RS PRO RSDM-906X Series User manual

User Manual
RSDM-906X series
Stock number: 1919720 RSDM-9061 1919721 RSDM-9060
EN
rspro.com

3
Table of Contents
SAFETY INSTRUCTIONS..................................6
GETTING STARTED .......................................11
Characteristics .........................................................12
Front Panel Overview ...............................................14
Rear Panel Overview ................................................20
Status Bar ................................................................24
Set Up .....................................................................27
BASIC MEASUREMENT..................................29
Basic Measurement Overview ..................................30
AC/DC Voltage Measurement ..................................34
AC/DC Current Measurement ..................................42
2W/4W Resistance Measurement.............................47
Continuity Test.........................................................51
Diode Measurement ................................................54
Frequency/Period Measurement ..............................57
Capacitance Measurement .......................................63
Temperature Measurement ......................................67
DUAL MEASUREMENT ..................................78
Dual Measurement ..................................................79
ADVANCED MEASUREMENT .........................90
Advanced Measurement Overview ...........................91
Relative Value Measurement ....................................92
Hold Measurement ..................................................94
Trigger Setting .........................................................98
Filter Setting ..........................................................104
Math Measurement ...............................................109

4 rspro.com
DIGITAL I/O ................................................ 137
Digital I/O Overview ..............................................138
Application: Compare Mode...................................142
Application: 4094 / User Mode ..............................150
Application: External Trigger ..................................158
SYSTEM & FIRMWARE ................................ 160
View System Info ...................................................161
Firmware Update ...................................................162
MENU SETTING .......................................... 165
Configure System ...................................................166
Configure Display ..................................................189
SCREENHOT & LOG.................................... 211
Capture ..................................................................212
Save Reading .........................................................215
DISPLAY SETTING ....................................... 219
Digit ......................................................................220
Display...................................................................222
REMOTE CONTROL .................................... 245
Configure Interface ................................................246
Command Syntax ...................................................282
Command Set ........................................................286
Status system ........................................................370
APPENDIX ................................................... 375
Fuse Replacement ..................................................376
Battery Replacement ..............................................380
Factory Default Parameters ....................................382
Specifications ........................................................387
RSDM-9061............................................................389
RSDM-9060 ............................................................399

5
Dimensions ...........................................................409
Declaration of Conformity ......................................410

6 rspro.com
SAFETY INSTRUCTIONS
This chapter contains important safety
instructions that you must follow when operating
the RSDM-9060/9061 and when keeping it in
storage. Read the following before any operation
to insure your safety and to keep the RSDM-
9060/9061 in the best possible condition.
Safety Symbols
These safety symbols may appear in this manual or on the
instrument.
WARNING
Warning: Identifies conditions or practices that
could result in injury or loss of life.
CAUTION
Caution: Identifies conditions or practices that
could result in damage to the RSDM-9060/9061 or
to other objects or property.
DANGER High Voltage
Attention: Refer to the Manual
Protective Conductor Terminal
Earth (Ground) Terminal
Do not dispose electronic equipment as unsorted
municipal waste. Please use a separate collection
facility or contact the supplier from which this
instrument was purchased.

7
Safety Guidelines
General
Guideline
CAUTION
Make sure that the voltage input level does not
exceed DC1000V/AC750V.
Make sure the current input level does not
exceed 10A.
Do not place heavy objects on the instrument.
Avoid severe impact or rough handling that
may damage the instrument.
Do not discharge static electricity to the
instrument.
Use only mating connectors, not bare wires, for
the terminals.
Do not block or obstruct the cooling fan vent
opening.
Do not perform measurement at the source of a
low-voltage installation or at building
installations (Note below).
Do not disassemble the instrument unless you
are qualified as service personnel.
Make sure that the Sense LO terminal to Input
LO is limited to 2Vpk, the Sense HI to Sense LO
terminals are limited to 200Vpk and the Input
LO to earth is limited to 500Vpk.
(Note) EN 61010-1:2010 specifies the measurement categories and
their requirements as follows. The RSDM-9060/9061 falls under
category II 300V.
Measurement category IV is for measurement performed at the
source of a low-voltage installation.
Measurement category III is for measurement performed in a
building installation.
Measurement category II is for measurement performed on circuits
directly connected to a low voltage installation.

