Ruijie RSR10 Series Assembly instructions

Ruijie RSR10/RSR20 Series Routers
Hardware Installation Manual (V2.00)

Ruijie RSR10/RSR20 Series Routers Installation Manual
Revision No.: Version 2.00
Date:
Copyright Statement
Ruijie Networks Ltd. ©2000-2012
All rights reserved.
Title to this manual shall solely remain with Ruijie Networks Ltd. Without our written permission, this
document may not be excerpted, reproduced, transmitted, or otherwise in all or in part by any party in any
means.
Ruijie Networks Ltd. reserves the right to update this manual without notice.
RGOS®、RGNOS®、锐捷®、®、® 、® 、
® and are all registered trademarks of
Ruijie Networks Ltd. and are protected by law.

Preface
Thank you for buying Ruijie series of routers. This manual details the steps that you need to
follow to install them.
Version Description
This manual applies to Ruijie RSR10/RSR20 series routers.
Contents
This manual provides the hardware features, installation setting, maintenance, and fixing of
common problems of Ruijie RSR10/RSR20 series routers.
For your safety, the information in this manual must be followed to prevent property damage
and personal injury.
Suggestion
It is suggested that the router should be installed and configured by
professional technicians who are familiar with electronic environment and
cable connection and have experience in installing and configuration
routers.
This manual consists of the following chapters:
Chapter 1 Product Overview
Presents an introduction to Ruijie RSR10/RSR20 series routers and the system
features
Chapter 2 Preparing for Installation
Concerned with the environmental requirements for installing Ruijie RSR10/RSR20
series routers, precautions for installation, and the tools needed.
Chapter 3 Installing Router
Presents mechanical installation, power supply connection, backup port cable
connection, and console port connection of Ruijie RSR10/RSR20 series routers
Chapter 4 Starting and Configuring Router
Provides initial start information and initial configuration of the router.
Chapter 5 Troubleshooting
Offers troubleshooting tips during the installation
Chapter 6 Use of Cables
Introduces the use of affiliated cables.

Note
This manual only provides information on the installation of Ruijie
RSR10/RSR20 series routers. The routers must be configured before use.
For information on the configuration of the routers, see the Configuration
Reference. For information about functions supported by the routers, see the
release notes of the relating software.
Information found on the by-packed CD about the description and
configuration shall prevail. Ruijie Networks Ltd. reserves the right to update it
without notice.
Related Documents
For the command description and software configuration guide of the RSR10/RSR20 series
routers, please refer to the related command reference manual and configuration guide.
Obtaining Documentation
You can obtain the documentation you need through the following channels:
Internet:
You can obtain the latest on-line documentation at:
http://www.ruijie.cn
Information Feedback
If you read the product documentation of Ruijie Networks on the Internet, you can send
any of your comments on our documentation on line.
You can also send any of your comments on our documentation via E-Mail at:
[email protected]
You can also mail any of your comments on our documentation to:
Address: Juyuanzhou 19-22 Star-net Ruijie Science-based Industrial Park, 618 Jinshan
Road, Fuzhou city
Ruijie Networks Ltd.
Postcode: 350002
Your valuable inputs are highly appreciated.

Obtaining Technical Assistance
Ruijie Networks provides excellent technical support services for all our products. You can
obtain the technical assistance you need through any of the following channels:
Ruijie Networks Website
From which you can obtain the latest product documentation, causes and problems
analysis of product faults, application solutions, and software upgrade.
Customer service center of Ruijie Networks
Customer Service Center of Ruijie Network provides all customers with needed
technical assistance: product, technology and solutions. The customer service center
provides responsive technical support for your product installation problems, software
configuration problems, and other network performance problems.
Technical Support Website: http://support.ruijie.com.cn
Technical Support E-mail: [email protected].cn
Call center hot-line: 4008-111-000
Service complaint hot-line: 0591-83057315
Target Readers
This manual is intended for the following readers:
Network engineers
Technical salespersons
Network administrators
Conventions in this Document
1. Universal Format Convention
Arial: Arial with the point size 10 is used for the body.
Arial: The warnings and notes use the Arial font, with lines added at the top and bottom for
separation from the main body.
Terminal Display: self-defined Terminal Display, in Courier New front, with the size of 8,
meaning the message displayed on the screen. User's entries among the information shall
be indicated with bolded characters.
2. Signs
Conspicuous signs are used in this document to alert the special attentions during the
operation. The meanings of these signs are described as below:

