RiverRidge Madison 06-110 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge®Madison Two-Door Floor Cabinet
ITEM #: 06-110 White
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken in
unpacking and assembling this item to keep small parts away from children.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER SHELF OR TOP BOARD FOR A
TOTAL OF 60 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 20 POUNDS
OR 60 POUNDS TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 20 POUNDS
PER SHELF OR 60 POUNDS TOTAL WEIGHT, SHELF MAY TIP FROM THE WALL AND
CAUSE SERIOUS INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC
Bottom Board
3
1PC
Left Side Panel
4
1PC
Right Side Panel
5
1PC
Cross Bar
6
1PC
Adjustable Shelf
7
1PC
Left Door
8
1PC
Right Door
9
1PC
Upper Back Panel
10
1PC
Lower Back Panel

PARTS LIST
NO
PARTS
QTY
DESCRIPTION
A
8PCS
Cam Bolt
B
8PCS
Cam Lock
C
8PCS
Wood Dowel (6 x 30mm)
D
4PCS
Metal Shelf Holder
E
4PCS
Hinge
F
2PCS
Handle
G
28PCS
Screw (4 x 12mm)
H
1PC
Plastic Connection Strip
I
2PCS
Screw (4 x 14mm)
J
2PCS
Bracket
K
16PCS
Screw (2.5 x 10mm)
L
2PCS
Plastic Anchor
M
2PCS
Screw (5 x 40mm)
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY TOOL
NEEDED FOR SECURING TO WALL: POWER DRILL (NOT INCLUDED)
To order replacement parts at no cost to you, email [e-mail],
call 1-(844)-223-5201 or order parts online at www.riverridgehome.com

STEP 1
1. Screw 4 cam bolts (A) into pre-threaded holes on top board (1).
2. Attach 2 brackets (J) to top board (1) by inserting 2 screws (I) through holes on bracket (J) and
tighten to top board (1).
STEP 2
1. Screw 2 cam bolts (A) into pre-threaded holes on left side panel (3).
2. Screw 2 cam bolts (A) into pre-threaded holes on right side panel (4).
STEP 3
1. Insert 4 wood dowels (C) into wood dowel holes on left side panel (3).
2. Attach left side panel (3) to cross bar (5) and bottom board (2) by inserting wood dowels into
wood dowel holes on cross bar (5) and inserting cam bolts and wood dowels into cam lock holes and
wood dowel holes on bottom board (2).
3. Insert 2 cam locks (B) into cam lock holes on bottom board (2) and rotate clockwise to secure
cam bolts in place.
4. Repeat above steps to assemble right side panel (4) to cross bar (5) and bottom board (2).

STEP 4
1. Attach top board (1) to left side panel (3) and right side panel (4) by inserting cam bolts into
cam lock holes on left side panel (3) and right side panel (4).
2. Insert 4 cam locks (B) into cam lock holes on left side panel (3) and right side panel (4), then
rotate clockwise to secure cam bolts in place.
STEP 5
1. Attach upper back board (9) and lower back board (10) together by sliding into plastic connection
strip (H).
2. Attach upper back board (9) and lower back board (10) to cabinet by inserting 16 wood screws (K)
through holes on upper back board (9) and lower back board (10) then tighten to cabinet.

STEP 6
1. Attach 2 hinges (E) to left door (7) by inserting 4 screws (G) through holes on hinges (E) then
tighten to left door (7).
2. Attach handle (F) to left door (7) by inserting 2 screws (G) through holes on handle (F) then
tighten to left door (7).
3. Repeat above steps to assemble hinges (E) and handle (F) to right door (8).
STEP 7
1. Attach left door (7) to cabinet by inserting 8 screws (G) through holes on hinges (E) then tighten
to left side panel (3).
2. Attach right door (8) to cabinet by inserting 8 screws (G) through holes on hinges (E) then tighten
to right side panel (4).
3. Note: Tightening screw in position “a” will adjust doors up or down; tightening screw in position
“b” will adjust doors to or from cabinet and tightening screw in position “c” will adjust doors side
to side.
Door Adjustments

STEP 8
1. Place drawing with hole positions on wall you desire to mount cabinet and drill holes on wall.
2. Insert 2 plastic anchors (L) into holes on wall.
3. Align brackets on cabinet with anchors in wall and fix cabinet to wall by inserting 2 screws (M)
through hole on brackets (J) and tighten to plastic anchors (L) in wall.
STEP 9
1. Insert 4 metal holders (D) into holes at desired shelf height position.
2. Place shelf (6) on 4 metal holders (D).
ATTENTION ADULTS: Cabinet should be checked periodically for damage or loose
screws/parts. Take appropriate action necessary to correct hazards such as tightening
of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [e-mail],
call 1-(844)-223-5201 or order parts online at www.riverridgehome.com
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016