Royal Sovereign ES-400C User manual

LAMINATOR MODEL NO. ES-400C
OWNER'S MANUAL
Royal Sovereign International Inc.
Read all instructions carefully before use.
For any customer support needs, please choose the
« Customer Support » tab on www.royalsovereign.com

MAJOR PARTS 3
CHARACTERISTICS OF ES SERIES 3
SAFETY PRECAUTIONS 4
HOT LAMINATING PROCEDURE 5
COLD LAMINATING PROCEDURE 6
SPECIFICATIONS 7
TABLE OF CONTENTS
ES-400C
TOPIC PAGE

ES-400C
MAJOR PARTS
CHARACTERISTICS OF ES SERIES
FRONT OPENING
BASE
READY INDICATOR LIGHT
COVER
POWER SWITCH
3
1. The ES Series has been designed and manufactured to provide lamination for
all of your school, home and office needs.
2. Easy operation.
3. The ES-400C offers a cold lamination feature that will protect your heat
sensitive material.
4. The ES-Series is designed with a stylish rounded design
that complements any environment.

SAFETY PRECAUTIONS
The safety recommendations outlined in this section are to be read
and followed before operating this machine. Keep this information for
future reference.
1. To prevent the possibility of a fire or injury,do not allow foreign
articles(neckties, scarves, or parerclips) inside the machine.
2. Do not attempt to laminate items that exceed total
recommended material thickness.
3. Do not insert pouch film with the back end first.
(Front of film: sealed side,Back of film unsealed side.)
This may cause the pouch to jam the rollers.
4. To prevent the possibility of electric shock, do not immerse
the laminator in water or permit liquids inside the machine.
5. Because the laminator creates heat, keep out of reach of
children.
6. Do not cut pouch before inserting into laminator.
(This will cause the laminator to jam.)
7. Do not laminate leaves, flowers, clothes etc.
4
ES-400C

8. If the room temperature is low(under 64f), The ready light
may take longer to come on.
9. Plug the laminator in after verifying the correct voltage.
Failure to comply with the above information could result in
serious injury.
HOT LAMINATING PROCEDURE
5
1. Turn the power switch to the hot position.
The power indicator will light. Allow approximately 10 minutes to preheat.
When the proper temperature is reached, the "ready" light will go on.
2. Place the item to be laminated into the laminating pouch.
3. Insert the pouch film into the front opening of your laminator.
Be sure to center the laminating pouch as it is inserted.
4. The item will autormatically feed out through the rear of the
laminator.
(SAFETYNOTE: The laminated item may be too hot to touch.)
5. If the item is not completely laminated, repeat steps 3-5.
NOTE: Your finished laminated item will be hot,and will easily bend.
To keep your laminated item flat , place on flat surface and allow to cool.
ES-400C

COLD LAMINATING PROCEDURE
1. Turn the power switch to the cold position (" ="). The
power indicator light will not light, but the machine is
now ready to laminate in the cold mode.
2. Place the document to be laminated on the adhesive
side of the cold film with the document face down.
3. Insert the document to be laminated into the front
opening of the machine.
4. Remove paper liner from the cold film slowly while the
document is being inserted into the machine.
6
NOTE: When switching the machine from the hot to cold mode, it will
take approximately 30 minutes for the ready indicator light to turn off.
Please wait for the light to turn off before inserting your document.
ES-400C

SPECIFICATION
7
DESCRIPTION ES-400C
Dimensions 8.3x5.1x3.3 (inch)
210x130x85(mm)
Max. Laminating Width 4.3 (inch) 110 (mm)
Max. Laminating thickness 27.6 (mil) 0.7 (mm)
Film Thickness 75~125(micron), 3~5 (mil)
Number of rollers 2
Cold Function YES
Heater Source Hot shoe
Read Time 10 (min)
Motor Type AC motor
Laminating Speed 6.5 (inch/min)
165 (mm/min)
Weight 2.05 (lbs) 0.93 (kg)
Voltage/Cycle AC 100V~120V(50/60Hz)
AC 220V~240V(50/60Hz)
Power Consumption 100 W
ES-400C

www.royalsovereign.com
RS Holland B.V.
Industrieweg 6K 4104AR Culemborg, The Netherlands.
TEL : [phone]
FAX : [phone]
E-mail : [email protected]
RS International Australia PTY. LTD.
30 Prime Drive, Seven Hills, NSW 2147, Australia
TEL : [phone]
FAX : [phone]
E-mail : [email protected]
CORPORATE HEADQUARTERS
Royal Sovereign International Inc.
2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.
TEL : [phone] FAX : [phone]
E-mail : [email protected]
Royal Sovereign Inc. <Oversea Sales Office>
1001, World Meridian II, 426-5, Gasan-dong,
Geumcheon-gu, Seoul, 153-759, KOREA
TEL : [phone] FAX : [phone]
E-mail : [email protected]
RS Canada Inc.
164 Oakdale Road, Toronto, Ontario M3N 2S5
CANADA
TEL : [phone] FAX : [phone]
E-mail : [email protected]

PLASTIFIEUSE Mod粛e No. ES-400C
GUIDE D'UTILISATION
Royal Sovereign International Inc.
French
Lire attentivement toutes les instructions avant l’utilisation.
Pour tout besoin de service après vente, cliquez sur l'onglet
« Customer Support » sur notre site www.royalsovereign.com

PARTIES PRINCIPALES 11
CARACTÉRISTIQUES DE LA SÉRIE ES 11
PRÉCAUTIONS DE SÉCURITÉ 12
PROCÉDURE DE PLASTIFICATION À CHAUD 13
PROCÉDURE DE PLASTIFICATION À FROID 14
FICHES TECHNIQUES 15
TABLE DES MATIÈRES
SUJET PAGE
ES-400C