Warning
Warning, danger or alert in the operation.
Caution
Precaution, attention or reminder in the operation.
Note
Note, prompt, tip or any other necessary supplement or explanation for the
operation.

1
Contents
1Product Overview................................................................................................................................ 1-1
1.1 RSR10 Series Routers...............................................................................................................1-1
1.1.1 RSR10-02......................................................................................................................1-1
1.2 RSR20 Series Routers...............................................................................................................1-5
1.2.1 RSR20-04 Series Routers.............................................................................................1-5
1.2.2 RSR20-14 Series Routers.............................................................................................1-8
1.2.3 RSR20-18 Series Routers.......................................................................................... 1-13
1.2.4 RSR20-24 Series Routers.......................................................................................... 1-18
1.3 SIC Card Introduction ............................................................................................................. 1-23
1.3.1 SIC-1HS Sync Interface Card .................................................................................... 1-23
1.3.2 SIC-1HS-V35 Sync Interface Card............................................................................. 1-26
1.3.3 ISDN Interface Card................................................................................................... 1-28
1.3.4 SIC-1E1- F Interface Card ......................................................................................... 1-30
1.3.5 SIC-4ESW Interface Card .......................................................................................... 1-32
1.3.6 SIC-8A Interface Card ................................................................................................ 1-35
1.3.7 SIC-1A Interface Card ................................................................................................ 1-39
1.3.8 SIC-2FXS Interface Card ........................................................................................... 1-41
1.3.9 SIC-2FXO Interface Card........................................................................................... 1-42
1.3.10 SIC-1CE1 Interface Card ........................................................................................... 1-43
1.3.11 SIC-3G-TD Interface Card ......................................................................................... 1-44
1.3.12 SIC-3G-CDMA Interface Card.................................................................................... 1-48
1.3.13 SIC-3G-WCDMA Interface Card ................................................................................ 1-53
1.3.14 Other SIC Cards......................................................................................................... 1-57
1.4 NMX Card ............................................................................................................................... 1-57
1.4.1 NMX-24ESW Interface Card ...................................................................................... 1-57
1.4.2 NMX-24ESW-L2 Interface Card................................................................................. 1-58
1.4.3 NMX-2GEH Interface Card ........................................................................................ 1-59
1.4.4 NMX-4HSH Interface Card......................................................................................... 1-61
1.4.5 NMX-4(8)E1/CE1H Interface Card............................................................................. 1-63
1.5 Features of RSR10/RSR20 Series Routers ........................................................................... 1-65
1.5.1 Rich Protocol Support ................................................................................................ 1-65
1.5.2 Friendly User Interfaces ............................................................................................. 1-66
1.5.3 Powerful Backup Function ......................................................................................... 1-66
1.5.4 Rich Diagnosis and Management Tools..................................................................... 1-66
1.5.5 Superior Security........................................................................................................ 1-66
1.5.6 Diversified Terminal Functions ................................................................................... 1-67

