RS PRO 122-9143 Installation and operating instructions

RS Components Ltd., Birchington Road, Corby, Northants, NN17 9RS, UK
RS-122-9143 Page 1 of 2 © 2016 Vermason
Made in the
United States of America
Portable Wrist Strap Tester
Installation, Operation and Maintenance
Description
Per EN 61340-5-1, test equipment is required to enact the
Compliance Verification Plan Requirement. Wrist Straps
are to be tested while worn per EN 61340-5-1 Clause A.1.
Test equipment shall be selected to make measurements of
appropriate properties of the technical requirements that are
incorporated into the ESD program plan. The Wrist Strap
Tester can be used to fulfill ANSI/ESD S1.1, “The wrist strap
system should be tested daily to ensure proper electrical
value” (Annex A3). Being a portable battery powered tool,
it is perfect for small labs or for a supervisor to spotcheck
workers and/or ensure compliance.
The Portable Wrist Strap Tester is a battery operated “on
demand” wrist strap tester. When the wearer of a wrist strap
plugs in their coiled cord and pushes the metallic electrode
of the Portable Wrist Strap Tester, a path for current flow is
completed from the wearer’s skin, through the wrist strap.
This action will cause the green “test good” LED to illuminate
as long as the resistance of the circuit path is between 750
kilohms and 35 megohms. This meets the required limits
of ANSI/ESD S20.20 and ANSI/ESD S1.1 tested per ESD
TR53.
Packaging
1 Wrist Strap Tester
1 9V Alkaline Battery
1 Hook and Loop Fastener Strip
1 Certificate of Calibration
July 2016
Figure 1. RS 122-9143 Portable Wrist Strap Tester
Installation
Open the Wrist Strap Tester’s battery compartment and
install the included 9V battery. If desired, use the included
hook and loop fastener strip to mount the tester to a wall or
worksurface.
NOTE: The low battery indicator flashes briefly every time
the unit is used. Replace the battery once the indicator
becomes constant during testing.
Operation
1. Fit the wristband snugly onto your wrist.
2. Snap the coiled cord to the wristband.
3. Plug the coiled cord into the Portable Wrist Strap
Tester’s banana jack.
4. Push and hold the test button until the test results are
displayed.
5. An audible alarm will sound if the test fails. Verify
that your wrist strap is being worn correctly or needs
to be replaced. If your test result fails high, try applying
an approved dissipative hand lotion such as Reztore™
ESD Hand Lotion to your wrist.
Figure 2. Using the Portable Wrist Strap Tester and
recording results
TECHNICAL BULLETIN RS-122-9143

RS Components Ltd., Birchington Road, Corby, Northants, NN17 9RS, UK
RS-122-9143 Page 2 of 2 © 2016 Vermason
Calibration
The RS Portable Wrist Strap Tester is calibrated to NIST
traceable standards. There are no user adjustments
necessary. We recommend that calibration be performed
annually using the RS 685-8757 Calibration Unit. It is a
convenient product which allows the customer to perform
NIST traceable calibration on single-wire personnel testers.
The 685-8757 is designed to be used on the shop floor at
the workstation, virtually eliminating downtime, verifying that
the tester is operating within tolerances.
View technical bulletin PPE-5034.E for more information on
the 685-8757 Calibration Unit and instructions to calibrate
the Portable Wrist Strap Tester.
Figure 3. RS 685-8757 Tester Calibration Unit
Specifications
Power Supply 9V Alkaline Battery
Operating Temperature 0 to 40°C
Test Limits 750 kilohms - 35 megohms
Test Voltage 4 VDC
Dimensions 9 cm x 7 cm x 3 cm
Weight 0.1 kg