Rosemount 2240S User manual

www.rosemount-tg.com
Reference Manual
300550EN, Rev AA
December 2010
Rosemount 2240S
Multi-Input Temperature Transmitter

Reference Manual
300550EN, Rev AA
December 2010 Rosemount 2240S
www.rosemount-tg.com
Rosemount 2240S
Multi-Input Temperature
Transmitter
Cover Photo: 2240_coverphoto.tif
NOTICE
Read this manual before working with the product. For personal and system safety, and for
optimum product performance, make sure you thoroughly understand the contents before
installing, using, or maintaining this product.
For equipment service or support needs, contact your local Emerson Process
Management/Rosemount Tank Gauging representative.
Spare Parts
Any substitution of non-recognized spare parts may jeopardize safety. Repair, e.g.
substitution of components etc, may also jeopardize safety and is under no circumstances
allowed.
Rosemount Tank Radar AB will not take any responsibility for faults, accidents, etc caused
by non-recognized spare parts or any repair which is not made by
Rosemount Tank Radar AB.
The products described in this document are NOT designed for nuclear-qualified
applications.
Using non-nuclear qualified products in applications that require nuclear-qualified hardware
or products may cause inaccurate readings.
For information on Rosemount nuclear-qualified products, contact your local Rosemount
Sales Representative.

Reference Manual
300550EN, Rev AA
December 2010 Rosemount 2240S
www.rosemount-tg.com
Table of Contents
SECTION 1
Introduction
1.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.2 Manual Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.3 Technical Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.4 Service Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.5 Product Recycling/ Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.6 Packing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.6.1 Reuse and Recycling . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.6.2 Energy recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
SECTION 2
Overview
2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.3 System Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.4 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2.5 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
SECTION 3
MST/WLS Installation
3.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2 Installation considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.3 Multiple Spot Temperature Sensor . . . . . . . . . . . . . . . . . . . . . . 3-4
3.3.1 Installation on Fixed Roof Tanks . . . . . . . . . . . . . . . . 3-4
3.3.2 Installation on Floating Roof Tanks . . . . . . . . . . . . . . 3-5
3.3.3 Custody Transfer Applications . . . . . . . . . . . . . . . . . . 3-6
3.4 Water Level Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.5 Installing a Temperature Sensor Tube . . . . . . . . . . . . . . . . . . . 3-8
SECTION 4
2240S Installation
4.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.2 Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4.3 Mechanical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4.3.1 Mounting on top of a Temperature Sensor/WLS . . . . 4-3
4.3.2 Pipe Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
4.3.3 Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
4.4 Electrical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4.4.1 Cable/Conduit Entries . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4.4.2 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4.4.3 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4.4.4 Cable Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
4.4.5 Hazardous Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
4.4.6 The Raptor Tankbus . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
4.4.7 Typical Installations . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
4.4.8 Tankbus Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
4.4.9 Daisy-chain Connection . . . . . . . . . . . . . . . . . . . . . . 4-12
4.4.10 Temperature Element Wiring . . . . . . . . . . . . . . . . . . 4-13
4.4.11 Water Level Sensor Wiring . . . . . . . . . . . . . . . . . . . 4-16