2
1.5.7 Easy Upgrade............................................................................................................. 1-67
2Preparing for Installation ..................................................................................................................... 2-1
2.1 Safety Precautions.....................................................................................................................2-1
2.2 Installation Environment Requirements .....................................................................................2-1
2.2.1 Temperature and Humidity Requirements ....................................................................2-1
2.2.2 Cleanness Requirements..............................................................................................2-2
2.2.3 Anti-static Requirements ...............................................................................................2-3
2.2.4 Anti-interference Requirements ....................................................................................2-3
2.2.5 Anti-lightning Requirements ..........................................................................................2-3
2.2.6 Checking the Installation ...............................................................................................2-4
2.3 Installation Tools and Equipment ...............................................................................................2-4
3Installing Router .................................................................................................................................. 3-1
3.1 Procedure for Installing Router ..................................................................................................3-1
3.2 Fastening Router .......................................................................................................................3-2
3.2.1 Mounting in the Cabinet ................................................................................................3-2
3.2.2 Mounting on the Workbench .........................................................................................3-5
3.3 Installing the Power Cable and Grounding Cable......................................................................3-5
3.4 Connecting the Console ............................................................................................................3-6
3.5 Installing Cards ..........................................................................................................................3-6
3.5.1 Installing Line Cards......................................................................................................3-6
3.5.2 Removing Line Cards....................................................................................................3-7
3.5.3 Troubleshooting.............................................................................................................3-8
3.6 Installation Check.......................................................................................................................3-8
4Starting and Configuring Router.......................................................................................................... 4-1
4.1 Starting Router ...........................................................................................................................4-1
4.1.1 Setting Up the Configuration Environment....................................................................4-1
4.1.2 Powering on Router ......................................................................................................4-1
4.1.3 Startup Process .............................................................................................................4-2
4.2 Configuring Router.....................................................................................................................4-3
5Troubleshooting .................................................................................................................................. 5-1
5.1 Troubleshooting Power Faults ...................................................................................................5-1
5.2 Troubleshooting Configuration Faults........................................................................................5-1
6Cable Connection................................................................................................................................ 6-1
6.1 Physical Cable Connection........................................................................................................6-1
6.1.1 Connecting An Asyn Interface .......................................................................................6-1
6.1.2 Connecting A Synchronous Interface ............................................................................6-3

3
6.1.3 Connecting An E1 Interface ..........................................................................................6-4
6.1.4 Connecting the Console Interface.................................................................................6-5
6.2 Order Information.......................................................................................................................6-5

Installation Manual Chapter 1 Product Overview
1-1
1Product Overview
The RSR10/RSR20 series routers is a data communication product independently
developed by Ruijie Networks Co. Ltd. by using advanced semiconductor technologies and
communication control technologies Ruijie series routers are developed in full compliance
with international standards, therefore, it is similar to major routers in terms of use and
configuration approach. Network administrators who are familiar with the configuration
commands of major routers may use the routers without receiving training first.
1.1 RSR10 Series Routers
The RSR10 series routers are available in one model: RSR10-02.
1.1.1 RSR10-02
1.1.1.1 Overview
The RSR10-02 modular router is an enterprise-oriented network product independently
developed by Ruijie Networks. Designed with a modular structure and 32-bit
high-performance RISC microprocessor technology, it is based on our independently
developed high-performance network operating system platform, which is compatible with
the standard configuration GUIs of the mainstream products and delivers easy configuration.
The RSR10-02 router provides a great variety of network security features. It delivers a
sophisticated redundancy backup solution and IP multicast protocols, and provides rich QoS
features, offering a three-network-in-one solution for medium/small-sized enterprises.
The RSR10-02 supports up to 2 SIC line cards.
For the easy to use, each slot is marked with the supported card type, as shown in the
following figure.

