Rosen UN7000 Programming manual

ROSEN

UN7000
7” Universal
Headrest
Monitor
Owner’s Manual
and Installation Guide
RosenEntertainmentSystems
1120 CaliforniaAvenue Corona CA92881
[phone]
www.rosenentertainment.com
9000514

UN70007”WidescreenUniversalMonitor Page3
Introduction and System Overview ................................................4
Operating Guide ..............................................................................5
RemoteControl ..................................................................................5
FrontPanelControls ..........................................................................6
Turning On and Off the Monitor ..........................................................7
ChangingVideo Inputs.......................................................................7
DimmingtheBacklight .......................................................................8
Adjusting theColor,Brightness, andTint ............................................8
ImageFormats...................................................................................9
ResetAllSettings .............................................................................10
Installation ......................................................................................11
BoxContents....................................................................................11
ElectricalInstallation ........................................................................12
PhysicalMounting............................................................................13
PedestalMounting ..................................................................................13
FlushMounting .......................................................................................14
Table of Contents
UN70007” Widescreen Universal Monitor Page14
Flush Mounting
The kit includes a protective trim ring and an optional spacer ring for
use when the mounting surface is uneven.
1. Select appropriate locations in your vehicle for the monitor
and for the power supply module.
2. Be sure there is sufficient depth for the trim ring.Add the
spacer ring for shallow locations with uneven curved surfaces
such as upholstery. Be sure there is enough space for both
the trim ring and for any excess interconnect cable.
3. Ensure that the interconnect cable will reach from the monitor
locationto the power supplymodule.
4. Create the required opening for the monitor and trim ring. Be
sure it is not too large, and that there is enough space behind
the trim ring to store any excess interconnect cable. Excess
cable does not fit within the trim ring.
5. Route the cable through the opening in the trim ring:
6. Mount the trim ring with the screws provided.
7. Connect the cable to the monitor.
8. Securely snap the monitor into place.
If you need to remove the monitor from the trim ring, insert the tool
provided between the monitor and the trim ring to release the monitor
from the flexible locking retainer tabs. Gently pull the monitor from the
trim ring. Very gentle pressure can be applied using the tool provided
or a credit card.
Installation
Monitor Trim Ring
Cable
Trim Ring

UN70007” Widescreen Universal Monitor Page4
Introduction and System Overview
Congratulations on your purchase of a Rosen Widescreen Universal
Monitor! This widescreen flat panel LCD monitor features advanced
display technology and versatile installation options.
YourRosenWidescreenUniversal Monitor includesthe following
features:
• 16:9 aspect ratio. Sometimes called “widescreen,” this is the
same aspect ratio used by next generation digital
televisions.
• 7" screen (measured diagonally).
• Adjustable backlight to compensate for ambient lighting
conditions.
• Normal, Zoom, and Full screen formats.
• Front panel and remote controls. These controls allow
adjustment of the video settings, control of the backlighting,
format, and video source. (For more information, see “
RemoteControl” on page 4).
• RCA video inputs.
• RCAauxiliaryvideo output.
Important Notices
• NEVER install this monitor where it can be viewed from the
driving position; this is a violation of many state and local
vehicle codes.
• Use this monitor only after proper installation by a qualified
installer.
• Avoid mounting locations where there is a risk of impact
with a passenger in the event of an accident.
• Always mount the monitor securely using the mounting
hardware that is provided. Do not use the monitor unless it
is properly secured to the vehicle.
• Avoid touching the LCD screen except when cleaning it with a
soft dry cloth.
IntroductionandSystemOverview
UN70007” Widescreen Universal Monitor Page13
PhysicalMounting
Two mountingoptions are available- pedestalmounting or flush
mounting.
Pedestal Mounting
To install the pedestalmount:
1. Select appropriate locations in your vehicle for the pedestal
and for the power supply module.
2. Test fit the mounting pedestal foot in the desired location:
• Be sure that the monitor will be able to slide onto the
pedestalwithoutinterference.
• Besure that themountinglocation can accommodate
screws safely. Never screw into any surface without first
inspecting behind and below it.
3. Ensure that the interconnect cable will reach from the monitor
locationto the power supplymodulelocation.
4. If the mounting surface is not perfectly flat, bend the flanges
on the mounting foot for the best fit without yet removing the
backing from the flange’s double-sided tape.
5. Remove the tape backingand pressthepedestalinto place.
6. Screw the pedestal intoplace withthemountingscrews
provided.
7. Slide the monitor ontothe pedestalas shown,andtightenthe
adjustmentknob.Adjustviewingangle as needed.
Installation

UN70007” Widescreen Universal Monitor Page5
RC-1029A
MOBILE AV REMOTE CONTROL
0
REP
SCAN SAVE
7
4
8
5
MUTE
DISP
BAND
VOL
9
6
MEMORY
CH/DISC/SET
POWER
12
MENU
MODE
Operating Guide
Remote Control
The remote control includes the following buttons for use with this
monitor:Monitor Menu, Mode,Up, Down,and Power.Other buttons
on the remote do not control the monitor.
Power
Up Down
Monitor Menu
Mode
OperatingGuide
UN70007” Widescreen Universal Monitor Page12
ElectricalInstallation
Begin installation of the Widescreen Universal Monitor by installing
the power supply module and routing cables, as shown.
Interconnect Cable
Red:
12V(+) switched (accessory)
Blue:
12V(+) output, 1A capable
Video Out
Video source 2
(Input)
Yellow:
12V(+) constant power (battery)
Four-wire power harness:
Video source 1
(Input)
Power Supply Module
Black:
negative chassis ground
Monitor
RCA connections:
Note: This system is intended for 12-volt negative-ground
systems only.
Note: To avoid damage to the power supply module, never leave
the blue wire bare when unused or when it is shorted to
the chassis ground.
Installation

