Roverpet WB3644DSF User manual

Roverpet 20 Kiji Dava Circle Prescott, Arizona 86301 1-800-658-5925 [e-mail]
Page 1 of 3
Roverpet #WB3644DSF –36”high 4x4 Whelping Box Assembly Instructions
Inventory list for The Roverpet #WB3644DSF Whelping Box:
(7) #136 36” high panels (1) #D36 36” high door (2) #F24 2’x4’ floors
(1) #44PR5 5” high puppy rail assembly (two leg bars, two cross-bars and four legs
(1) #44DPK Designer Puppy Keeper (6” high) (4) #180 straight stabilizers (4) #90 corner stabilizers
(12)#250 floor/divider clips
(24)#200 panel clips (pre-assembled onto frames by Roverpet)
Assembly Procedure
1.) Unpack contents of shipping carton and compare to parts list above.
2.) Layout the two #136 panels / #D36 door sub-assemblies as show below, with the assembly containing the
door positioned on the right side.
3.) Connect the ends of the sub-assemblies together with the #200 panel clips that are already attached to the
end panels; reposition panels into a square shape resembling the main photo at the top of this page.
4.) Install #180 straight stabilizers onto the top of in-line connected panels (left photo below) and install #90
corner stabilizers onto the top of corner connected panels (right photo below).
5.) Lay floor trays side-by-side into the bottom of the Roverpet whelping box with the frame pipes facing up to
allow connection to the side panels.
#200 panel clips- pre-attached
to end panels here by Rover
Co.

Roverpet 20 Kiji Dava Circle Prescott, Arizona 86301 1-800-658-5925 [e-mail]
Page 2 of 3
6.) Connect floors to side panels with supplied #250 floor clips in the following manner:
- One in the middle of each bottom bar of the #136 panels.
- Two at the extreme ends of the #D36 door frame bottom bar (do not place in the door opening).
- Three equally spaced across the mid-span of the floor frames.
7.) Assemble the puppy rails by inserting the cross-bars into the through-drilled holes in the main bars and
then insert the four legs into the blind holes drilled into the bottom of the main bars; be sure to orientate the
main bars so that all four blind holes are facing the same direction. Refer to the three photos below for
visual clarification.
8.) Insert the Roverpet puppy rail assembly into the whelping box with the drilled and end-notched leg bars
running across the door opening for correct fastening orientation, as shown in the left photo below; partially
engage the two notched ends of the leg bars with the second inward-most vertical bars of the #136 panels
as shown in the right photo below.
9.) Proceed with lowering the Roverpet puppy rail assembly into the opposite side of the Roverpet whelping
box and completely engage the notched ends of the leg bars with the small vertical bars of the #136
panels. Supporting the small vertical bars with one hand while simultaneously pushing the leg bars towards
the #136 panel with your other hand will help to more easily facilitate the connection. Refer to the two
photos below for visual clarification.
10.) Once fully engaged with the vertical bars of the #136 panels, push the Roverpet puppy rail assembly
completely to the bottom of the Roverpet whelping box and seat it against the floor trays.
11.) Starting on the right side of the #D36 door (looking from the outside of the whelping box),feed the #DPK
Designer Puppy Keeper, with the label side facing out, between the large outer pipe of the door frame and
the small diameter vertical bar adjacent to it (left photo below). Feed the fabric across the back of the door
and pull it back through the same position on the other side of the door (right photo below).

Roverpet 20 Kiji Dava Circle Prescott, Arizona 86301 1-800-658-5925 [e-mail]
Page 3 of 3
12.)Return the end of the fabric back inside the Roverpet whelping box by routing it around the outer frame
pipes of the #D36 door and the #136 panel connected to it (left photo at the top of the next page). Run the
fabric down the inside of the panel and pull it back outside of the whelping box between the 2nd and 3rd
small diameter vertical bars from the corner (right photo at the top of the next page).
13.)Feed the fabric back between the 1st and 2nd small vertical bars (left photo below), around the back of the
first pipe and back out to the front of the whelping box between the first vertical pipe and the outer frame
pipe (right photo below). Wrap the fabric around both frame pipes that make up the corner and feed the
end back inside the Roverpet whelping box again between the corner pipes and the first small vertical bar
of the adjacent #136 panel (again see right photo below).
14.)Run the fabric along the inside of the Roverpet whelping box until you reach the center where the two #136
panels connect and feed the fabric out around the frame pipes and back into the whelping box and shown
in the left photo below. Run the fabric along the inside of the Roverpet whelping box to the next corner and
route the fabric around the corner in the same manner as the previous corner and as shown in the right
photo below.
15.)Continue with this method until the two ends of the fabric meet each other and fasten the Velcro straps.
When properly installed, the fabric of the Designer Puppy Keeper will route through the interior of the
Roverpet whelping box as shown below.
16.) Thank You for Purchasing a Roverpet Whelping Box #WB3644DSF
Note: Pig Rails can reduce the risk of possible suffocation. Note: Puppies must be watched at all times.
www.roverpet.com Property of Roverpet