Royal Sovereign ES-1310 User manual

Royal Sovereign International, Inc.
ES-910/1310
LAMINATOR
Owner's Manual
Please read and retain these instructions.
To register your product, please go to www.royalsovereign.com USA.
Click the Customer Support Tab then Registration Tab.
www.royalsovereign.com
Página en Español 9
Page en Français 17

LAMINATOR

ES-910/1310
3
SAFETY INSTRUCTIONS
The safety recommendations outlined in this section should be read and understood before operating this machine. When
using this machine follow these basic safety precautions to reduce risk of fire, electric shock or injury. Keep this information for
future reference.
1. To prevent the possibility of a fire or injury, do not allow foreign articles inside the machine.
2. Do not attempt to laminate items that exceed total recommended material thickness.
3. Do not insert pouch film with the back end first. (Front of film: sealed side, Back of film: open side.) This may cause the
pouch to jam the rollers.
4. To prevent the possibility of electric shock, do not immerse the laminator in water or permit liquids inside the machine.
5. Because the laminator creates heat, keep out of the reach of children.
6. Do not cut pouches before inserting them into the laminator. This will cause the laminator to jam.
7. Do not laminate leaves, flower, clothes etc.
8. If the room temperature is low (under 64˚F), the ready light may take longer to come on.
9. When unplugging the power plug, grip the plug to pull it out. Pulling the cord may result in electric shock, fire, or
damage to the machine.
10. Do not use the machine if the cord is damaged. This may result in electric shock, fire, or other hazards.
11. Do not place objects on the power cord and do not bend it excessively. This may result in electric shock, fire or other
hazards.
12. When not using the machine for long periods of time, unplug the power cord from the outlet.

4
Box Contents 5
Parts 5
Controls 5
Features 5
Operation 6
Troubleshooting 7
Specifications 7
Warranty 8
Contact Information 8
Página en Español 9
Page en Français 17
CONTENTS

ES-910/1310
5
BOX CONTENTS
Laminator and pouch film
PARTS
CONTROLS
FEATURES
Hot and Cold Lamination
The laminator can easily be adjusted to handle both hot and cold lamination pouch film.
Temperature Control
Individual settings for different film thicknesses from 3-5 mil.
Ready Light
A green ready light clearly indicates when the machine has reached optimal temperature and is ready to laminate.
Fast speed
Laminates up to 14.2” per minute.
Automatic Shut-Off Function
The machine will automatically shut off after one hour of non-use.
Control Panel
Front opening
Cold lamination setting
3 mil film setting
5 mil film setting
Power button
Setting control
Reverse switch
Adjustable cooling guides

6
OPERATION
Hot Lamination
1. Place the machine on a flat, sturdy surface and press the power button to turn on the machine.
2. Pull out the cooling guides.
3. The machine is preset to the 3mil setting. To change the setting press the setting control button. The machine will take
approximately 5 minutes to warm-up. When the proper temperature is reached, the ready light will glow steady.
4. Place the item to be laminated into the laminating pouch.
5. Insert the pouch film into the front opening of the laminator. Make sure to place the sealed end of the pouch film in first.
6. The document or photo will then automatically feed out the through the back of the machine.
NOTE: Laminated items exiting the machine may be too hot to touch.
7. If the item is not completely laminated, repeat steps 4-5.
NOTE: Laminated items will be hot and will easily bend. To keep the item flat, place on a flat surface and allow it to cool
or lay item on the cooling guides.
Before laminating important or unique documents,
always test a pouch through the laminator using a similar document.
Cold Lamination
1. Place the machine on a flat, sturdy surface and press the power button to turn on the machine.
2. Press the setting control button until the Cold lamination setting is lit. If the machine was previously used in hot
mode, allow approximately 25 minutes to cool down. When the proper temperature is reached, the ready light will
glow steady.
3. Place the document to be laminated on the adhesive side of the cold film with the document face down, sealed end first.
4. Insert the document to be laminated into the front opening of the machine.
5. Remove paper liner from the cold film slowly while the document is being inserted into the machine.

ES-910/1310
7
Symptom Solution
Motor does not work. Check to make sure machine is plugged in. Check to make sure the power
button is turned on.
Pouches are not laminating correctly. Make sure that the machine is set to the correct hot setting.
The pouch is jammed. Press down the reverse switch and the pouch will exit the front of the machine.
TROUBLESHOOTING
If you are still having complications, please contact Royal Sovereign’s Service Center at 1-800-397-1025.
SPECIFICATIONS
Model ES-910 ES-1310
Dimensions 19.2x6.6x4.7 (inch)
490x167x120 (mm)
Maximum laminating width 9.1 " / 230 mm 12.6 "/ 320 mm
Maximum laminating thickness
Film thickness
27.6 mil / 0.7 mm
3~5 mi / 75~125 micron
Number of rollers 2
Cold mode Yes
Heating system Hot shoe
Ready time 4-6 (min)
Motor type AC motor
Laminating speed 14.2" per min. / 360 mm per min.
Weight 6 lbs / 3 kg 7.4 lbs / 3.7 kg
Voltage/Cycle 120V ,60Hz
Power consumption 300 W 400 W
14.6x6.6x4.7 (inch)
370x167x120 (mm)

8
LIMITED ONE YEAR WARRANTY
This warranty applies to repair or replacement of product found to be defective in material or workmanship for one year from
the date of the original purchase. This warranty is extended only to the original purchaser.
This warranty does not apply to damage resulting from abuse, misuse, or improper maintenance of damage that is
attributable to acts of nature. Royal Sovereign International, Inc. (and its affiliated companies) is not liable for incidental or
consequential damages of any nature. This limitation would not apply if you live in those areas that do not permit the
exclusion or limitation of incidental or consequential damages.
Defective products for warranty repair or replacement cannot be returned without a Return Authorization number. Please go
to www.royalsovereign.com USA-Customer Support Tab to make a request for an Office Product Return Authorization.
Defective products must be returned to Royal Sovereign International Consumer Return Department, freight prepaid, with
proof of purchase and Return Shipping and Handling payment (check or money order). Upon repair or replacement the
product will be returned to the customer.
Return defective product to the following address with a detailed description of the problem. If possible, pack in original
carton. Please prepay shipping charges.
For out of warranty service or frequently asked questions please go to www.royalsovereign.com USA- Customer Support Tab.
For sales of product, parts or accessories please visit us at www.royalfulfillmentcorp.com.
For service or sales please contact your local Royal Sovereign Office:
ROYAL SOVEREIGN INTERNATIONAL, INC. RS CANADA INC.
2 Volvo Drive Rockleigh, NJ 07647 USA 1025 Westport crescent, Mississauga, Ontario, Canada L5T1E8
TEL : [phone] FAX : [phone] TEL : [phone] FAX : [phone]
www.royalsovereign.com

ES-910/1310
9
Royal Sovereign International, Inc.
Español
ES-910/1310
LAMINADORA
Por favor lea y conserve estas instrucciones.
Para registrar su producto, visite el sitio web www.royalsovereign.com USA.
Haga clic en la pestaña de “Customer Support” y después en la pestaña de “Registration”.
www.royalsovereign.com
Página en Español 9
Page en Français 17
Manual del Propietario

10
LAMINADORA