RiverRidge MEDORD 06-102 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® Medford Single Door Floor Cabinet
ITEM #: 06-102 White
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS CABINET WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS.
DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR 75 POUNDS TOTAL
WEIGHT. IF OVERLOADED WITH MORE THAN 25 POUNDS PER SHELF OR 75 POUNDS
TOTAL WEIGHT CABINET MAY TIP FROM WALL AND CAUSE SERIOUS INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC
Left Side Panel
3
1PC
Right Side Panel
4
1PC
Cross Bar
5
1PC
Back Board
6
1PC
Door
7
1PC
Adjustable Shelf
8
1PC
Bottom Board
9
1PC
Drawer Front Board
10
1PC
Drawer Left Side Panel
11
1PC
Drawer Right Side Panel
12
1PC
Drawer Back Board
13
1PC
Drawer Bottom Board

NO
PARTS
QTY
DESCRIPTION
A
10PCS
Cam Bolt (5x35mm)
B
10PCS
Cam Lock (15x10mm)
C
4PCS
Wood Dowel
D
1PC
Magnet
E
6PCS
Screw (3x14mm)
F
1PC
Adjustable Anchor Bracket
G
1PCS
Screw (3x10mm)
H
4PCS
Shelf Holder
I
4PCS
Screw (4x35mm)
J
1PC
Magnet Plate
K
2PCS
Door Pin
L
2PCS
Screw (4x25mm)
M
2PCS
Knob
N
1PC
Screw (4x30mm)
O
1PC
Plastic Anchor
P
4PCS
Plastic Bracket
Q
4PCS
Cam Bolt (5x25mm)
R
4PCS
Cam Lock (12x10mm)
S
8PCS
Screw (3x12mm)
T
1PC
Drawer Slide (attach to left side panel)
U
1PC
Drawer Slide (attach to right side panel)
V
1PC
Drawer Slide (attach to drawer right side panel)
W
1PC
Drawer Slide (attach to drawer left side panel)
X
1PC
Screw (4x12mm)
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.

STEP 1
1. Screw 4 cam bolts (A) into cam bolt holes on top board (1).
2. Attach 1 metal bracket (F) to top board (1) by inserting 1 screw (X) through hole on metal
bracket (F) and tighten to top board (1).
3. Attach magnet plate (J) to door (6) by inserting 1 screw (G) through hole on magnet plate (J)
and tighten to door (6)
4. Attach 1 knob (M) to door (6) by inserting 1 screw (L) through hole on door (6) and tighten to
knob (M).
5. Insert 2 door pins (K) into holes on door (6).
STEP 2
1. Screw 3 cam bolts (A) into cam bolt holes on left side panel (2).
2. Attach drawer slide (T) to left side panel (2) by inserting 2 screws (S) through screw holes on
drawer slide (T) and tighten to left side panel (2).
3. Screw 3 cam bolts (A) into cam bolt holes on right side panel (3).
4. Attach drawer slide (U) to right side panel (3) by inserting 2 screws (S) through screw holes
on drawer slide (U) and tighten to right side panel (3).

STEP 3
1. Attach magnet (D) to cross bar (4) by inserting 2 screws (E) through holes on magnet (D)
and tighten to cross bar (4).
2. Insert 2 wood dowels (C) into wood dowel holes on left side panel (2).
3. Attach cross bar (4) and bottom board (8) to left side panel (2) by inserting wood dowels (C)
into wood dowel holes on cross bar (4) and bottom board (8).
4. Insert 3 cam locks (B) into cam lock holes on cross bar (4) and bottom board (8), then rotate
clockwise to secure cam bolts in place.
STEP 4
1. Attach door (6) to cross bar (4) and bottom board (8) by inserting door pin (K) into door pin
holes on cross bar (4) and bottom board (8).

STEP 5
1. Insert 2 wood dowels (C) into wood dowel holes on cross bar (4) and bottom board (8).
2. Attach right side panel (3) to cross bar (4) and bottom board (8) by inserting wood dowels (C)
and cam bolts (A) into wood dowel holes and cam lock holes on cross bar (4) and bottom
board (8).
3. Insert 3 cam locks (B) into cam lock holes on cross bar (4) and bottom board (8), then rotate
clockwise to secure cam bolts in place.
STEP 6
1. Slide back board (5) into grooves on left side panel (2), right side panel (3) and bottom board
(8).
2. Attach top board (1) to left side panel (2), right side panel (3) and back board (5) by aligning
groove on top board (1) with back board (5) and inserting cam bolts (A) into cam lock holes
on left side panel (2) and right side panel (3).
3. Insert 4 cam locks (B) into cam lock holes on left side panel (2) and right side panel (3), then
rotate clockwise to secure cam bolts in place.

STEP 7
1. Screw 4 cam bolts (Q) into cam bolt holes on drawer front board (9).
2. Attach drawer left side panel (10) and drawer right side panel (11) to drawer back board (12)
by inserting 4 screws (I) through holes on drawer left side panel (10) and drawer right side
panel (11), then tighten to drawer back board (12).
3. Slide drawer bottom board (13) into grooves on drawer left side panel (10), drawer right side
panel (11) and drawer back board (12).
STEP 8
1. Attach drawer front board (9) to drawer left side panel (10), drawer right side panel (11) and
drawer bottom board (13) by inserting cam bolts (Q) into cam lock holes on drawer left side
panel (10) and drawer right side panel (11).
2. Insert 4 cam locks (R) into cam lock holes on drawer left side panel (10) and drawer right
side panel (11) and rotate clockwise to secure cam bolts in place.
3. Attach knob (M) to drawer front board (9) by inserting 1 screw (L) through hole on drawer
front board (9) and tighten to knob (M).

STEP 9
1. Attach drawer slide (V) and (W) to bottom of assembled drawer by inserting 4 screws (S)
through holes on drawer slide (V) and (W), then tighten to bottom of assembled drawer.
STEP 10
1. Insert 4 shelf holders (H) into holes on left side panel (2) and right side panel (3), making
sure all 4 shelf holders (H) are on same level.
2. Place adjustable shelf (7) onto shelf holders (H).

STEP 11
1. Attach 4 brackets (P) to back of cabinet by inserting 4 screws (E) through holes on brackets (P)
and tighten to cabinet.
STEP 12
Option #1: Securing to Drywall
1. Position cabinet against wall in desired location. Using a pencil, make small mark on wall through
hole on bracket (F). Move cabinet away from wall and screw 1 plastic anchor (O) into wall on
pencil mark.
2. Place cabinet against wall, insert 1 screw (N) through hole on metal bracket (F), then tighten to
plastic anchor (O). Slide assembled drawer into cabinet.
Option #2: Securing to Drywall and Wood Stud
1. Position cabinet against wall in desired location. Insert 1 screw (N) through hole on metal bracket
(F), then tighten through drywall and into wood stud. Slide assembled drawer into cabinet.
*Tip: Anchor bracket (F) can be adjusted to correct distance from wall to cabinet as needed. Once adjusted,
be sure to re-tighten bracket inside cabinet for stability.

ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016