Ruijie RG-R SR30 Series Installation and operating manual

RG-RSR30 Series Routers
Hardware Installation and Reference Guide 1.02

Copyright statement
Ruijie Networks©2000-2014
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,
modification, transmission, translation or commercial use of this document or any portion of this document,
in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.
, , , ,
, ,
, , ,
, , are registered trademarks of Ruijie
Networks. Counterfeit is strictly prohibited.
Exemption statement
This document is provided “as is”. The contents of this document are subject to change without any notice.
Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to
ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to
content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the router.
Scope
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks website: http://www.ruijienetworks.com
Online customer services: http://webchat.ruijie.com.cn
Customer service center: http://www.ruijie.com.cn/service.aspx
Customer services hotline: [phone]
BBS: http://support.ruijie.com.cn
Customer services email: [email protected]
Related Documents
Documents Description
Configuration Guide Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Documentation Conventions
The symbols used in this document are described as below:
This symbol brings your attention to some helpful suggestions and references.
This symbol means that you must be extremely careful not to do some things that may damage the device or
cause data loss.

Hardware Installation and Reference Guide Overview
Overview
The RSR30 series routers are proprietary data communication products independently developed by Ruijie Networks
Co. Ltd by using advanced semiconductor and communication control technologies. Ruijie series routers are
developed in full compliance with international standard, therefore, they are similar to major routers in terms of usage
and configuration. Network administrators familiar with the configuration commands of major routers can use RSR30
series routers without training.
RSR30 Series Routers
The RSR30 series has one model, namely RSR30-44.
RSR30-44 Router Overview
With modular design, high processing capability and high access density, the RSR30-44 can serve as the access
router of large branches and the convergence rotuer of small branches.
Using high performance microprocessor and Ruijie’s proprietary network operating system, the RSR30-44 supports
BGP, IP multicast, high spped forwarding and rich QoS features to offer comprehensive network solutions for the
industries such as telecommunications, private network, ISP, finance, tax, public security, and railways as well as
middle and large-sized enterprises.
The RSR30-44 is a modularized router that includes the RSR30-44 chasis and optional modules. It supports two types
of modules-SIC and NMX:
SIC module:
1-port non-channelized E1 interface card (SIC-1E1-F) (up to two cards are supported)
1-port channelized CE1 module (SIC-1CE1) (up to two cards are supported)
1-port high speed synchronous serial port interface card (SIC-1HS) (up to three cards are supported)
8-port high speed asynchronous serial port interface card (SIC-8A)
2-port FXS voice interface card (SIC-2FXS)
2-port FXO voice interface card (SIC-2FXO)
1-port ISDN basic rate U interface card(SIC-1B-U)
1-port ISDN basic rate S/T interface card(SIC-1B-S/T)
TD-SCDMA 3G WWAN module(SIC-3G-TD) (up to three cards are supported)
WCDMA 3G WWAN module(SIC-3G-WCDMA) (up to three cards are supported)
CDMA2000 3G WWAN module(SIC-3G-CDMA) (up to three cards are supported)
NMX module:
2-port Gigabit Ethernet network adapter (NMX-2GEH)
8-port E1/CE1 card (NMX-8E1/CE1H)
4-port E1/CE1 card (NMX-4E1/CE1H)