UN70007” Widescreen Universal Monitor Page6
Front Panel Controls
The front panel controls are located on the lower edge of the monitor.
IR Remote
Receiver Down Up Power/ Mode
Menu
UN7000 7" Monitor
OperatingGuide
UN70007” Widescreen Universal Monitor Page11
Installation
TheWidescreen Universal Monitor includesmounting options
described in the following sections. Before you install the monitor,
consider the following important notices:
• NEVER install this monitor where it can be viewed from the
driving position; this is a violation of many state and local
vehicle codes.
• Avoid mounting locations where there is a risk of impact with
a passenger in the event of an accident.
• Always mount the monitor securely using the mounting
hardware that is provided. Do not use the monitor unless it is
properly secured to the vehicle.
• The Installer accepts all responsibility for the suitability of
thisproduct installation. Rosen Entertainment Systemsis not
liable for any damages, incidental or otherwise, which may
occur from the installation of this product.
Box Contents
The Rosen Widescreen Universal Monitor includes the following
parts and equipment:
• monitor
• remotecontrol
• powersupplymodule
• mountingpedestal
• flush mounting trim ring
• spacer ring for the flush mount trim ring
• monitorinterconnect cable
• four-wire power supply harness
• mountingscrews
• removal key to release the monitor from flush mount trim ring
Installation

UN70007” Widescreen Universal Monitor Page7
Turning On and Off the Monitor
To turn on the monitor:
• Press and release the POWER button on the monitor or the
remotecontrol.
To turn off the monitor:
• Press and hold the POWER button on the monitor or the
remotecontrol.
Changing Video Inputs
The monitor can be used with either NTSC or PAL video signals.
NTSC is the North American video standard and is compatible with
all Rosen video sources.
To change the active video input:
1. Press the POWER button to turn on the monitor.
2. Press MENU on the monitor or MENU on the remote control.
The following screen appears in the monitor.
AV1 : NTSC
MEN
MODE
“AV1” appears briefly whenAV1 is the active input.
“AV2” appears briefly whenAV2 is the active input.
3. Press  or  to toggle between NTSC or PAL.
4. Press POWER on the monitor, or MODE on the remote
control to toggle between “AV1” and “AV2.”
5. Press MENU on the monitor, or MENU on the remote control
again, to exit the menu.
OperatingGuide
UN70007” Widescreen Universal Monitor Page10
ResetAll Settings
TheReset menu optionenables youto restoreallsettings to their
original factory values.
To resetall settings:
1. Press Menu on the monitor or Monitor Menu on the remote
control. The OSD menu appears.
2. Press Menu on the monitor or Monitor Menu on the remote
control until the arrow points to “Reset.”
3. Press  or to return all settings to factory defaults.
4. Press Menu on the monitor or Monitor Menu on the remote
control again to exit the menu. The menu disappears after 5
seconds if no buttons are pressed.
OperatingGuide

UN70007” Widescreen Universal Monitor Page8
Dimming the Backlight
TheWidescreen Universal Monitor featuresan adjustablebacklight
that dims or brightens the monitor to enhance viewing in varying
lighting conditions.
To adjust thebacklight:
1. Press the Menu button on the monitor or Monitor Menu on
the remote control. The OSD menu appears.
COLOR
BRIGHT
TINT
MEN
MODE
FORMAT
RESET
DIMMER
2. Press Menu on the monitor or Monitor Menu on the remote
control until the arrow points to “Dimmer.”
3. Press  or to turn the dimmer on or off.
4. Press Menu on the monitor or Monitor Menu on the remote
control three times to exit the menu. The menu disappears
after 5 seconds if no buttons are pressed.
Adjusting the Color, Brightness, and Tint
If necessary, you can adjust the color, brightness, and tint of the
monitor.
To adjust color, brightness, or tint settings:
1. Press the MENU button on the monitor or Monitor Menu on
theremote control. TheOSD menuappears.
2. Press MENU on the monitor or on the remote control until the
arrow points to “Color,” “Brightness,” or “Tint.”
3. Press the  and buttons to adjust the setting. The setting
will be displayed on the screen, as shown. There are 64 steps
of adjustment. The default setting is 32 on a 64-step scale.
OperatingGuide
UN70007” Widescreen Universal Monitor Page9
COLOR 32
MEN
MODE
4. Press Menu on the monitor or Monitor Menu on the remote
control again to exit the menu. The menu disappears after
5 seconds if no buttons are pressed.
Image Formats
The Widescreen Universal Monitor includes three image formats:
“Normal,” “Full,” and “Zoom.” “Normal” is used in most VHS
applications. “Full” can use the widescreen image produced by
DVDs. In order to use the DVD’s “enhanced for 16:9 television,”
(sometimes known as anamorphic video or widescreen) set the
monitor’s image format to “Full.”
To change the image format:
1. Press Menu on the monitor or Monitor Menu on the remote
control. The OSD menu appears.
2. Press Menu on the monitor or Monitor Menu on the remote
control until the arrow points to “Format.”
3. Press  or to select a format.
4. Press Menu on the monitor or Monitor Menu on the remote
control again to exit the menu. The menu disappears after 5
seconds if no buttons are pressed.
Normal Full Zoom
OperatingGuide