Reference Manual
300550EN, Rev AA
December 2010
Rosemount 2240S
TOC-2 Table of Contents
SECTION 5
Configuration/Operation
5.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.2.1 Configuration procedure. . . . . . . . . . . . . . . . . . . . . . . 5-2
5.2.2 Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.2.3 Configuration tools . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.3 Basic Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
5.3.1 Temperature elements . . . . . . . . . . . . . . . . . . . . . . . . 5-3
5.3.2 Water Level Sensor Calibration . . . . . . . . . . . . . . . . . 5-6
5.3.3 Water Level Sensor Measuring Range . . . . . . . . . . . 5-7
5.4 LED Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
5.4.1 Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
5.4.2 Communication LEDs . . . . . . . . . . . . . . . . . . . . . . . 5-12
5.5 Switches and reset buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
5.5.1 DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
5.5.2 Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
5.6 Configuration using TankMaster WinSetup . . . . . . . . . . . . . . . 5-15
5.6.1 Advanced Configuration. . . . . . . . . . . . . . . . . . . . . . 5-15
SECTION 6
Service and
Troubleshooting
6.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.2 Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6.2.1 Viewing Input and Holding Registers . . . . . . . . . . . . . 6-2
6.2.2 Editing Holding Registers. . . . . . . . . . . . . . . . . . . . . . 6-3
6.2.3 Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
6.2.4 Ground Fault Detection . . . . . . . . . . . . . . . . . . . . . . . 6-5
6.2.5 Reset and WLS Calibration . . . . . . . . . . . . . . . . . . . . 6-6
6.2.6 Device Error LED Signals . . . . . . . . . . . . . . . . . . . . . 6-7
6.2.7 Test and Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
6.2.8 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
6.3 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
6.3.1 Device Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15
6.3.2 Device Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
6.3.3 Device Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
6.3.4 Measurement Status for the WLS . . . . . . . . . . . . . . 6-19
6.3.5 Temperature Element Status . . . . . . . . . . . . . . . . . . 6-20
APPENDIX A
Reference Data
A.1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
A.2 Dimensional drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
A.3 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
APPENDIX B
Product Certifications
B.1 Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
B.2 EU Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
B.3 Hazardous Locations Certifications. . . . . . . . . . . . . . . . . . . . . .B-3
B.3.1 Factory Mutual US Approvals . . . . . . . . . . . . . . . . . . B-3
B.3.2 Factory Mutual Canadian Approvals . . . . . . . . . . . . .B-5
B.3.3 European ATEX Directive Information . . . . . . . . . . . . B-7
B.3.4 IECEx Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
B.4 Approval Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-11

Reference Manual
300550EN, Rev AA
December 2010 Rosemount 2240S
www.rosemount-tg.com
Section 1 Introduction
1.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-1
1.2 Manual Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-2
1.3 Technical Documentation . . . . . . . . . . . . . . . . . . . . page 1-3
1.4 Service Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-4
1.5 Product Recycling/ Disposal . . . . . . . . . . . . . . . . . . page 1-4
1.6 Packing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-4
1.1 SAFETY
MESSAGES
Procedures and instructions in this manual may require special precautions to
ensure the safety of the personnel performing the operations. Information that
raises potential safety issues is indicated by a warning symbol ( ). Refer to
the safety messages listed at the beginning of each section before performing
an operation preceded by this symbol.
Failure to follow these installation guidelines could result in death or serious
injury:
• Make sure only qualified personnel perform the installation.
• Use the equipment only as specified in this manual. Failure to do so may
impair the protection provided by the equipment.
Explosions could result in death or serious injury:
• Verify that the operating environment of the transmitter is consistent with the
appropriate hazardous locations certifications.
• Before connecting a hand held communicator in an explosive atmosphere,
make sure the instruments in the loop are installed in accordance with
intrinsically safe or non-incendive field wiring practices.
• Do not remove the gauge cover in explosive atmospheres when the circuit is
alive.
Electrical shock could cause death or serious injury.
• Use extreme caution when making contact with the leads and terminals.
Any substitution of non-recognized parts may jeopardize safety. Repair, e.g. substitution
of components etc., may also jeopardize safety and is under no circumstances allowed.

Reference Manual
300550EN, Rev AA
December 2010
Rosemount 2240S
1-2 Section 1. Introduction
1.2 MANUAL
OVERVIEW
This manual provides installation, configuration, and maintenance information
for the Rosemount 2240S Multi-input Temperature Transmitter.
Section 1: Introduction
• Manual overview
• Product recycling/disposal
• Product recycling
Section 2: Overwiew
• Introduction
• 2240S components
• Raptor system architecture
• Getting started
• Brief descripiton of installation procedure for the Rosemount 2240S
Section 3: MST/WLS Installation
• Installation considerations
• Multi Spot Thermometer
• Water Level Sensor
• Tube installation
Section 4: 2240S Installation
• Installation considerations
• Mechanical installation
• Electrical installation
Section 5: Configuration/Operation
• Introduction
• Basic configuration
• LED signals
• Switches and reset buttons
• Configuration using TankMaster WinSetup
• Advanced configuration
Section 6: Service and Troubleshooting
•Service
• Troubleshooting
Appendix A: Reference Data
• Specifications
• Dimensional drawings
• Ordering information
Appendix B: Product Certifications
• EU Conformity
• Hazardous locations certifications
• Approval drawings