Hardware Installation and Reference Guide Overview
4-port high-speed synchronous serial interface module (NMX-4HSH)
1-port CPOS-STM1 line card (NMX-1CPOS-STM1H)
1-port ATM module (NMX-1ATM-STM1H)
24-port Layer 2 switching module (NMX-24ESW) (up to two modules are supported)
1-port POS module (NMX-1POS-STM1H)
6-port module (NMX-6FEH)
Ruijie Ipsec NMX encrypted module (NMX-SECH V1.X) (up to six modules are supported)
When purchasing the RSR30-44 modular routers, select functional modules following these rules:
Unless otherwise specified, up to four modules of the same type are supported.
Functional modules are related to slot position. Some modules may be inserted in one or several slots only. For
details, refer to the supported module list on the RSR30-44.
Interface cables shall match functional modules connected.
For more information on functional modules, refer to related sections.
The RSR30-44 supports V1.0 and V1.1 versions of NMX-2GEH, NMX-4HSH, and NMX-1CPOS-STM1H.
The V1.1 version of the above NMX modules must be used together with the 10.2 main program and
higher version, and it supports the hot-plugging. For the hot-plugging details, see the software manual.
RSR30-44 supports V1.0, V1.1 and V2.0 versions of NMX-8E1/CE1H and NMX-4E1/CE1H. The V1.1
version of the above NMX modules must be used together with the 10.2 main program and higher version,
and it supports the hot-plugging. For the hot-plugging details, see the software manual. The V2.0 version
of the above NMX modules must be used together with the 10.4(1) and higher version, and it supports the
hot-plugging. For the hot-plugging details, see the software manual.
All NMX modules are hot swapping, except for NMX-24ESW.
Highlights
High-density aggregate access and high processing capability
The RSR30-44 connects DDN, frame relay, or X.25 through Synchronous serial ports and enables high speed
forwarding through 1000M ports. Hence, it can serve as the core router of small- and media-sized enterprises and the
access rotuer of large branches.
Compatibility
The RSR30-44 is fully compatible with equipments of other suppliers.
Power supply

Hardware Installation and Reference Guide Overview
The RSR30-44 adopts GB4943-compliant power supplies to prevent surging, over-voltage, under-voltage and
over-current for stable, and reliable output with instant power-failure protection
Chassis
The RSR30-44 adopts standard 19in chassis, which can resist electromagnetic radiation, shock, high and low
temperature.
Certificate
The RSR30-44 has passed the access test of telecom network equipments by the MII
Appearance and Indicators
Front panel of The RSR30-44 router
Back panel of the RSR30-44 router
Parameters
The following table lists the parameters of the RSR30-44:
Item RSR30-44
Slot for control board 1 (at most one control module can be configured)

Hardware Installation and Reference Guide Overview
Slot for functional module Multiple as required (at most four NMX modules and four SIC modules can be
configured)
Slot for power module 2 (at most two modules can be configured)
External dimension (W x H
x D) 440 mm x 161.4 mm x 412 mm (excluding the hangers on both sides)
Input voltage AC100–240V 50–60Hz
Total power consumption < 150 W
Operating temperature 0 to 40°C
Storage temperature -40 to 70°C
Operating humidity 20–90%RH (non-condensing)
Slot Numbering
The slots of NMX moudle are numbered as below:
On the front panel, the slot for control board is numbered 0, and the rest numbered 1 to 4 from left to right and from
bottom to up, as shown in the following figure.
The slots of SIC moudle are numbered as below:
The slots of SIC moudle are located on the control module. On the front panel, the slots are numbered 5 to 8 from left to
right and from bottom to up, as shown in the following figure.
Supported Modules List
The following tables shows the modules supported on the RSR30-44:
Slot Number Line Card Supported Remarks