Chapter 1 Product Overview Installation Manual
1-2
The SIC line cards are divided into 4 types, as shown in the following table.
SIC Type Supported SIC line card
Class A SIC-1A, SIC-8A, SIC-1B-U, SIC-1B-S/T, SIC-2FXS, SIC-2FXO
Class B SIC-1HS,SIC-3G-TD, SIC-3G-CDMA, SIC-3G-WCDMA
Class C SIC-1CE1, SIC-1E1-F
Class D SIC-4ESW
The following table shows the SIC cards supported by the RSR10-02 slots.
Class A Class B Class C Class D
Slot 1 √√√√
Slot 2 √√√
Note
1. Once SIC-4ESW is inserted, the Eth0/1 on the panel is not available.
2. The SIC-3G-TD, SIC-3G-CDMA and SIC-3G-WCDMA can be inserted
into the SIC 1. The SIC-2FXS cannot be inserted into the SIC 2.
1.1.1.2 Highlights
Access density and processing capability
RSR10-02 supports up to two non-channelized E1, two ISDN U or S/T interfaces, two
sync serial interfaces, two 3G interface cards, four Layer-2 switching Ethernet
interfaces and 16 asyn serial interfaces to provide the high-density remote OA solution.
The E1 interface complies with ITU-T G.703; the ISDN U interface complies with ITU-T
G.961 ANSI T1.601, and the ISDN S/T interface complies with ITU-T I.430. The sync
serial port can connect the networks such as DDN, frame relay, and X.25. These make
the router suitable as an access router for small/medium-sized branches.
Reliability
Backup center technology greatly improving network reliability, various backup modes
available for high reliability requirements
Compatibility
Fully compatible with equipment of other suppliers
Power supply
By using high-quality standard power supplies, it provides protection for surge,
overvoltage, undervoltage, overcurrent and other power problems to deliver stable and
reliable output, and supports transient power interruption protection.

Installation Manual Chapter 1 Product Overview
1-3
External structure
Using the standard chassis shielding electromagnetic radiation, it can be mounted on
the rack. It is highly resistant to shock, high/low temperatures, and electromagnetic
radiation, and works stably.
Certification
Passed the test of telecom access network equipment by the MII
1.1.1.3 Indicators and Appearance
Figure 1-1 Front panel of Ruijie RSR10-02 router
○1 Indicator;
○2 Console;
○3 Interface Ethernet 0/0;
○4 Interface Ethernet 0/1;
Indicator Description
Status Solid on: the system works well.
OFF or flashing: the system does not work well.
S 1~2
Green on when a SIC card is inserted in the SIC X card slot
and works well.
Green off when the SIC card is not inserted in the SIC X
card slot or does not work well.

Chapter 1 Product Overview Installation Manual
1-4
Figure 1-2 Back panel of Ruijie RSR10-02 router
○1 SIC card slot1;
○2 SIC card slot2;
○3 Powerswitch;
○4 Input power interface;
○5 Enclosure ground interface;
Note
If you cannot determine the number of the slot where the current module
resides, you can execute the show slots command in the privileged EXE
mode. The router version information includes the slot number of each
module.
1.1.1.4 Parameters
The following table lists the parameters of RSR10-02:
Item RSR10-02
Default Configuration One Console port, two 10/100M Ethernet ports
SIC card slot 2 (User can configure up to two SIC cards in
according to requirement.)
Processor RISC high performance processor
SDRAM 64MB
Boot Rom 2MB
Data
NAND FLASH 32MB
Dimensions (W×H×D) 268mm×44mm×185mm (1U)
Input voltage AC100~240V 50~60Hz
Whole-system power consumption < 20W
Operating ambient temperature 0~45°C

Installation Manual Chapter 1 Product Overview
1-5
Storage ambient temperature -40~70°C
Operating humidity 10~90%RH
1.2 RSR20 Series Routers
Currently RSR20 series comes with four models: RSR20-04, RSR20-14, RSR20-18, and
RSR20-24.
1.2.1 RSR20-04 Series Routers
1.2.1.1 Overview
The RSR20-04 modular router is an enterprise-oriented network product independently
developed by Ruijie Networks. Designed with a modular structure and 32-bit
high-performance RISC microprocessor technology, it is based on our independently
developed high-performance network operating system platform, which is compatible with
the standard configuration GUIs of the mainstream products and delivers easy configuration.
The RSR20-04 router provides a great variety of network security features. It delivers a
self-contained redundancy backup solution and IP multicast protocols, and provides rich
QoS features, offering a three-network-in-one solution for medium/small-sized enterprises.
The RSR20-04 supports up to 4 SIC line cards.
For the easy to use, each slot is marked with the supported card type, as shown in the
following figure.
The SIC line cards are divided into 4 types, as shown in the following table.
SIC Type Supported SIC line card
Class A SIC-1A, SIC-8A, SIC-1B-U, SIC-1B-S/T, SIC-2FXS, SIC-2FXO
Class B SIC-1HS, SIC-3G-TD, SIC-3G-CDMA, SIC-3G-WCDMA,
SIC-1HS-V35
Class C SIC-1CE1, SIC-1E1-F

