Royal Sovereign RBC-1515-ADBK User manual
B CONTE T CONTEET ETECTON
O
S
Please read and retain these instructions.
To register your product, please go to www.royalsovereign.com
11
CONTENTS
11
1
11
1
SETY NSTCTONS
1.
2.
3.
4.
5.
.
.
.
1.
2.
3.
4.
5.
6.
1.
This product may contain a chemical known to the State of California to cause cancer, birth defects, or
other reproductive harm.
OCT E
BOX CONTENTS
1
T
C STT E
A
B
C
C
C
C
C
CONTO NE
Attach power cable to back of machine, plug into a three prong outlet, and turn power switch on.
-The unit will conduct an automatic self-diagnostic test to ensure accurate counts.
-After five seconds of the counting wheels spinning, the screen will display a "0".
-If there is a problem, the preset display will show an error code. (See ERROR CODE DISPLAYS -
LOCATED ON PAGE 11.)
Select bill counting settings: Before counting, select counting settings that are related to your counting
needs:
-ADD mode:
To continuously add totals for a cumulative total when counting, press the "ADD" button on the control
panel (#1 on the keypad). To turn off this function, press the "ADD" button.
-BATCH mode:
The machine is preset to common counting mode, which automatically counts all bills placed into the
hopper. To count bills in predetermined batches, press the "BATCH" button. To clear the batchfunction
and return to original bill counting, press the "CLEAR" button. (NOTE: Maximum batch speed is1,200
bills per minute).
•Press once for batch quantity of 100
•Press twice for batch quantity of 50
•Press three times for batch quantity of 20
•Press four times to cancel all batching
•'97831&%8',13()- SIPIGXthe "BATCH" button, and use the numeric keypad to entera
batchnumber between and
6
PRODUCT OPERATION
Under the batch counting mode, once the hopper is loaded, the machine will start counting and will
stop when the counted quantity reaches the preset batch quantity. To repeat the batch counting
operation under the same preset batch quantity, simply remove the counted banknotes from the
stacker. The machine will batch the next group of banknotes under the same settings. If you wish to
keep batching without removing the banknotes from the stacker, press the “START” button.
-Counting Speeds
Press the "SPEED" button on control panel and continue to press the key until you come to speed
setting you wish to use (900, 1,200, 1,500).
-Counterfeit Detection Methods
All methods are automatically on when the unit is powered up. To manually turn off any or all methods
see (CONTROL PANEL - LOCATED ON PAGE 5.)
-AUTO or MANUAL Start
The machine is preset to automatically start counting bills once placed into the hopper. To change to
the manual start mode, press the "MNL" button (#2 on the numeric keypad). MNL will appear on the
display. Insert the bills into the hopper, and press the "START" button. Press the "MNL" button to
switch back to Auto mode.
7
PRODUCT OPERATION (CONTINUED)
3. Place bills into the hopper to begin counting; press "START" if in manual mode
NTENNCE O TE CNE
NN
CC
1
CTON O NOT CNE TE OSTON O TE ETECTOS NO OTC SENSOS
SECCTONS
Model RBC-1515-ADBK
Power single-phase 100~240V 50/60Hz (±10%)
Power Consumption 80W (Max)
Surroundings Temperature of Usage 0~40°C
Hopper Capacity / Stacker Capacity 500 notes / 200 notes
Counting Speed 900 / 1,200 / 1,500 bills per minute
Accepted Note Size L:50~110mm (1.9 - 4.3 in) W:90~190mm (3.5-7.5 in)
Display Range Counting: 3 Digits / Batch Counting: 3 Digits
Dimensions 265 × 250 × 220 mm (10.4 x 9.8 x 8.7 in)
Net Weight 12.8 lbs. / 5.8kg
9
TROUBLESHOOTING
Problem Reason Solution
Bills get damaged
Machine runs slow
Hopper
Tension is
too tight
To loosen the tension, please turn the bill thickness adjuster (located on the top
of the machine) one notch to the right (+). Repeat bill counting and adjust if
problem continues.
Bills eject from the
machine
Display shows
miscount
Hopper
Tension is
too loose
To tighten the tension, please turn the bill thickness adjuster (located on the top
of the machine) one notch to the left (-). Repeat bill counting and adjust if
problem continues.
Counterfeit bills are
being added to the
total count
Setting
needs to be
modified
Press the “BATCH” and “DD” buttons together for 1.5 seconds. The display will
show two codes. Then press the "DD" button to display the code -C02, next press
the button “+” or “-” to make the above code be “1” or “0”. (0 means exclude the
counterfeit while 1 means include the counterfeit). Finally put your finger on the
hopper sensor to save the setting.