Hardware Installation and Reference Guide Overview
1 NMX-8E1H V2.XX, NMX-4E1H V2.XX,
NMX-4HSH V1.1X, NMX-24ESW V1.XX,
NMX-2GEH V1.1X, NMX-1CPOSH V1.1X,
NMX-1ATMH V1.XX, NMX-6FEH, NMX-SECH
V1.x
2 NMX-8E1H V2.XX, NMX-4E1H V2.XX,
NMX-4HSH V1.1X, NMX-2GEH V1.1X,
NMX-1CPOSH V1.1X, NMX-1ATMH V1.XX,
NMX-6FEH, NMX-SECH V1.x
NMX-24ESW is not supported
3 NMX-8E1H V2.XX, NMX-4E1H V2.XX,
NMX-4HSH V1.1X, NMX-24ESW V1.XX,
NMX-2GEH V1.1X, NMX-1CPOSH V1.1X,
NMX-1ATMH V1.XX, NMX-6FEH, NMX-SECH
V1.x
4 NMX-8E1H V2.XX, NMX-4E1H V2.XX,
NMX-4HSH V1.1X, NMX-2GEH V1.1X,
NMX-1CPOSH V1.1X, NMX-1ATMH V1.XX,
NMX-6FEH, NMX-SECH V1.x
NMX-24ESW is not supported
5 SIC-1B-S/T V1.XX, SIC-1B-U V1.XX, SIC-2FXS
V1.XX, SIC-2FX0 V1.XX, SIC-8A V1.XX
SIC-1E1-F, SIC-1CE1, SIC-1HS, SIC-3G-TD,
SIC-3G-WCDMA, SIC-3G-CDMA are not
supported
6 SIC-1HS V1.XX,SIC-1B-S/T V1.XX, SIC-1B-U
V1.XX, SIC-2FXS V1.XX, SIC-2FX0 V1.XX,
SIC-8A V1.XX, SIC-3G-TD, SIC-3G-WCDMA,
SIC-3G-CDMA
SIC-1E1-F, SIC-1CE1 are not supported
7 SIC-1B-S/T V1.XX, SIC-1B-U V1.XX, SIC-2FXS
V1.XX, SIC-2FX0 V1.XX, SIC-1HS V1.XX,
SIC-1E1-F V1.XX, SIC-8A V1.XX, SIC-1CE1
V1.XX, SIC-3G-TD, SIC-3G-WCDMA,
SIC-3G-CDMA
8 SIC-1B-S/T V1.XX, SIC-1B-U V1.XX, SIC-2FXS
V1.XX, SIC-2FX0 V1.XX, SIC-1HS V1.XX,
SIC-1E1-F V1.XX, SIC-8A V1.XX, SIC-1CE1
V1.XX, SIC-3G-TD, SIC-3G-WCDMA,
SIC-3G-CDMA
Introduction to Control Modules
RSR30-RCM44-512M-2GE
The RSR30-RCM44-512M-2GE is applicable to the RSR30-44 series routers.

Hardware Installation and Reference Guide Overview
Appearance and Indicators
Appearance of the RSR30-RCM44-512M-2GE
RSR30-RCM44-512M-2GE has two status indicators:
Power: indicating power status. Green and ON indicate the power module works normally; Green and off indicate
the power is faulty.
System: indicating system status. Green and flashing indicate the system is starting. Green and ON indicate the
system works properly. Red and off indicate the system is faulty. Off indicates the system is not powered on.
The RSR30-RCM44-512M-2GE has two optic-electric multiplexing 1000M Ethernet interfaces. Each RJ45 port has two
status indicators, namely Link/Act and 1000M. Each SFP port has one indicator, namely Link/Act.
Link/Act indicator: ON means this port is linked up with other network equipments; Flashing means data is
transmitting on the port; OFF means no connection is set up.
1000M indicator: ON means the data is transmitted at 1000 Mbps; OFF means the data is transmitted at 100
Mbps or 10 Mbps.
Module Attributes
Item RSR30-RCM44-512M-2GE
Default
Configuration
One Console port, one AUX port, two 10/100/1000M adaptive Ethernet ports/1000M SFP
optical transceiver ports (optic-electric multiplexing)
Extended slots Four types of extended slots, including one DDR slot and four SIC slots, which can be
configured as required
Processor PowerPC high performance processor
BOOT ROM 2 MB NOR FLASH
DDR
SDRAM 512MB (DDR333)
Data NAND FLASH 512 MB
It is recommended to use Telcast and Kingston U-shaped disc purchased through official channels.
DDR SDRAM serves as the main storage, namely memory.
FLASH stores main software.

