Royal Sovereign RSC-LS series User manual

RSC-LS/LSH/CW/HW SERIES Laminators
OWNER'S MANUAL
Royal Sovereign International Inc.
www.royalsovereign.com
Read all instructions carefully before use.
For any Customer Support needs please choose the
Customer Support tab on www.royalsovereign.com

2
TABLE OF CONTENTS
TOPIC PAGE
1. Introduction ........................................................................................................ 3
2. Safety Precautions.............................................................................................. 3
3. Installation ........................................................................................................... 4
4. Included with Laminator...................................................................................... 5
5. Product Identification ........................................................................................... 6
6. Control Panel ...................................................................................................... 7
7. Roller Nip Settings .............................................................................................. 8
8. Using Foot Pedal and Remote Control............................................................... 8
9. Using Cross Cutter ............................................................................................. 9
10. Loading Film...................................................................................................... 9
11. Threading Film
11.1. Decaling ............................................................................................ 10-11
11.2. Mounting ................................................................................................ 12
12. Installation of the Front Feed and Rear Rewind Options ............................... 13
13. Maintenance ................................................................................................... 14
14. Troubleshooting .............................................................................................. 14
15. Specifications.................................................................................................. 15
16. Warranty.......................................................................................................... 16

RSC-LS/LSH/CW/HW SERIES
3
1. INTRODUCTION
2. SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could result in serious injury.
Please read the instructions carefully and keep for future reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. Keep hands and clothing (i.e. Neckties) away from rollers. The rollers have pinch points
that can trap body parts or clothing and cause serious injury.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/
or repairing.
8. Keep out of reach of children.
9. Only Royal Sovereign authorized maintenance and service technicians should make
repairs.
10. Do not attempt to laminate items that exceed total recommended material thickness
for the unit
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when they are hot or place foreign objects inside the machine.
13. Do not cover the surface of the machine until the machine has completely cooled.
14. If emergency happen, press emergency switch immediately.
15. Temperature of circumstance: 20°C ± 5°C; humidity of circumstance: < 95%(20°C ± 5°C).
16. Warning - Hazardous Moving Parts – Keep Fingers And Other Body Parts
Away.
Thank you for choosing a Royal Sovereign laminator. It has been designed and
manufactured to provide years of continuous service. For complete operating and
maintenance information please read this manual thoroughly. Upon receipt of your
laminator, please inspect the box, the machine and all other contents for shipping
damage. Damage should be brought to the immediate attention of the delivering carrier
(See page 5 for list of shipment elements).

4
3. INSTALLATION
Note: The laminator should be installed by a trained service technician.
ELECTRICAL REQUIREMENTS
The laminator comes fully assembled, except for the feed table and paper guide to avoid
shipping damage. Upon arrival, thoroughly inspect the unit. It is imperative that any
shipping damage is reported and a claim is filed with the delivering carrier immediately
upon receipt.
The laminator should be located in an area with adequate work space for feeding graphics
and lamination materials.
Avoid placing the laminator in a dusty area or near sources of extreme heat or cold.
Once the laminator is in place, lock the casters into position(“ON” position). Always
unlock the casters (“OFF” position) when moving to a different location.
Royal Sovereign recommends that a licensed electrician ensures proper power installation
to your laminator in accordance with electrical codes in your area.
The laminator should have a dedicated power line.
230V UL
120V UL
220V EU
240V UK
220V AU

RSC-LS/LSH/CW/HW SERIES
5
4. INCLUDED WITH LAMINATOR
Thoroughly inspect the parts and the unit. It is imperative that any missing parts are
reported and a claim is filed with the reseller immediately upon receipt of shipment.
Part Name
Laminator
Owner's Manual
3´´(76mm) / 2" (57mm) Auto Grip
3´´ (76mm) Auto Grip(America. Canada.Mexico)
Dust Cover
Spare Motor Fuse - FUSE(50T)
(6.3A)
Spare Main Power Fuse - FUSE(65TS)
5A(RSC-LS/C SERIES)/15A(RSC-LSH/H SERIES)
1/4"Hexa head Bolt (M6 * 20mm)
Spring Washer(¢6.1)
(Included with option only)
3/16"screw (M5 * 12mm).
Spring Washer(¢5.1)
(Included with option only)
Front Feeder and Rear Rewinder Kit
(Included with option only))
1
1
6/6
6
1
1/1
1
1
1
8/8
8/8
12/12
12/12
2/2
Quantity Picture
L-wrench 2.5/6 (Stand Separate )
L-wrench 2.5 ( Stand Assemble ) or

