RiverRidge 02-163 User manual

ASSEMBLY INSTRUCTIONS
ITEM #: 02-163 White
RiverRidge®Book Nook
Kids Storage Bench with Cubbies
ADULT ASSEMBLY REQUIRED
WARNING
SEE FULL WARNING ON PAGE 2
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
Young children can be seriously injured or killed if furniture tips over.
Don’t use this item for a TV stand or place heavy objects on top of item.
Always use angle-braces or anchors to secure furniture to the wall.

This product is suitable for children 3 years and older.
THIS STORAGE BENCH WILL HOLD UP TO 20 POUNDS PER CUBBY AND HAS A
SEATING CAPACITY OF 75 POUNDS OR A TOTAL OF 155 POUNDS. DO NOT LOAD
EACH CUBBY WITH MORE THAN 20 POUNDS OR THE BENCH SEAT WITH MORE
THAN 75 POUNDS. IF OVERLOADED WITH MORE THAN 20 POUNDS PER CUBBY
OR 75 POUNDS ON THE BENCH SEAT, THIS MAY CAUSE DAMAGE TO THE SHELF
AND MAY CAUSE SERIOUS INJURY OR DEATH.

Top Board1PC
QTYNO DESCRIPTION
1
Middle Board1PC2
Bottom Board1PC3
Left Side Panel1PC4
Right Side Panel1PC5
Upper Slant Board1PC6
Divider Board2PCS7
Back Cross Bar1PC8
Upper Back Panel1PC9
Lower Back Panel1PC10
Wood Leg6PCS11
Cushion1PC12
PARTS LIST
1
2
3
4
5
8
9
10
11
11 11 11 11 11
12
6
7
7

Wood Dowel
Cam Bolt
Cam Lock
Cam Bolt
Screw (4x35mm)
Allen Wrench
Screw (5x40mm)
4PCS
8PCS
10PCS
14PCS
1PC
6PCS
13PCS
A
B
C
D
E
F
G
Screw (4x30mm)
Plastic Anchor
2PCS
2PCS
I
J
Screw (4x10mm)
Adjustable Anchor Bracket
2PCS
2PCS
K
M
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
PARTS LIST
NO PARTS QTY DESCRIPTION
To order replacement parts at no cost to you,email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.

STEP 1
STEP 2
1. Screw 2 cam bolts (A) into cam bolt holes on top board (1).
2. Screw 2 cam bolts (D) into cam bolt holes on top board (1), make sure cam bolts (D)
face correct direction as drawing shows.
1. Screw 2 cam bolts (D) into cam bolt holes on middle board (2), make sure cam bolts (D)
face correct direction as drawing shows.
A
A
D
D
D
D
DD
Front
11
1
D
D
DD
D
D
Front
22
2

STEP 3
STEP 4
1. Screw 4 cam bolts (A) into cam bolt holes on middle board (2)
2. Insert 2 screws (M) through holes on adjustable anchor brackets (K), then tighten to middle
board (2).
1. Screw 2 cam bolts (A) into cam bolt holes on left side panel (4).
2. Screw 2 cam bolts (A) into cam bolt holes on right side panel (5).
A
A
A
A
45
A
AK
K
M
M
A
A
2

B
DD
B
1. Attach upper slant board (6) to middle board (2) by inserting cam bolts (D) into cam lock holes on
upper slant board (6).
2. Insert 2 cam locks (B) into cam lock holes on upper slant board (6), then rotate clockwise to
secure cam bolts (D) in place.
1. Attach right side panel (5) to middle board (2) by inserting cam bolts (A) into cam lock holes on
middle board (2).
2. Insert 2 cam locks (B) into cam lock holes on middle board (2), then rotate clockwise to secure
cam bolts (A) in place.
3. Slide upper back board (9) into grooves on middle board (2) and upper slant board (6).
4. Attach left side panel (4) to middle board (2) by inserting cam bolts (A) into cam lock holes on
middle board (2). Make sure that back board (9) slides into groove on left side panel (4).
5. Insert 2 cam locks (B) into cam lock holes on middle board (2), then rotate clockwise to secure
cam bolts (A) in place.
STEP 5
STEP 6
6
2
B
A
A
B
B
B
5
4
2
9
6

1. Attach 2 divider boards (7) to middle board (2) by inserting cam bolts (A) into cam lock holes on
divider boards (7).
2. Insert 4 cam locks (B) into cam lock holes on divider boards (7), then rotate clockwise to secure
cam bolts (A) in place.
STEP 7
1. Attach 6 wood legs (11) to bottom board (3) by inserting 6 screws (F) through holes on bottom
board (3), then tighten to wood legs (11) with Allen wrench (G).
STEP 8
F
F
F
G
G
F
3
11
11
11
11
11
11
B
B
B
A
AA
A
B
7
4
2
5
7

STEP 9
1. Attach top board (1) to pre-assembled unit by inserting cam bolts (A, D) into cam lock holes on
left side panel (4) and upper slant board (6).
2. Insert 4 cam locks (B) into cam lock holes on left side panel (4) and upper slant board (6), then
rotate clockwise to secure cam bolts (A, D) in place.
STEP 10
BB
B B
1
C
CCC
C
C
C
C
E
E
E
E
E
E
EE
4
4
6
3
10
1. Slide lower back board (10) into grooves on left side panel (4), right side panel (5) and middle
board (2).
2. Insert 8 wood dowels (C) into wood dowel holes on bottom board (3).
3. Attach bottom board (3) to left side panel (4), right side panel (5), divider boards (7) and lower
back board (10) by inserting wood dowels (C) into wood dowel holes on left side panel (4),
right side panel (5) and divider boards (7). Make sure lower back board (10) slides into
groove on bottom board (3).
4. Insert 8 screws (E) through holes on bottom board (3) then tighten to left side panel (4), right
side panel (5) and divider boards (7).

STEP 11
1. Place cushion (12) on bench as shown.
STEP 12
E
E
E
E
E
8
1. Attach back cross bar (8) to back of pre-assembled bench by inserting 5 screws (E) through
holes on back cross bar (8), then tighten to back of bench.
12

STEP 13
IMPORTANT:
Keep assembly instructions for future reference.
ATTENTION ADULTS: Cabinet should be checked periodically for damage or loose
screws/parts. Take appropriate action necessary to correct hazards such as tightening
of screws and taking any damaged parts away from children.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
I
JJ
DRYWALL
WALL ANCHOR
WITH SCREW
SCREW
ONLY
DRYWALL
OPTION #2OPTION #1
WOOD
STUD
Option #1: Securing to Drywall
1. Position bench against wall in desired location. Using a pencil, make 2 small marks on wall through
holes on brackets (K). Move bench away from wall and screw 2 plastic anchors (I) into wall on
pencil marks.
2. Place bench against wall, insert 2 screws (J) through holes on brackets (K), then tighten to plastic
anchors (I).
Option #2: Securing to Drywall and Wood Stud
1. Position cabinet against wall in desired location. Insert 2 screws (J) through holes on brackets (K),
then tighten through drywall and into wood stud.
*Tip: Anchor brackets (K) can be adjusted to correct distance from wall to cabinet as needed. Once
adjusted, be sure to re-tighten brackets inside cabinet for stability.
J
J
I
I
J
K
I

Enjoy Your New RiverRidge®Storage Bench!
To order replacement parts at no cost to you,email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016
Thank you for purchasing this RiverRidge®Home item. We hope you
enjoy it and consider purchasing other RiverRidge®items.