Hardware Installation and Reference Guide Overview
Module Interface
1000M Ethernet interface
The RSR30-RCM44-512M-2GE comes with two 10/100/1000 Mbps Ethernet interfaces, each supports both optical and
electric connectors-RJ45 and SFP. Users may choose them according to actual needs.
The RSR30-RCM44-512M-2GE comes with four 1000 Base-FX SFP/LC pluggable optical interface modules. User may
choose them according to actual needs.
Available SFP
modules
Mini-GBIC-SX: 1-port 1000BASE-SX mini GBIC conversion module (LC interface)
Mini-GBIC-LX: 1-port 1000BASE-LX mini GBIC conversion module (LC interface)
Mini-GBIC-LH40: 1-port 1000BASE-ZX mini GBIC conversion module (LC connector), 40km
Mini-GBIC-ZX50: 1-port 1000BASE-ZX mini GBIC conversion module (LC connector), 50km
Mini-GBIC-ZX80: single port 1000BASE-ZX min GBIC conversion module (LC interface), 80km
Features of optional transmission media:
Transmission
media and
maximum
transmission
distance
1000BASE-SX: wavelength 850 nm
Maximum transmission distance of 62.5/125 um multimode fiber is 220m
Maximum transmission distance of 50/125 um multimode fiber is 500 m
1000BASE-LX: wavelength 1310nm
Maximum transmission distance of 62.5/125 um multimode fiber is 550m;
Maximum transmission distance of 62.5/125 um multimode fiber is 550m;
Maximum transmission distance of 9/125 um single-mode fiber is 10 km
1000BASE-LH: wavelength 1310nm
Maximum transmission distance of 9/125 um single-mode fiber is 4 0km;
1000BASE-ZX: wavelength 1550nm
Maximum transmission distance of 9/125 um single-mode fiber is 50km and 80km;
10/100/1000BASE-T: maximum transmission distance of category-5 UTP or STP is 100 m
SIC module interface
RSR30-RCM44-512M-2GE coems with four SIC slots. Users can select corresponding functional modules as necessry.
For details, refer to Section Supplrted Modules List.
Introduction to SIC Modules
SIC-8A Interface Card
SIC module model: SIC-8A
Appearance and Indicators
Appearance of SIC-8A

Hardware Installation and Reference Guide Overview
The module includes one SCSI DB68 connector with one RDY indicator, and eight ACT indicators.
RDY indicator: ON means the sub-card is powered on and initialized.
ACT indicator: Flash means data is transmitting on the port.
Attributes of the SIC-8A Card
The basic attributes are as below:
SIC-8A
Number of ports One
Interface type SCSI DB68 female connector
Cable 1-to-8 cable with crystal connector or 1-to-8 cable with crystal jack
Rate Each asyn serial interface supports 9600 to 115200 bps band rate, including
9600, 19200, 38400, 57600 and 115200 bps.
Flow control Hardware and software-based auto flow control
Operating Temperature: Operating temperature: 0°C ~40°C
Storage temperature: -40°C ~70°C
Humidity Operating humidity: 10%~90%
EMC EMI: GB 9254-1998 Class A
EMS: GB/T 17618-1998
Module Cable
Two types fo cables are available:
1-to-8 cable (crystal connector): one end is SCSIDB68 male, the other end is RJ45 crystal connector.
1-to-8 cable (crystal jack): one end is SCSIDB68 male, the other end is RJ45 crystal jack.
No cables are shipped with the module. Users need to purchase it separately.
SIC-1HS Sync Interface Card
SIC module model: SIC-1HS
Appearance and Indicators
Appearance of SIC-1HS

Hardware Installation and Reference Guide Overview
The module has a status indicator (LINK) and the sub-card RDY indicator.
LINK: ON means the physical connection between the synchronous port and external devices is set up and the
upper-level protocol is UP.
RDY: ON means the sub-card is powered on and initialized.
Attributes of the SIC-1HS Module
HS is the abbrevation of the synchronous serial port.The basic features are as follows:
SIC-1HS indexes
Protocol V.24/V.35, with automatic cable identification
Rate 9600-8.192M bps.
LED
Two
LINK: on when the cable is inserted
RDY: on when the motherboard detects the line card
Interface DB26
Operating Temperature: Operating temperature: 0°C ~40°C
Storage temperature: -40°C ~70°C
Humidity Operating humidity: 10%~90%
EMC EMI: GB 9254-1998 Class A
EMS: GB/T 17618-1998
Module Cable
The following cables can be used:
V.24 DTE
V.24 DCE
V.35 DTE
V.35 DCE
These cables are not shipped with RSR30 series routers. Users need purchase them separately. All types of cables of
SIC-1HS connect to the router through DB26 interface. Pay attention to connectors when purchasing cables.
ISDN Interface Card
SIC module model:
1-port ISDN U-interface card (SIC-1B-U)
1-port ISDNS/T interface card (SIC-1B-S/T)

