
Screw (4x30mm)
P
1PC
Adjustable Anchor Bracket
R
1PC
Screw (4x14mm)
S
8PCS
Screw (3.5x12mm)
T
1 SET
Drawer Slides (Attach to Side Panel)
U
1 SET
Drawer Slides (Attach to Drawer)
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED

STEP 1
1. Attach drawer left side panel (9) to drawer back board (11) by inserting 2 screws (L)
through holes on drawer left side panel (9), then tighten into drawer back board (11).
2. Attach drawer right side panel (10) to drawer back board (11) by inserting 2 screws (L)
through holes on drawer right side panel (10), then tighten into drawer back board (11).
3. Slide drawer bottom board (12) into grooves on drawer left side panel (9) and right side
panel (10) and drawer back board (11).
STEP 2
1. Screw 2 cam bolts (B) into cam bolt holes on drawer front board (8).
2. Insert 4 wood dowels (A) into dowel holes on drawer front board (8).
3. Attach drawer front board (8) to drawer left side panel (9), drawer right side panel (10) and
drawer bottom board (12) by inserting cam bolts (B) and wood dowels (A) into holes on
drawer left side panel (9) and drawer right side panel (10) and inserting edge of drawer
bottom board (12) into groove on drawer front board (8).
4. Insert 2 cam locks (C) into cam lock holes on drawer left side panel (9) and drawer right
side panel (10) and rotate clockwise to secure cam bolts (B).
5. Attach 1 handle (K) to drawer front board (8) by inserting 2 machine screws (J) through
holes on drawer front board (8) and tighten to handle (K).

STEP 3
1. Attach drawer slides (U) to drawer right side panel (10) by inserting 2 wood screws (S)
through holes on drawer slides (U), then tighten into drawer right side panel (10).
2. Attach drawer slides (U) to drawer left side panel (9) by inserting 2 screws (S) through
holes on drawer slides (U), then tighten into drawer left side panel (9).
STEP 4
1. Insert 2 wood dowels (A) into dowel holes on left support board (14).
2. Screw 3 cam bolts (B) into cam bolt holes on left support board (14).
3. Insert 2 wood dowels (A) into dowel holes on right support board (15).
4. Screw 3 cam bolts (B) into cam bolt holes on right support board (15).
5. Attach 2 hinges (E) to left support board (14) by inserting 4 screws (D) through holes on
hinges (E), then tighten to left support board (14).

STEP 5
1. Attach left support board (14) to left side panel (2) by inserting cam bolts into cam lock
holes and inserting wood dowels into dowel holes on the left side panel (2).
2. Insert 3 cam locks (C) into cam lock holes on left side panel (2), then rotate clockwise to
secure cam bolts in place.
3. Attach drawer slides (T) to left side panel (2) by inserting 2 screws (S) through holes on
drawer slides (T), then tighten to left side panel (2).
4. Repeat above steps to assemble right side panel (1) and right support board (15).
5. Attach magnet plate (F) to door (7) by inserting 2 screws (D) through holes on magnet
plate (F), then tighten to door (7).
6. Attach handle (K) to door (7) by screwing 2 machine screws (J) through holes on door (7),
then tighten to handle (K).

STEP 6
1. Screw 6 cam bolts (B) into cam bolt holes on left side panel (2) and right side panel (1).
2. Insert 6 wood dowels (A) into dowel holes on left side panel (2) and right side panel (1).
3. Attach cross bar (3) to left side panel (2) by inserting wood dowel (A) and cam bolt (B) into
holes on cross bar (3) and insert 1 cam lock (C) into cam lock hole on cross bar (3) and
rotate clockwise to secure cam bolt (B) in place.
4. Attach bottom board (4) to left side panel (2) by inserting 2 wood dowels (A) and 2 cam
bolts (B) into holes on bottom board (4), then insert 2 cam locks (C) into cam lock holes on
bottom board (4) and rotate clockwise to secure cam bolts (B) in place.
5. Repeat above steps to attach right side panel (1) to cross bar (3) and bottom board (4).
6. Attach magnet (H) to cross bar (3) by inserting 2 magnet screws through holes on magnet
(H), then tighten into cross bar (3).

STEP 7
1. Insert 1 screw (R) through adjustable anchor bracket (P) into hole on top board (5).
2. Screw 4 cam bolts (B) into cam bolt holes on top board (5).
3. Insert 4 wood dowels (A) into dowel holes on top of left side panel (2) and right side
panel (1).
4. Attach top board (5) to left side panel (2) and right side panel (1) by inserting 4 wood
dowels (A) into dowel holes on top board (5), then insert 4 cam bolts (B) into holes on left
side panel (2) and right side panel (1).
5. Insert 2 cam locks (C) into cam lock holes on left side panel (2), then rotate clockwise to
secure cam bolts (B) in place.
6. Insert 2 cam locks (C) into cam lock holes on right side panel (1), then rotate clockwise to
secure cam bolts (B) in place.
STEP 8
1. Attach back board (6) to pre-assembled cabinet by inserting 13 screws (G) through holes
on back board (6), then tighten to cabinet.

STEP 9
Option #1: Securing to Drywall
1. Position cabinet against wall in desired location. Using a pencil, make small mark on wall
through hole on bracket (P). Move cabinet away from wall and screw 1 plastic anchor (N) into
wall on pencil mark.
2. Place cabinet against wall, insert 1 screw (O) through hole on metal bracket (P), then
tighten to plastic anchor (N).
Option #2: Securing to Drywall and Wood Stud
1. Position cabinet against wall in desired location. Insert 1 screw (O) through hole on metal
bracket (P), then tighten through drywall and into wood stud.
* Tip: Anchor bracket (P) can be adjusted to correct distance from wall to cabinet as needed. Once
adjusted, be sure to re-tighten bracket inside cabinet for stability.
STEP 10
1. Place drawer into cabinet by inserting 2 drawer slides on drawer into 2 drawer slides
attached to cabinet.
2. Attach door (7) to left side panel (2) by inserting 4 screws (D) through holes on metal
hinges (E), then tighten into door (7).

STEP 11
1. Insert 4 shelf holders (I) into holes on left side panel (2) and right side panel (1) at desired
shelf height.
2. Place shelf (13) onto shelf holders (I).
ATTENTION ADULTS: Cabinet should be checked periodically for damage or loose
screws/parts. Take appropriate action necessary to correct hazards such as tightening
of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new cabinet!