6
5. PRODUCT IDENTIFICATION
8
9
1
2
11
3
4
13
7
14
6
12
5
10
NO PART NAME
1 EMERGENCY SWITCH O
2 FEED TABLE O
3 MAIN ROLLER O
4 ASSEMBLY STAND O
5 FOOT PEDAL O
6 TENSION CONTROL KNOBS O
7 PRESSURE LEVER O
8 CONTROL PANEL O
9 UPPER IDLE BAR O
10 RELEASE LINER TAKE UP O
11
LASER SYSTEM FOR SAFETY O
12 REMOTE CONTROL O
13 FILM SUPPORT Except US, CA
14 REAR-REWINDER
Option (RSC-LS/LSH)
Standard (RSC-CW/HW)

RSC-LS/LSH/CW/HW SERIES
7
6. CONTROL PANEL
When the machine is initially turned on, the LED display window will show the speed set
at 1.
Control Buttons
1. SPEED DISPLAY: Display’s current Speed.
2. SPEED BUTTON: Adjusting the speed of the rollers. To change the speed of the rollers, press the
up or down arrow button.
3. HEAT BUTTON : To select HEAT(122℉,50℃) or COLD mode.
4. REV: To reverse the rollers, press and hold the REV button.
5. RUN: To start the rollers.
6. STOP: To stop the rollers.
11
22
3
4
4
65
56
RSC-LSH/HW SERIES RSC-LS/CW SERIES

8
7. ROLLER NIP SETTING
25mm
1 in
1mm
0.04 in
Laminating
5-7mm
0.2-0.28 in
Open
20 -23mm
0.8-0.9 in
15-18mm
0.6-0.7 in
10-13mm
0.4-0.5 in
It is important to adjust the roller nip settings to the appropriate thickness of the board
being used. Use the guide below to adjust to the correct position.
8. USING FOOT PEDAL AND REMOTE CONTROL
USING FOOT PEDAL
USING REMOTE CONTROL
Place the foot pedal on the floor in front of the
machine. Once all correct settings are displayed, you
may use the foot pedal to operate the laminator for
“Hands Free Operation.” To activate the machine,
press the foot pedal once and then release. Repeat to
stop the rollers.
Located on the rear left side of the laminator.
1. PRESS REV – To reverse the rollers. Press and
hold the button (useful for jams or misted media).
2. PRESS STOP – To stop the rollers from turning.
3. PRESS FWD – To activate the rollers.
If you don't want to laminate,
please place the pressure leverto the
"Open position(NO.7)".
1
2
3
4
5
6
7
NO Inches Metric
(mm)
1 Lamination Lamination
2 1/25˝1
3 3/6˝~1/4˝5~7
4 3/8˝~1/2˝10~13
5 3/5˝~18/25˝15~18
6 4/5˝~3/25˝20~23
7 1˝25
2
1
3

RSC-LS/LSH/CW/HW SERIES
9
9. USING CROSS CUTTER
Figure 1 Figure 2 Figure 3
The cross cutter is located on the rear exit table of the machine.
1. After lamination, move the cutter approximately to the center of the completed
application at the desired point of detachment (Figure 1).
2. Grasp film with one hand, press the cutter downward into the application and slide it first
to one end of the application, then to the other end to complete the cut (Figure 2 & 3).
10. LOADING FILM
Royal Sovereign films are wound with the adhesive side facing the inside of the roll (adhesive in).
Loading films to upper and lower film shafts:
(See page 5 for assistance with parts identification.)
1. Adjust the auto grip to fit to the film and tighten the
auto grip screw (Figure 1).
2. Remove the upper and lower film shafts from the
machine and load the films (Center the upper and
lower films on the shaft). Note the direction of the
adhesives on the lower and upper films
(Figure 2).
3. Load the upper and lower film shafts on the
machine (Figure 3).
Figure 1
Figure 2
Figure 3

10
11. THREADING FILM
Figure 1
Figure 2
11.1. Decaling
1. Turn the power switch on (“I” position). The Power
switch is located on the rear left side of the unit.
2. Complete the steps as in the “LOADING FILM”
section (see page 10).
3. Set the top roller to the desired temperature .
4. Take off the Frame-Paper Guide and the Feed Table.
5. Pull the top film down over the Safety Cover to the
bottom of the craft paper/mounting film.
6. Align and center the craft paper/mounting film to the
top film and tighten the two lower core screws (Figure
1).
7. Thread the top film underneath the Upper Idle Bar.
(Figure 2)
8. Tape the top film on to the Release Liner Take-Up.
(Figure 2)
TAKE UP DEVICE
PAPER BACK
HOT ROLLER
BACKING PAPER
BASE FILM
LOEWER IDLE BAR
UPPER IDLE BAR
COLD FILM