Hardware Installation and Reference Guide Overview
Appearance and Indicators
Appearance of the 1-port ISDN U-interface card (SIC-1B-U)
Appearance of the 1-port ISDN S/T U-interface card (SIC-1B-S/T)
The module has the status indicator ACT and the sub-card indicator RDY. Moreover, two channel status indicators are
available-B1 and B2.
B1: ON means that B1 channel is working normally.
B2: ON means that B2 channel is working normally.
ACT: ON means that U interface or S/T is activated.
RDY: ON means the sub-card is powered on and initialized.
Attributes of the ISDN Interface Card
The basic attributes are as below:
SIC-1B-U
Number of ports One
Interface type RJ45 port (compatible with RJ11)
Cable Telephone wire
Standard compliance ITU-T I.430,Q.921,Q931
Operating Temperature: Operating temperature: 0°C ~40°C
Storage temperature: -40°C ~70°C
Humidity Operating humidity: 10%~90%
EMC EMI: GB 9254-1998 Class A
EMS: GB/T 17618-1998
SIC-1B-S/T
Number of ports One
Interface type RJ45 (compatible with RJ11)
Cable Telephone wire
Terminal resistance Built-in 100Ω
Standard compliance ITU-T I.430,Q.921,Q931
Operating Temperature: Operating temperature: 0°C ~40°C
Storage temperature: -40°C ~70°C
Humidity Operating humidity: 10%~90%

Hardware Installation and Reference Guide Overview
EMC EMI: GB 9254-1998 Class A
EMS: GB/T 17618-1998
Module Cable
SIC-1B-U and SIC-1B-S/T use standard telephone wires.
No cables are shipped with the module. Users need to purchase it separately.
E1 Interface Card
SIC module model:
1-port non-channelized E1 card (SIC-1E1-F)
1-port channelized CE1 card (SIC-1CE1)
Appearance and Indicators
Appearance of SIC-1E1-F
Appearance of SIC-1CE1
Attributes of SIC-1E1-F and SIC-1CE1
The basic attributes of SIC-1E1-F and SIC-1CE1 are as follows:
SIC-1E1-F and SIC-1CE1
Number of ports One
Interface type DB9 female connector
Cable Balanced cable or unbalanced cable
Standard compliance ITU-T G.703
Operating Temperature: Operating temperature: 0°C ~40°C
Storage temperature: -40°C ~70°C
Humidity Operating humidity: 10%~90%
EMC EMI: GB 9254-1998 Class A

Hardware Installation and Reference Guide Overview
EMS: GB/T 17618-1998
Module Cables
Two kinds of cables are available:
E1 balanced cable/DB9 male connector-RJ45 male connector/120Ω/3 meters: one end is DB9 male connector
and the other end is RJ45 crystal connector.
E1 unbalanced cable/DB9 male connector-2*BNC/75Ω/3 meters: one end is DB9 male connector and the other
end is two BNC male connectors.
No cables are shipped with the module. Users need to purchase it separately.
SIC-2FXS Interface Card
SIC module model: SIC-2FXS
Appearance and Indicators
Appearance of SIC-2FXS interface card
The interface card includes the IN USE indicators for ports and one ACT indicator.
IN USE indicator: ON means the port is active.
RDY indicator: ON means the sub-card is powered on and initialized.
Attributes of the SIC-2FXS Card
The basic attributes are as below:
SIC-2FXS
Number of ports Two
Interface type RJ45 connector (compatible with RJ11)
Cable Phone wire
Standard compliance Voice coding: G.711, G.729A and G.723.1
Operating Temperature: Operating temperature: 0°C ~40°C
Storage temperature: -40°C ~70°C
Humidity Operating humidity: 10%~90%
EMC EMI: GB 9254-1998 Class A
EMS: GB/T 17618-1998

