Roverpet KK3 User manual

Roverpet 20 Kiji Dava Circle Prescott, Arizona 86301 800-658-5925 [email protected]
Roverpet #KK3 Cat Climber Assembly Instructions
Roverpet #KK3 Climber Inventory:
(4) #24TLC legs (4) #18TAC arms (4) #34URP short uprights
(4) #46URP long uprights
(10) #17CBC crossbars (17” long)
(10) #23CBC crossbars (23” long)
(10) #250 divider clips
(6) # FDC “custom” wall clips with screws
(5) Sheep skin furry pads
(3) #CSR12 cat scratch rollers
1.) Unpack shipping carton and inspect quantity of components against
inventory list above.
2.) As assembly will be accomplished by first building two separate towers
and then attaching them together, gather the parts needed to assemble
the two-level tower first as follows:
(2) #24TLC legs, (2) #18TAC arms, (4) #34URP short uprights,
(4) #17CBC crossbars, (4) #23CBC crossbars, (2) sheepskin pads
3.) Connect two #24TLC legs together by inserting two #17CBC crossbars
into the holes between them as seen in the photo below.

Roverpet 20 Kiji Dava Circle Prescott, Arizona 86301 800-658-5925 [email protected]
4.) Insert the four #34URP uprights into the upward facing holes of the
#24TLC legs in the following manner: the two pipes identified with red
marks on their tops are to go into the lower left and upper right locations
as viewed with one of the long faces of the assembly positioned in front of
you. Turn the upper-most holes in the uprights to face each other across
the longer faces of the assembly as shown in the left photo below.
5.) Once you have installed the uprights in their correct position, install two of
the #23CBC crossbars into the lowest sets of holes in the uprights to span
across the longer faces of the assembly. See the right photo above.
6.) Install the rings of one sheepskin pad, furry side up, over the uprights and
down onto the crossbars just installed. See the left photo below.
7.) Insert two #17CBC crossbars into the middle set of holes in the uprights to
span across the narrower faces of the assembly. See the right photo
above.
8.) Install two #23CBC crossbars into the uppermost holes in the uprights to
again span across the longer faces of the assembly. See the left photo at
the top of the next page.
Install the uprights with
red marks at their tops at
these two locations and
face the upper-most holes
in the uprights towards
each other across the
longer faces of the
assembly as shown by
the green arrows.

Roverpet 20 Kiji Dava Circle Prescott, Arizona 86301 800-658-5925 [email protected]
9.) Install the rings of the second sheepskin pad, furry side up, over the
uprights and down onto the crossbars just installed. See the right photo
above.
10.) Install the two #18TAC arms into the uprights and fully seat them. See
the photo below.
11.) Set the completed two-level assembly aside.
12.) Connect the remaining #24TLC legs together with two #17CBC
crossbars as you did when putting together the two-level assembly.
13.) Insert the four #46URP uprights into the upward facing holes of the
#24TLC legs in the same manner used to install the uprights in
the two-level assembly already completed. Refer back to step #4 for
clarification.
14.) Install the rings of one sheepskin pad, furry side up, over the uprights
down onto the crossbars just installed. See the photo below.
15.) Install two #23CBC crossbars into the next higher set of holes in the
uprights to span across the longer faces of the assembly as shown in the
photo below.

Roverpet 20 Kiji Dava Circle Prescott, Arizona 86301 800-658-5925 [email protected]
16.) Install two #17CBC crossbars into the next higher set of holes in the
uprights to span across the narrower faces of the assembly as shown in
the left photo below.
17.) Install the rings of one sheepskin pad, furry side up, over the uprights
down onto the crossbars just installed. See the right photo above.
18.) Install two #23CBC crossbars into the next higher set of holes in the
uprights to span across the longer faces of the assembly as shown in the
photo below.
19.) Install the last two remaining #17CBC crossbars into the next highest set
of holes in the uprights to span across the narrower faces of the
assembly. See the left photo below.

Roverpet 20 Kiji Dava Circle Prescott, Arizona 86301 800-658-5925 [email protected]
20.) Install the rings of the last remaining sheepskin pad, furry side up, over
the uprights and down onto the crossbars just installed. See the right
photo above.
21.) Install the last two remaining #23CBC crossbars into the highest set of
holes in the uprights to span across the longest faces of the assembly.
See the left photo below.
22.) Install the two #18TAC arms into the uprights and fully seat them. See
the right photo above.
23.) Set the two completed assemblies side-by-side and connect them
together by attaching the supplied #250 clips along the length of the
center frame pipes. Place five clips on the front and five on the rear of the
assembly. See the photos below.
24.) Attach the six supplied #FDC wall clips to the rear of the assembly as
show in the photos below.
25.) Select a wall location for the Roverpet #KK3 Cat Climber and attach it to
the wall with anchors (not supplied by Roverpet) which are appropriate for the
construction material of the wall. As an example, typical stud and drywall
Attach five
#250 clips
on both the
front and
back of the
assembly at
these
locations.
Attach FDC
wall clips
on backside
of assembly
at these
locations.

Roverpet 20 Kiji Dava Circle Prescott, Arizona 86301 800-658-5925 [email protected]
construction will require hollow wall anchors or toggle bolts. Use the
attached #FDC wall clips as a template to pilot drill for the anchor
locations as shown in the photo below. To reduce the squeaking/friction
caused by product on product place a thin layer of Vaseline on the
connection points.
Congratulations! You are now ready to use your Roverpet 5 Level Cat
Climber #KK3.
Property of Roverpet
WWW.ROVERPET.COM