Reference Manual
300550EN, Rev AA
December 2010
1-3
Rosemount 2240S
Section 1. Introduction
1.3 TECHNICAL
DOCUMENTATION
The Raptor System includes the following documents:
• Raptor Technical Description (704010EN)
• Rosemount 5900S Reference Manual (300520EN)
• Rosemount 2410 Reference Manual (300530EN)
• Rosemount 2240S Reference Manual (300550EN)
• Rosemount 2230 Reference Manual (300560EN)
• Raptor System Configuration Manual (300510EN)
• Rosemount 5300 Product Data Sheet (00813-0100-4530)
• Rosemount 5400 Product Data Sheet (00813-0100-4026)
• Rosemount 5300 Series Reference Manual (00809-0100-4530)
• Rosemount 5400 Series Reference Manual (00809-0100-4026)
• Rosemount TankMaster WinOpi Reference Manual (303028EN)
• Rosemount Raptor Installation Drawings

Reference Manual
300550EN, Rev AA
December 2010
Rosemount 2240S
1-4 Section 1. Introduction
1.4 SERVICE SUPPORT For service support contact the nearest Emerson Process
Management/Rosemount Tank Gauging representative. Contact information
can be found on the web site www.rosemount-tg.com.
1.5 PRODUCT
RECYCLING/
DISPOSAL
Recycling of equipment and packaging should be taken into consideration
and disposed of in accordance with local and national legislation/regulations.
The label below is put on Rosemount Tank Gauging products as a
recommendation to customers if scrapping is considered.
Recycling or disposal should be done following instructions for correct
separation of materials when breaking up the units.
Figure 1-1. A green label is
placed on the transmitter
housing
1.6 PACKING
MATERIAL
Rosemount Tank Radar AB is fully certified according to ISO 14001
environmental standards. By recycling the corrugated paperboard, or wooden
boxes, used for shipping our products you can contribute to take care of the
environment.
1.6.1 Reuse and
Recycling
Experience has shown that wooden boxes can be used several times for
various purposes. After careful disassembly the wooden parts may be reused.
Metal waste may be converted.
1.6.2 Energy recovery Products which have served their time may be divided into wood and metal
components and the wood can be used as fuel in sufficient ovens.
Due to its low moisture content (approximately 7%) this fuel has a higher
calorific value than ordinary wood fuel (moisture content approximately 20%).
When burning interior plywood the nitrogen in the adhesives may increase
emissions of nitrogen oxides to the air 3-4 times more than when burning bark
and splinter.
NOTE!
Landfill is not a recycling option and should be avoided.
S
E
P
A
R
A
T
E
S
T
E
E
L
&
P
L
A
S
T
I
C

Reference Manual
300550EN, Rev AA
December 2010 Rosemount 2240S
www.rosemount-tg.com
Section 2 Overview
2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-1
2.2 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-2
2.3 System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-3
2.4 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-7
2.5 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . page 2-8
2.1 INTRODUCTION The Rosemount 2240S Multi-input Temperature Transmitter can connect up
to sixteen 3- or 4-wire temperature spot elements and an integrated water
level sensor. The 2240S sends measurement data, such as temperature and
water level, via the intrinsically safe 2-wire Tankbus(1), to a Rosemount
2410 Tank Hub. Measurement data and status information can be viewed on
a PC with the Rosemount TankMaster software, on the integral display of the
2410 Tank Hub, and on a Rosemount 2230 Graphical Field Display.
Figure 2-1. System integration
Data from a group of tanks is buffered by a Rosemount 2160 Field
Communication Unit (FCU), and is distributed via the Group Bus to a
TankMaster PC, or a host system, whenever the 2160 receives a request for
data. In case no 2160 is included in the system, the 2410 can communicate
directly with the host computer.
(1) The intrinsically safe Tankbus complies with the FISCO FOUNDATION™ fieldbus standard.
TankMaster
2410 Tank Hub
Modem
Relay outputs
Secondary bus
Primary Bus
Tankbus
2230 Display
Group Bus
2240S Temperature
Transmitter
5900S Radar
Level Gauge
2160 Field
Communication Unit