Hardware Installation and Reference Guide Overview
Module Cable
The SIC-2FXS module uses standard phone wires.
No cables are shipped with the module. Users need to purchase it separately.
SIC-2FXO Interface Card
SIC module model: SIC-2FXO
Appearance and Indicators
Appearance of the SIC-2FXO interface card
The interface card includes the IN USE indicators for ports and one ACT indicator.
IN USE indicator: ON means the port is active.
RDY indicator: ON means the sub-card is powered on and initialized.
Attributes of the SIC-2FXO Card
The basic attributes are as below:
SIC-2FXO
Number of ports Two
Interface type RJ45 connector (compatible with RJ11)
Cable Phone wire
Standard compliance Voice code: G.711, G.729A and G.723.1
Operating Temperature: Operating temperature: 0°C ~40°C
Storage temperature: -40°C ~70°C
Humidity Operating humidity: 10%~90%
EMC EMI: GB 9254-1998 Class A
EMS: GB/T 17618-1998
Module Cable
The SIC-2FXO module uses standard phone wires.
No cables are shipped with the module. Users need to purchase it separately.
SIC-3G-TD Interface Card
SIC card model: SIC-3G-TD

Hardware Installation and Reference Guide Overview
Appearance and Indicators
Appearance of the SIC-3G-TD interface card
Panel indicator description:
Indicator Description
RDY Solid on means that firmware initialization of the line card is complete.
OFF means the firmware initialization of the line card is not complete or fails.
WWAN Solid on means the link is through.
Flashing means the data is being transmitted.
RSSI
Solid on means the strong signal.
Flashing means the medium/low signal.
Off means the weak signal or no signal.
HSDPA Solid on means the HSDPA service is effective.
Off means there is no HSDPA service.
EDGE Solid on means the EDGE service is effective.
Off means there is no EDGE service.
Attributes of the SIC-3G-TD Card
The basic attributes are as below:
SIC-3G-TD
Number of ports SMA RF: 1
RJ-45: 1
Interface type SMA RF is used to connect antenna.
RJ45 is for the internal commissioning.
Cable SMA RF : N/A
RJ45: Serial port cable
Supported Rate HSDPA (in theory: 2.8 Mbps downlink and 384 kbps uplink)
Operating Temperature Operating temperature: 0°C ~45°C
Storage temperature: -40°C ~70°C
Humidity Operating humidity: 10%~90%
EMC EMI: GB 9254-1998 Class A
EMS: GB/T 17618-1998

Hardware Installation and Reference Guide Overview
When the module runs normally, the RJ-45 interface does not need to connect a cable.
Module Cable
The SMA interface of the SIC-3G-TD module can connect two types of antennas: pole-shaped antenna and 3m
extension magnetic antenna.
Pole-shaped antenna
Pole-shaped antenna specifications
Attribute Parameter
Frequency range 824-960 MHz/1710-2170 MHz
VSWR ≤ 3
Input impedance 50 ohms
Gain 1.8 dBi (824 MHz-960 MHz)
2.0 dBi (1710 MHz-2170 GHz）
Polarization Linear
Interface type SMA Straight Plug Reverse
Length 145mm
Color Black
Operating temperature -10℃to 60℃
Cable length None
3m extension magnetic antenna (ANT-RJ3G3MA)

Hardware Installation and Reference Guide Overview
Specifications of 3m extension magnetic antenna (ANT-RJ3G3MA):
Attribute Parameter
Frequency range 824-960 MHz/1710-2170 MHz
VSWR ≤ 2.5
Input impedance 50 ohms
Gain ≥ 3dBi
Polarization Vertical
Interface type SMA-J
Length 224mm
Color Black
Operating temperature -40℃to 60℃
Cable length 3m
Installing the SIM Card
1) Open the SIM slot according to the indicated OPEN direction.
2) Insert the SIM card into the slot.
3) Close the slot in the opposite direction of OPEN.

Hardware Installation and Reference Guide Overview
1. The gap of the SIM card should be aligned with that of the SIM slot. In this manner, the SIM card can be
installed correctly.
2. The SIM slot should be closed when there is no SIM card in it. Otherwise, there are risks of damaging
the SIM slot.
SIC-3G-CDMA Interface Card
SIC card model: SIC-3G-CDMA
Appearance and Indicators
Appearance of the SIC-3G-CDMA interface card
Panel indicator description:
Indicator Description
RDY Solid on means that firmware initialization of the line card is complete.
OFF means the firmware initialization of the line card is not complete or fails.
WWAN Solid on means the link is through.
Flashing means the data is being transmitted.