8 rspro.com
Power Supply
WARNING
AC Input voltage: 100/120/220/240 V AC
±10%, 50Hz / 60Hz / 400Hz ±10%
The power supply voltage should not fluctuate
more than 10%.
Connect the protective grounding conductor of
the AC power cord to an earth ground to
prevent electric shock.
WARNING
(RSDM-9061
only)
Due to the fact that the Front/Rear Input Switch
on the front panel is not proposed as an active
multiplexer, do Not change the input switch
when signals are present on either rear or front
set of terminals. Intrument damage and risk of
electric shock may occur if switching the input
switch when high voltage or current is present.
Fuse
WARNING
Fuse type: T0.25A 100/120 VAC
T0.125A 220/240 VAC
Make sure the correct type of fuse is installed
before power up.
To avoid risk of fire, replace the fuse only with
the specified type and rating.
Disconnect the power cord before fuse
replacement.
Make sure the cause of a fuse blowout is fixed
before fuse replacement.
Cleaning the
function
generator
Disconnect the power cord before cleaning.
Use a soft cloth dampened in a solution of mild
detergent and water. Do not spray any liquid
into the RSDM-9060/9061..
Do not use chemicals containing harsh products
such as benzene, toluene, xylene, and acetone.

9
Operation
Environment
Location: Indoor, no direct sunlight, dust free,
almost non-conductive pollution (Note below)
Humidity:
< 30°C: < 80%RH (non-condensing)
30°C~40°C: <70%RH (non-condensing)
>40°C: <50%RH (non-condensing)
Altitude: <2000m
(Note) EN 61010-1:2010 specifies pollution degrees and their
requirements as follows. The RSDM-9060/9061falls under degree 2.
Pollution refers to “addition of foreign matter, solid, liquid, or
gaseous (ionized gases), that may produce a reduction of dielectric
strength or surface resistivity”.
Pollution degree 1: No pollution or only dry, non-conductive
pollution occurs. The pollution has no influence.
Pollution degree 2: Normally only non-conductive pollution occurs.
Occasionally, however, a temporary conductivity caused by
condensation must be expected.
Pollution degree 3: Conductive pollution occurs, or dry, non-
conductive pollution occurs which becomes conductive due to
condensation which is expected. In such conditions, equipment is
normally protected against exposure to direct sunlight,
precipitation, and full wind pressure, but neither temperature nor
humidity is controlled.
Storage
environment
Location: Indoor
Relative Humidity: −40°C to 70°C
Temperature: <90%RH(non-condensing)
Disposal
Do not dispose this instrument as unsorted
municipal waste. Please use a separate collection
facility or contact the supplier from which this
instrument was purchased. Please make sure
discarded electrical waste is properly recycled to
reduce environmental impact.

10 rspro.com
Power cord for the United Kingdom
When using the function generator in the United Kingdom, make
sure the power cord meets the following safety instructions.
NOTE: This lead/appliance must only be wired by competent persons
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in this lead are coloured in accordance with the
following code:
Green/ Yellow:
Earth
Blue:
Neutral
Brown:
Live (Phase)
As the colours of the wires in main leads may not correspond with the
coloured marking identified in your plug/appliance, proceed as
follows:
The wire which is coloured Green & Yellow must be connected to the
Earth terminal marked with either the letter E, the earth symbol or
coloured Green/Green & Yellow.
The wire which is coloured Blue must be connected to the terminal
which is marked with the letter N or coloured Blue or Black.
The wire which is coloured Brown must be connected to the terminal
marked with the letter L or P or coloured Brown or Red.
If in doubt, consult the instructions provided with the equipment or
contact the supplier.
This cable/appliance should be protected by a suitably rated and
approved HBC mains fuse: refer to the rating information on the
equipment and/or user instructions for details. As a guide, a cable of
0.75mm2should be protected by a 3A or 5A fuse. Larger conductors
would normally require 13A types, depending on the connection
method used.
Any exposed wiring from a cable, plug or connection that is engaged
in a live socket is extremely hazardous. If a cable or plug is deemed
hazardous, turn off the mains power and remove the cable, any fuses
and fuse assemblies. All hazardous wiring must be immediately
destroyed and replaced in accordance to the above standard.

