RiverRidge Ellsworth 06-031 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® Ellsworth Two Door Spacesaver
ITEM #: 06-031 White
ITEM #: 06-032 Espresso
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75
POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. IF LOADED WITH
MORE THAN 25 POUNDS PER SHELF AS THIS MAY CAUSE DAMAGE TO THE SHELF AND
MAY CAUSE SERIOUS INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC
Middle Connection Board
3
1PC
Top Left Side Panel
4
1PC
Top Right Side Panel
5
1PC
Bottom Left Side Panel
6
1PC
Bottom Right Side Panel
7
1PC
Top Shelf
8
1PC
Bottom Shelf
9
1PC
Rear Bottom Cross Bar
11
1PC
Front Top Cross Bar
12
1PC
Small Back Panel
13
1PC
Large Back Panel
14
1PC
Right Side Door
15
1PC
Left Side Door
16
1PC
Upper Back Panel
17
1PC
Rear Top Cross Bar

PARTS LIST
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement parts at no cost to you, email [e-mail], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
NO
PARTS
QTY
DESCRIPTION
A
12PCS
Cam Bolt
B
12PCS
Cam Lock
C
34PCS
Wood Dowel
D
1PC
Magnet
E
2PCS
Magnet Plate
F
2PCS
Plastic Anchor
G
2PCS
Screw (4x30mm)
H
2PCS
Knob
J
2PCS
Machine Screw (4x18mm)
K
4PCS
Metal Pin
M
2PCS
Screw (3x10mm)
O
2PCS
Screw (3x14mm)
P
4PCS
Screw (4x35mm)
Q
6PCS
Long Machine Screw
R
1PC
Allen Wrench
S
2PCS
Adjustable Anchor Bracket
T
2PCS
Screw (4x10mm)

STEP 1
1. Screw 4 cam bolts (A) into cam bolt holes on top board (1).
2. Insert 4 wood dowels (C) into dowel holes on top board (1).
3. Attach magnet (D) to top board (1) by inserting 2 screws (O) through holes on magnet (D)
and tighten to top board (1).
4. Insert 2 screws (T) through holes on adjustable anchor brackets (S), then tighten to top
board (1).
STEP 2
1. Screw 4 cam bolts (A) into cam bolt holes on middle connection board (2).
2. Insert 4 wood dowels (C) into dowel holes on middle connection board (2).

STEP 3
1. Screw 2 cam bolts (A) into cam bolt holes on top left side panel (3).
2. Insert 4 wood dowels (C) into dowel holes on top left side panel (3).
STEP 4
1. Screw 2 cam bolts (A) into cam bolt holes on top right side panel (4).
2. Insert 4 wood dowels (C) into dowel holes on top right side panel (4).

STEP 5
1. Insert 8 wood dowels (C) into dowel holes on bottom left side panel (5).
STEP 6
1. Insert 8 wood dowels (C) into dowel holes on bottom right side panel (6).

STEP 7
1. Insert 1 screw (M) through hole on magnet plate (E) and tighten to left side door (15).
2. Attach knob (H) to left side door (15) by inserting 1 screw (J) through hole on left side
door (15) and tighten to knob (H).
3. Insert 2 pins (K) into holes on each end of left side door (15).
4. Repeat above steps to assemble right side door (14).
STEP 8
1. Attach top shelf (7) and bottom shelf (8) to top right side panel (4) by inserting cam bolts
into cam lock holes and inserting wood dowels into dowel holes on top shelf (7) and
bottom shelf (8).
2. Insert 2 cam locks (B) into cam lock holes on bottom shelf (8) and rotate clockwise to
secure cam bolts.

STEP 9
1. Slide small back panel (12) into grooves on top right side panel (4), top shelf (7) and
bottom shelf (8).
STEP 10
1. Attach top left side panel (3) to pre-assembled top shelf (7) and bottom shelf (8) by
inserting cam bolts into cam lock holes and inserting wood dowels into dowel holes on
top shelf (7) and bottom shelf (8).
2. Insert 2 cam locks (B) into cam lock holes on the bottom shelf (8) and rotate clockwise to
secure cam bolts.

STEP 11
1. Attach both doors (14), (15) to bottom shelf (8) by inserting pins into holes on bottom shelf (8).
2. Slide upper back panel (16) into grooves on top left side panel (3), top right side panel (4)
and top board (1).
3. Slide large back panel (13) into grooves on top left side panel (3) and top right side panel (4).
4. Attach top board (1) to top left side panel (3) and top right side panel (4) by inserting cam
bolts into cam lock holes, wood dowels into dowel holes on top left side panel (3) and top
right side panel (4), and inserting pins into pin holes on top board (1).
5. Insert 4 cam locks (B) into cam lock holes on top left side panel (3) and top right side
panel (4) separately and rotate clockwise to secure cam bolts.
STEP 12
1. Attach bottom left side panel (5) to rear bottom cross bar (9), front top cross bar (11) and
rear top cross bar (17) by inserting wood dowels into dowel holes on rear bottom cross
bar (9), front top cross bar (11) and rear top cross bar (17).
2. Insert 3 screws (Q) through holes on bottom left side panel (5) and tighten to rear bottom
cross bar (9), front top cross bar (11) and rear top cross bar (17) using Allen wrench (R).
3. Repeat above steps to attach bottom right side panel (6) to rear bottom cross bar (9),
front top cross bar (11) and rear top cross bar (17).
4. Insert 2 wood dowels (C) into dowel holes on front top cross bar (11) and rear top cross
bar (17).

STEP 13
1. Attach middle connection board (2) to bottom left side panel (5) and bottom right side
panel (6), front top cross bar (11) and rear top cross bar (17) by inserting wood dowels
into dowel holes on middle connection board (2).
STEP 14
1. Insert 4 screws (P) through holes on middle connection board (2) and tighten to bottom
left side panel (5) and bottom right side panel (6).

STEP 15
1. Place top portion onto middle connection board (2) by inserting wood dowels into dowel
holes and cam bolts into cam lock holes on end of both top side panels (3) and (4).
2. Insert 4 cam locks (B) into cam lock holes on both top side panel (3) and (4) and rotate
clockwise to secure cam bolts.
STEP 16
Option #1: Securing to Drywall
1. Position spacesaver against wall in desired location. Using a pencil, make 2 small marks on
wall through holes on brackets (S). Move cabinet away from wall and screw 2 plastic anchors
(F) into wall on pencil marks.
2. Place cabinet against wall, insert 2 screws (G) through holes on brackets (S), then tighten
to plastic anchors (F).
Option #2: Securing to Drywall and Wood Stud
1. Position spacesaver against wall in desired location. Insert 2 screws (G) through holes on
brackets (S), then tighten through drywall and into wood stud.
*Tip: Anchor bracket (S) can be adjusted to correct distance from wall to cabinet as needed. Once adjusted,
be sure to re-tighten bracket inside cabinet for stability.

ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016