UV error code is
occurring in
abundance
Setting
needs to be
modified
Press “SET” button for about 2 seconds, the display will show “EC0”, continue to
press “SET” button until display shows “E10”.
The UV sensitivity will be high if parameter is low.
Software default UV setting is 150.
IR error code is
occurring in
abundance
Setting
needs to be
modified
Press “SET” button for about 2 seconds, the display will show “EC0”. Then press
“+” or “-“ to increase or decrease the parameter.
The IR sensitivity will be low while parameter is low.
The IR sensitivity will be high if parameter is high.
Software default IR setting is 30.
MG error code is
occurring in
abundance
Setting
needs to be
modified
Press “SET” button for about 2 seconds, the display will show “EC0”, continue to
press “SET” button until display shows “E72”.
Then press “+” or “-“ to increase or decrease the parameter.
The MG sensitivity will be low while parameter is low.
The MG sensitivity will be high if parameter is high.
Software default MG setting is 12.
DD error code is
occurring in
abundance
Setting
needs to be
modified
Press “SET” button for about 2seconds, the displaywill show “EC0” ,continue to
press the “SET” button until the display will show “E82”.
The DDsensitivity will be high while parameter is low.
The DDsensitivity will be low if parameter is high.
Software default DD setting is4.
ERROR CODE DISPLAY AND SOLUTIONS
The display may show some error code in counting, which means there are some problems with the machine. Refer
to the chart below to solve the error.
Most of the errors listed above may be caused by dust or dirt on the inside of the machine. Keeping the machine
clean is highly recommended (Please refer to MAINTENANCE OF THE MACHINE - LOCATED ON PAGE 8).
10
Error Code Reason
EC0 Double-notes. Put the notes from the stacker onto the hopper again, press START to count
again. If EC0 often appears, please adjust the position of the bill thickness adjuster
E10 UV fake notes or questionable notes. Eliminate this note, press START and count
continuously.
E6X/E7X MG fake notes or questionable notes. Eliminate this note, press START and count
continuously.
E8X Joined notes. Put the notes from the stacker onto the hopper again, press START to count
again.
E4X Half-notes. Put the notes from the stacker onto the hopper again, press START to count again.
E82 Different width or different version notes. Press START and count continuously.
CE1 UV sensor
CE2 Width sensor or big motor
CE3 Left counting sensor
CE4 Right counting sensor
CE5 Feeding sensor
CE6 MG sensor
CE7 MG sensor
CE8 Stacker sensor
ONE YE TE NTY
S
1
S
S
OY SOEEN NTENTON NC
11
11
Table of contents
Other Royal Sovereign Cash Counter manuals
Royal Sovereign
Royal Sovereign RBC-3200-CA User manual
Royal Sovereign
Royal Sovereign RBC-650PRO User manual
Royal Sovereign
Royal Sovereign RBC-4500 User manual
Royal Sovereign
Royal Sovereign RBC-ES240-CA User manual
Royal Sovereign
Royal Sovereign RBC-100P User manual
Royal Sovereign
Royal Sovereign RCD-UVP2 User manual
Royal Sovereign
Royal Sovereign RBC-5000 User manual
Royal Sovereign
Royal Sovereign RBC-2200-CA User manual
Royal Sovereign
Royal Sovereign RBC-1003 User manual
Royal Sovereign
Royal Sovereign RBC-1003 User manual
Royal Sovereign
Royal Sovereign RBC-ES200 User manual
Royal Sovereign
Royal Sovereign RBC-EP1000-CA User manual
Royal Sovereign
Royal Sovereign RBC-5000 User manual
Royal Sovereign
Royal Sovereign Fast Sort FS-2D User manual
Royal Sovereign
Royal Sovereign RBC-ED350 User manual
Royal Sovereign
Royal Sovereign RBC-ED200 User manual
Royal Sovereign
Royal Sovereign RBC-660 User manual
Royal Sovereign
Royal Sovereign FS-550D User manual
Royal Sovereign
Royal Sovereign RBC-1000 Series User manual
Royal Sovereign
Royal Sovereign RBC-1002 User manual
Popular Cash Counter manuals by other brands
KISAN
KISAN NEWTON K5 quick start guide
TSUJI ELECTRONICS
TSUJI ELECTRONICS CT08-ER2 user manual
TSI Instruments
TSI Instruments AeroTrak 8220 Service manual
HYDAC International
HYDAC International ALPC 9000 Series Operating and maintenance instructions
Keysight Technologies
Keysight Technologies 53210A Service guide
Omron
Omron SYSMAC C200H-CT001-V1 Operation manual