11
GETTING STARTED
This chapter describes the RSDM-9060/9061 in a
nutshell, including an Overview of its main
features and front / rear panel introduction.
After going through the Overview, follow the
Power-up sequence to properly setup the RSDM-
9060/9061.
Please note the information in this manual was
correct at the time of printing. However as RS
PRO continues to improve its products, changes
can occur at any time without notice. Please see
the RS PRO website for the latest information and
content.
Characteristics ........................................................ 12
Accessories ......................................................................................13
Front Panel Overview .............................................. 14
Measurement Keys (basic) ..............................................................17
Measurement Keys (advanced).......................................................18
Rear Panel Overview ............................................... 20
Status Bar ............................................................... 24
Set Up ..................................................................... 27
Horizontal/Tilt/Vertical Applications..............................................27
Power Up..........................................................................................28

12 rspro.com
Characteristics
The RSDM-9060/9061 is a portable, dual-display digital multimeter
suitable for a wide range of applications, such as production testing,
research, and field verification.
Performance
The highest DCV accuracy:
RSDM-9061: 35ppm
RSDM-9060: 75ppm
The highest current:
RSDM-9061: 10A
RSDM-9060: 3A
The highest voltage: 1000V
The highest ACV frequency response: 300 kHz
The fastest sampling rate:
1k Readings/sec (RSDM-9060)
10k Readings/sec (RSDM-9061)
Internal memory:
10k read memory (RSDM-9060)
100k read memory (RSDM-9061)
Data Logging to USB
Features
6
2
1
digits
Multi functions: ACV, DCV, ACI, DCI, 2W/4W
R, Hz, Temp, Continuity, Diode, Period,
Capacitance test, REL, dBm, Hold, MX+B, 1/X,
REF%, dB, Compare and Statistics.
Manual or Auto ranging
AC true RMS
Built-in DC Ratio function
Standard SCPI command set in emulation
compatible with Agilent 34401A
Up to 3 temerature measurements: RTD,
Thermistor and Thermocouples
(Cold-Junction Compensation)

13
Graph Display: BarMeter, TrendChart,
Histogram
Interface
USB device/RS232/GPIB(optional)/LAN for
remote control
9-pin Digital I/O port
USB device port supports USBCDC and
USBTMC
USB Host
Software
Excel Addins
DMM-VIEWER2
Accessories
Standard Accessories
Part number
Description
CD-ROM
UM, Software, Driver
82DM-90610M01
Safety Instruction Sheet
GTL-217
Test leads
GTL-246
USB Cable, USB 2.0, A-B type,
1200mm
Optional Accessories
Part number
Description
11DM-90610101
RSDM-9060/9061 GPIB Card
GTL-234
RS-232 Cable , 2000mm
GTL-205A
Temperature Probe Adapter
with Thermal Coupling (K-
type)
GTL-308
4W+Shield Test leads, 1.5M
RSDM-TL1
Test lead probes with CAT
IV 600V sheath x 2
Fine tip probes x 2
SMT Grabbers x 2
Mini Grabber x 1

14 rspro.com
Front Panel Overview
5 6 7
91011121314
4
2
1
3
RSDM-9060
5 6 7 8
91011121314
4
2
1
3
RSDM-9061
Item
Description
1
ESC (Escape) Key
2
Print screen / Data log Key
3
USB Host Port
4
Power Switch

15
5
Function keys (F1 through F6, functions vary per modes)
6
Measurement Keys
7
AC/DC Current Input Terminals (10 A terminal available
on RSDM-9061 only)
8
Front/Rear Input Switch (RSDM-9061 only)
9
HI and LO Input Terminals
10
HI and LO Input Terminals
11
Range Selection Keys
12
Knob key
13
Arrow Keys
14
Main Display
ESC (Escape) Key
Single press to escape from current page.
Presses and holds the ESC key for 2
seconds to toggle between full display
and simple display, which conceals the
status bar, math display as well as
additional info for lightweight use.
Screenshot / Data
Log Saving Key
Captures the current screenshot or saves
the data log for reading.
USB Host Port
Connects with USB flash drive for data
storage.
Power Switch
Turns On or Off the main
power. For the power up sequence.
Main Display
The 4.3”TFT LCD shows measurement results and
parameters.