Chapter 1 Product Overview Installation Manual
1-6
Class D SIC-4ESW
The following table shows the SIC cards supported by the RSR20-04 slots.
Class A Class B Class C Class D
Slot 1 √
√
Slot 2 √√
Slot 3 √√√
Slot 4 √√√
Note
Once SIC-4ESW is inserted, the Eth0/1 on the panel is not available.
1.2.1.2 Highlights
Access density and processing capability
RSR20-04 supports up to two non-channelized E1、four ISDN U or S/T interfaces, three
sync serial interfaces, three 3G interface cards, four Layer 2 switching Ethernet
interfaces, and 32 asyn serial interfaces to provide the high-density remote OA solution.
The E1 interface complies with ITU-T G.703; the ISDN U interface complies with ITU-T
G.961 ANSI T1.601, and the ISDN S/T interface complies with ITU-T I.430. The sync
serial port can connect the networks such as DDN, frame relay, and X.25. These make
the router suitable as an access router for large/medium-sized branches.
Reliability
Backup center technology greatly improves network reliability, various backup modes
are available for high reliability requirements
Compatibility
Fully compatible with equipments of other suppliers
Power supply
By using high-quality standard power supplies, it provides protection for surge,
overvoltage, undervoltage, overcurrent and other power problems to deliver stable and
reliable output, and supports transient power interruption protection.
External Structure
Using the standard 19" chassis shielding electromagnetic radiation, it can be installed
on racks, It is highly resistant to shock, high/low temperatures, and electromagnetic
radiation, and works stably.

Installation Manual Chapter 1 Product Overview
1-7
Certification
Passed the test of telecom access network equipment by the MII
1.2.1.3 Indicators and Appearance
Figure 1-3 Front panel of Ruijie RSR20-04 router
○1 Indicator;
○2 Console;
○3 Backup interface AUX;
○4 Interface Ethernet 0/0;
○5 Interface Ethernet 0/1;
Panel indicator description:
Indicator Description
Status Solid on: the system works well.
OFF or flash means the system does not work well.
S 1~4
Green on when a SIC card is inserted in the SIC X card slot
and works well.
Green off when the SIC card is not inserted in the SIC X card
slot or does not work well.
Figure 1-4 Back panel of Ruijie RSR20-04 router
○1 SIC card slot1;
○2 SIC card slot2;
○3 SIC card slot3;
○4 SIC card slot4;
○5 Powerswitch;

Chapter 1 Product Overview Installation Manual
1-8
○6 Input power interface;
○7 Enclosure ground interface;
Note
If you cannot determine the number of the slot where the current module
resides, you can execute the show slots command in the privileged EXE
mode. The router version information includes the slot number of each
module.
.
1.2.1.4 Parameters
The following table lists the feature parameters of Ruijie RSR20-04
Item RSR20-04
Default Configuration One Console port, one AUX port, and two 10/100M
Ethernet ports
SIC card slot 4 (In according with user’s requirement, configure up
to four SIC cards)
Processor RISC high performance network processor
BOOT ROM 2MB
SDRAM 128MB
Data
NAND FLASH 32MB
Dimensions (W×H×D) 437 mm × 44 mm × 268 mm (including the foot pads)
(1U)
Input voltage AC100~240V 50~60Hz
Whole-system power
consumption < 30W
Operating ambient temperature 0~45°C
Storage ambient temperature -40~70°C
Operating humidity 10~90%RH
1.2.2 RSR20-14 Series Routers
1.2.2.1 Overview
The RSR20-14 modular router is an enterprise-oriented network product independently
developed by Ruijie Networks. Designed with a modular structure and 32-bit