Reference Manual
300550EN, Rev AA
December 2010
Rosemount 2240S
2-2 Section 2. Overview
2.2 COMPONENTS
Figure 2-2. Rosemount 2240S
components
1. Cover.
2. Glands (x 5) of type ½ - 14 NPT.
3. Lock nut for connection of Multi Spot Temperature sensors
and Water Level Sensors (MST/WLS).
4. Cover screws (x 4).
5. External ground screw.
6. M32 Cable gland (option for remote mounting).
1
2
3
4
5
6

Reference Manual
300550EN, Rev AA
December 2010
2-3
Rosemount 2240S
Section 2. Overview
2.3 SYSTEM
OVERVIEW
Raptor is a state-of-the art inventory and custody transfer radar tank level
gauging system. It is developed for a wide range of applications at refineries,
tank farms and fuel depots, and fulfills the highest requirements on
performance and safety.
The field devices on the tank communicate over the intrinsically safe Tankbus.
The Tankbus is based on a standardized fieldbus, the FISCO(1) FOUNDATION™
fieldbus, and allows integration of any device supporting that protocol. By
utilizing a bus powered 2-wire intrinsically safe fieldbus the power
consumption is minimized. The standardized fieldbus also enables integration
of other vendors’ equipment on the tank.
The Raptor product portfolio includes a wide range of components to build
small or large customized tank gauging systems. The system includes various
devices, such as radar level gauges, temperature transmitters, and pressure
transmitters for complete inventory control. Such systems are easily
expanded thanks to the modular design.
Raptor is a versatile system that is compatible with and can emulate all major
tank gauging systems. Moreover, the well-proven emulation capability
enables step-by-step modernization of a tank farm, from level gauges to
control room solutions.
It is possible to replace old mechanical or servo gauges with modern Raptor
gauges, without replacing the control system or field cabling. It is further
possible to replace old HMI/SCADA-systems and field communication
devices without replacing the old gauges.
There is a distributed intelligence in the various system units which
continuously collect and process measurement data and status information.
When a request for information is received an immediate response is sent
with updated information.
The flexible Raptor system supports several combinations to achieve
redundancy, from control room to the different field devices. Redundant
network configuration can be achieved at all levels by doubling each unit and
using multiple control room work stations.
(1) See documents IEC 61158-2 and IEC/TS 60079-27

Reference Manual
300550EN, Rev AA
December 2010
Rosemount 2240S
2-4 Section 2. Overview
Figure 2-3. Raptor system
architecture
2230 Display
2240S Temperature
Transmitter
5900S Radar
Level Gauge
2410 Tank Hub
Tankbus
5300 Level
Transmitter
5400 Level
Transmitter
3051S
Pressure
Transmitter
TRL2 Modbus
Group bus
2180 Field
Bus Modem
2160 Field
Communication Unit
TankMaster PC
Plant Host Computer
2410 Tank Hub
644
644
644
644Temperature
Transmitter
TankMaster PC
Plant Host Computer
NON-HAZARDOUS AREA HAZARDOUS AREA
2240S Temperature
Transmitter
2410 Tank Hub
5900S Radar
Level Gauge
Tankbus
Segment splitter
CUSTODY TRANSFER / INVENTORY TANK GAUGINGOPERATIONAL CONTROL