16 rspro.com
Measurement
Keys
There are 4 rows in total of both basic and
advanced measurement keys deployed on the
front panel.
Function Keys
The 6 keys have varied functions per different
settings.
Knob Key
Scrolls the knob to select parameters
in various setting pages. Press the key
until click to confirm setting.
Arrow Keys
Presses the left or right arrow keys to
move parameter cursor rightward or
leftward per requirement.
Range Selection
Keys
Presses the Auto key to activate auto-
range mode, whilst clicking “+” or “–
“ key can increase or decrease range
parameter, respectively.
DC/AC 3A
Terminal
DC/AC current input
DC: 100μA~3A
AC: 100μA~3A
For the fuse replacement procedure.
Sense LO
Terminal
Accepts LO sense line in 4W
resistance measurement.
Sense HI Terminal
Accepts HI sense line in 4W resistance
measurement.

17
Input LO Terminal
Accepts ground (COM) line in all
measurements except the sense line in
4W Resistance.
The maximum withstand voltage
between this terminal and earth is
500Vpk.
Input HI
Terminal
Used as an input port for all
measurements except for DC/AC
Current measurements.
DC/AC 10A
Terminal
(RSDM-9061 only)
Accepts DC/AC Current input.
For DCI or ACI details.
Measurement Keys (basic)
Background
The upper 2 rows of measurement keys are used
for basic RSDM-9060/9061 measurements such as
voltage, current, resistance, continuity, diode,
frequency, period, capacitance and temperature.
Each key has a primary and secondary function
individually. The secondary function is accessed in
conjunction with the Shift key.
Shift
The Shift key is used to select the
secondary functions assigned to
each front panel key. When
pressed, the Shift indicator
appears in the display.
Local
For the Local key, it helps release
from the remote control and
returns the instrument to local
panel operation.
ACV
Measures AC Voltage.

18 rspro.com
Shift →ACV (ACI)
Measures AC Current
DCV
Measures DC Voltage.
Shift →DCV
(DCI)
Measures DC Current
Ω2W (Resistance)
Measures 2-wire Resistance.
Shift →Ω2W
(Ω4W Resistance)
Measures 4-wire Resistance.
(Continuity)
Tests Continuity.
Shift →
(Diode )
Tests Diode.
FREQ (Frequency)
Measures Frequency
Shift + FREQ
(Capacitance )
Measures Capacitance.
TEMP
(Temperature)
Measures Temperature.
Measurement Keys (advanced)
Background
The lower 2 rows of measurement keys are used
for more advanced functions. Each key has a
primary and secondary function. The secondary
function is accessed in conjunction with the Shift
key.
REL
Measures the Relative value
Shift →REL
(REL#)
Manually sets the reference value
for the Relative value
measurement.

19
Hold
Activates the Hold function.
Shift →Hold
(Hold#)
Manually sets the parameters for
the Hold measurement.
TRIG (Trigger)
Activates the Trigger function.
Shift →TRIG
(TRIG#)
Manually sets the parameters for
the Trigger function.
Menu
Enters the setting pages in various
Menus.
Shift →Menu
(Filter)
Manually sets the parameters for
the Filter function.
DISP
Display settings.
Shift →DISP
(Math)
The Math functions including dB,
dBm, Compare, MX+B, 1/X and
Percent manually.

20 rspro.com
Rear Panel Overview
240
1 3 4 5
78
9
10
RSDM-9060
240
1 2 3 4 5 6
78
9
10
1112
RSDM-9061
Item
Description
1
3A Current Terminal Fuse
2
3A Current Terminal (RSDM-9061 only)
3
RS-232 Interface Connector
4
USB Interface Connector (B Type)