Installation Manual Chapter 1 Product Overview
1-9
high-performance RISC microprocessor technology, it is based on our independently
developed high-performance network operating system platform, which is compatible with
the standard configuration GUIs of the mainstream products and delivers easy configuration.
The RSR20-14 router provides a great variety of network security features. It delivers a
self-contained redundancy backup solution and IP multicast protocols, and provides rich
QoS features, offering a three-network-in-one solution for small- and medium-sized
enterprises.
RSR20-14 is suitable for the following environments:
Supports multiple access methods
Integrates switch and rotuer to save investments
Processes huge data flexibly at present and in the future
Enables ease of management.
Makes no damage to interfaces in a complicated financial site environment
Connects asyn interface terminals, entwork terminals and PCs at the same time
Addresses the security requirements in the finance industry
Serves as the access router of large- and medius-sized branches
The RSR20-14 can be configured with up to four SIC cards and one NMX switch module.
For the easy to use, each slot is marked with the supported card type.The SIC line cards are
divided into 4 types, as shown in the following table.
SIC Type Supported SIC line card
Class A SIC-1A, SIC-8A, SIC-1B-U, SIC-1B-S/T, SIC-2FXS, SIC-2FXO,
Class B SIC-1HS ,SIC-1HS-V35, SIC-3G-TD, SIC-3G-CDMA,
SIC-3G-WCDMA
Class C SIC-1CE1, SIC-1E1-F
Class D SIC-4ESW
The following table shows the SIC cards supported by the RSR20-14 slots.
Class A Class B Class C Class D
Slot 1 √
√
Slot 2 √√
Slot 3 √√√
Slot 4 √√√
The following table shows the NMX card that the NMX card slot supports:

Chapter 1 Product Overview Installation Manual
1-10
NMX Slots 5
NMX-24ESW √
NMX-24ESW-L2 √
Note
The NMX switch module, SIC-4ESW and the Eth0/1 on the panel cannot be
used at the same time. They are prioritized in the following order: NMX switch
module > SIC-4ESW > Eth0/1. That is, once the NMX switch module is
inserted, the SIC-4ESW and Eth0/1 cannot be used. When the SIC-4ESW is
inserted without the NMX switch module, the Eth0/1 cannot be used. The
Eth0/1 can be used only when the NMX switch module and SIC-4ESW are
not inserted.
For the information about SIC cards, see relevant sections in this chapter.
1.2.2.2 Highlights
Access density and processing capability
RSR20-14 comes with four SIC slots, which supports up to two non-channelized E1、
four ISDN U or S/T interfaces, three sync serial interfaces, three 3G interface cards,
four Layer 2 switching Ethernet interfaces, and 32 asyn serial interfaces to provide the
high-density remote OA solution. Moreover, RSR20-14 comes with one NMX slot that
supports 24 Layer 2 switching Ethernet interfaces. The E1 interface complies with
ITU-T G.703; the ISDN U interface complies with ITU-T G.961 ANSI T1.601, and the
ISDN S/T interface complies with ITU-T I.430. The sync serial port can connect the
networks such as DDN, frame relay, and X.25. These make the router suitable as an
access router for large/medium-sized branches.
Reliability
Backup center technology greatly improves network reliability, various backup modes
are available for high reliability requirements
Compatibility
RSR20-14 is fully compatible with equipments of other suppliers
Power supply
By using high-quality power supplies, RSR20-14 provides protection for surge,
overvoltage, undervoltage, overcurrent and other power problems to deliver stable and
reliable output, and supports transient power interruption protection.
External Structure
With the standard 19" chassis shielding electromagnetic radiation, RSR20-14 can be
installed on racks. It is highly resistant to shock, high/low temperatures, and
electromagnetic radiation, and works stably.