Reference Manual
300550EN, Rev AA
December 2010
2-5
Rosemount 2240S
Section 2. Overview
TankMaster HMI Software
TankMaster is a powerful Windows-based Human Machine Interface (HMI) for
complete tank inventory management. It provides configuration, service,
set-up, inventory, and custody transfer functions for Raptor systems and other
supported instruments.
TankMaster is designed to be used in the Microsoft Windows XP and Vista
environment providing easy access to measurement data from your Local
Area Network.
The TankMaster WinOpi program lets the operator monitor measured tank
data. It includes alarm handling, batch reports, automatic report handling,
historical data sampling as well as inventory calculations such as Volume,
Observed Density and other parameters. A plant host computer can be
connected for further processing of data.
The TankMaster WinSetup program is a graphical user interface for
installation, configuration and service of the different devices in the Raptor
system.
Rosemount 2160 Field Communication Unit
The 2160 Field Communication Unit (FCU) is a data concentrator that
continuously polls and stores data from field devices such as radar level
gauges and temperature transmitters in a buffer memory. Whenever a request
for data is received, the FCU can immediately send data from a group of tanks
from the updated buffer memory.
Rosemount 2410 Tank Hub
The Rosemount 2410 Tank Hub acts as a power supply to the connected field
devices in the hazardous area using the intrinsically safe Tankbus.
The 2410 collects measurement data and status information from field
devices on a tank. It has two external buses for communication with various
host systems. There are two versions of the 2410 for single tank or multiple
tanks operation. The multiple tanks version supports up to 10 tanks and 16
devices.
The 2410 is equipped with two relays which support configuration of up to 10
“virtual” relay functions allowing you to specify several source signals for each
relay.
Rosemount 5900S Radar Level Gauge
The Rosemount 5900S Radar Level Gauge is an intelligent instrument for
measuring the product level inside a tank. Different antennas can be used in
order to meet the requirements of different applications. The 5900S can
measure the level of almost any product, including bitumen, crude oil, refined
products, aggressive chemicals, LPG and LNG.
The Rosemount 5900S sends microwaves towards the surface of the product
in the tank. The level is calculated based on the echo from the surface. No
part of the 5900S is in actual contact with the product in the tank, and the
antenna is the only part of the gauge that is exposed to the tank atmosphere.
The 2-in-1 version of the 5900S Radar Level Gauge has two radar modules in
the same transmitter housing allowing two independent level measurements
using one antenna.

Reference Manual
300550EN, Rev AA
December 2010
Rosemount 2240S
2-6 Section 2. Overview
Rosemount 5300 Guided Wave Radar
The Rosemount 5300 is a premium 2-wire guided wave radar for level
measurements on liquids, to be used in a wide range of medium accuracy
applications under various tank conditions. Rosemount 5300 includes the
5301 for liquid level measurements and the 5302 for liquid level and interface
measurements.
Rosemount 5400 Radar Level Transmitter
The Rosemount 5400 is a reliable 2-wire non-contact radar level transmitter
for liquids, to be used in a wide range of medium accuracy applications under
various tank conditions.
Rosemount 2240S Multi-Input Temperature Transmitter
The Rosemount 2240S Multi-input Temperature Transmitter can connect up
to 16 temperature spot sensors and an integrated water level sensor.
Rosemount 2230 Graphical Field Display
The Rosemount 2230 Graphical Field Display presents inventory tank
gauging data such as level, temperature, and pressure. The four softkeys
allow you to navigate through the different menus to provide all tank data,
directly in the field. The Rosemount 2230 supports up to 10 tanks. Up to three
2230 displays can be used on a single tank.
Rosemount 644 Temperature Transmitter
The Rosemount 644 is used with single spot temperature sensors.
Rosemount 3051S Pressure Transmitter
The 3051S series consists of transmitters and flanges suitable for all kinds of
applications, including crude oil tanks, pressurized tanks and tanks with /
without floating roofs.
By using a 3051S Pressure Transmitter near the bottom of the tank as a
complement to a 5900S Radar Level Gauge, the density of the product can be
calculated and presented. One or more pressure transmitters with different
scalings can be used on the same tank to measure vapor and liquid pressure
Rosemount 2180 Field Bus Modem
The Rosemount 2180 field bus modem (FBM) is used for connecting a
TankMaster PC to the TRL2 communication bus. The 2180 is connected to
the PC using either the RS232 or the USB interface.
See the Raptor Technical Description (Document no. 704010en) for more
information on the various devices and options.

