Ronbow Signature E025234 Assembly instructions

INSTALLATION AND CARE GUIDE
FREE LED WOOD MIRROR
E025234
E025233

170627ronbow.eu | ronbow.comINSTALLATION SHEET
2
Designed By: DANELONMERONI | UNITED KINGDOM
FREE 31"/47" Free LED Wood Mirror
Model : E025233
E025234
120VAC
20A GFI
CIRCUIT BREAKER FIELD CONNECTION
Black = Ground
Red = Positive
White = Negative
Black = Ground
Red = Positive
White = Negative
LED
Wiring Diagram :
ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENCED ELECTRICIAN.
WARNING:
CAUTION: Requires 120V 20AMP circuit.
CAUTION: The LED mirror must be wired to a 20AMP GFI (ground fault interrupter) circuit breaker when
used in bathrooms and all other locations required by the national electirc code.
Note :
LED MIRROR CABINET
Figure 1.
minimum to ceiling
minimum to faucet
1”
1”
Figure 2.
Determine the ideal location of your new
mirror. Mark the pilot hole location to
mount the mirror.
Step 1 :
See Figure 1.
Drill the 5/16” pilot holes in the wall with
1-9/16” depth and place the anchors
inside the holes.
NOTE: anchors are only required when
mounting to the drywall and studs are
not available.
Step 2 :
See Figure 2.

170627ronbow.eu | ronbow.comINSTALLATION SHEET
3
Designed By: DANELONMERONI | UNITED KINGDOM
FREE 31"/47" Free LED Wood Mirror
Model : E025233
E025234
Figure 3.
Figure 4.
screw
wall
anchor
Install the screw to the anchor. Leave at
least 3/16” of screw head protruding out
from the wall.
Line up the key-holes behind the mirror,
and let the mirror rest onto the screws.
Step 3 :
Step 4 :
See Figure 3.
See Figure 4.

Wood Surfaces
Recommended Products
The fine furniture finish of your new vanity, mirror or other bathroom accessories are designed to
protect against normal home use. With proper care, your product will provide years of use and beauty
in your home.
General Care Tips
PRODUCT CARE AND MAINTENANCE
• If a spill occurs, clean and dry the surface immediately as liquid can soak through the surface and cause
greater damage.
• Do not place in direct sunlight. Exposure to sunlight may affect the appearance of your vanity, and the
finish will eventually crack.
• Keep away from direct sources of extreme temperatures as heat, cold or moisture from humidity.
Color changes, or blemishes in the wood can occur if recommended care of is not met. Try to avoid
these extremes.
• Most wood surfaces can be cleaned, or dusted, with any commercial wood cleaning product. For general
cleaning, use a non-abrasive, or lint-free cloth while dusting along the wood grain to preserve the
wood’s chacteristics.
• Pledge Orange Oil, or similar
• Orange-Glo Wood Cleaner
DISCLAIMERS: Wood naturally ages, darkens and changes color over time due to several environmental conditions that may cause materials to vary from their
original color and/or to warp, split or crack. These variations are considered to be the nature of the material in relation to their environmental exposure and may
be significant over a long period of time. The eectiveness of cleaning Ronbow product is dependant on various factors that include sunlight, smoke, moisture,
household cleaners and/or amount of cleaning product used over time. Ronbow cannot guarantee that the above Product Care & Maintenance methods will
eectively clean your product.
• Test cleaning product on small, discrete area prior to applying to entire surface.
• Wipe surfaces frequently with dry, soft, non-abrasive and lint-free towel.
• Do not allow liquids and moisture to accumulate on the surface of products.
• For warranty information, please visit our website at www.ronbow.com or contact the Customer Service
Department at [phone].

170624
40650 Encyclopedia Circle
Fremont, CA 94538
T 510.713.1188
F 510.657.9388 ronbow.eu | ronbow.com