Reference Manual
300550EN, Rev AA
December 2010
2-7
Rosemount 2240S
Section 2. Overview
2.4 GETTING STARTED To start up a Raptor system do the following:
1. Install the TankMaster software on the control room PC.
2. Prepare the the start-up by recording the information that will be needed
for configuration of the various devices as described in the Rosemount
Raptor System Configuration manual.
3. Connect the Rosemount 2160 Field Communication Unit to the
TankMaster PC. The 2160 may be connected via a Rosemount 2180
Field Bus Modem, or directly via RS232 or RS485 interface.
4. Connect the Rosemount 2410 Tank Hub to the 2160 Field
Communication Unit.
5. Connect the field devices, such as Rosemount 5900S Radar Level
Gauge and Rosemount 2240S Multi-input Temperature Transmitter, to
the 2410 Tank Hub via the Tankbus.
6. Configure the 2160 Field Communication Unit (if included in the system)
by using the TankMaster WinSetup configuration software.
7. Configure the 2410 Tank Hub by using the TankMaster WinSetup
configuration software.
8. Configure the field devices, such as the 5900S and the 2240S, by using
the TankMaster WinSetup configuration software.
See the Rosemount Raptor System Configuration manual (Document No.
300510EN) for more information on how to configure the various Raptor
devices.

Reference Manual
300550EN, Rev AA
December 2010
Rosemount 2240S
2-8 Section 2. Overview
2.5 INSTALLATION
PROCEDURE
Follow these steps for proper installation of the Rosemount 2240S:
2. Review mounting considerations for the 2240S
(“Installation Considerations” on page 4-2.
5. Power up the 2240S transmitter.
4. Wire the 2240S transmitter
(“Electrical Installation” on page 4-6).
3. Mount the 2240S transmitter
(“Mechanical Installation” on page 4-3).
1. Install the temperature sensor/WLS
(Section 3: MST/WLS Installation).
6. Configure the 2240S transmitter.
(Section 5: Configuration/Operation).

Reference Manual
300550EN, Rev AA
December 2010 Rosemount 2240S
www.rosemount-tg.com
Section 3 MST/WLS Installation
3.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-1
3.2 Installation considerations . . . . . . . . . . . . . . . . . . . page 3-3
3.3 Multiple Spot Temperature Sensor . . . . . . . . . . . . . page 3-4
3.4 Water Level Sensor . . . . . . . . . . . . . . . . . . . . . . . . . page 3-7
3.5 Installing a Temperature Sensor Tube . . . . . . . . . . page 3-8
3.1 SAFETY
MESSAGES
Procedures and instructions in this section may require special precautions to
ensure the safety of the personnel performing the operations. Information that
raises potential safety issues is indicated by a warning symbol ( ). Please
refer to the following safety messages before performing an operation
preceded by this symbol.
Failure to follow safe installation and servicing guidelines could result in death or
serious injury:
Make sure only qualified personnel perform the installation.
Use the equipment only as specified in this manual. Failure to do so may impair the
protection provided by the equipment.
Do not perform any service other than those contained in this manual unless you are
qualified.
To prevent ignition of flammable or combustible atmospheres, disconnect power before
servicing.
Substitution of components may impair Intrinsic Safety.
Explosions could result in death or serious injury:
Verify that the operating environment of the transmitter is consistent with the appropriate
hazardous locations certifications.
Before connecting a handheld communicator in an explosive atmosphere, make sure
the instruments in the loop are installed in accordance with intrinsically safe or
non-incendive field wiring practices.
Do not remove the gauge cover in explosive atmospheres when the circuit is alive.

Reference Manual
300550EN, Rev AA
December 2010
Rosemount 2240S
3-2 Section 3. MST/WLS Installation
High voltage that may be present on leads could cause electrical shock:
Avoid contact with leads and terminals.
Make sure the main power to the Rosemount 2410 is off and the lines to any other
external power sources are disconnected or not powered while wiring the gauge.