Ruijie RG-RSR20-XA Series Installation and operating manual

RG-RSR20-XA Series Routers
Hardware Installation and Reference Guide
Document Version: V1.3
Date: 2022-10-31
Copyright © 2023 Ruijie
Networks

Copyright
Copyright © 2023 Ruijie Networks
All rights are reserved in this document and this statement.
Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this document
or any portion of this document, in any form or by any means, without the prior written consent of Ruijie Networks
is prohibited.
Trademark and are owned by Ruijie Networks.
All other trademarks or registered trademarks mentioned in this document are owned by their respective owners.
Disclaimer
The products, services, or features you purchase are subject to commercial contracts and terms. Some or all of
the products, services or features described in this document may not be within the scope of your purchase or
use. Unless otherwise agreed in the contract, Ruijie Networks does not make any express or implied statement
or guarantee for the content of this document.
Due to product version upgrades or other reasons, the content of this document will be updated from time to
time. Ruijie Networks reserves the right to modify the content of the document without any notice or prompt.
This manual is for reference only. Ruijie Networks endeavors to ensure content accuracy and will not shoulder
any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

I
Preface
Intended Audience
This document is intended for:
Network engineers
Technical support and service engineers
Network administrators
Technical Support
Ruijie Networks website: https://www.ruijienetworks.com/
Technical support website: https://ruijienetworks.com/support
Case portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical support email: s[email protected]
Skype: [email protected]
Conventions
1. Conversions
Convention
Description
Bold font
Commands, command options, and keywords are in bold font.
Italic font
Arguments for which you supply values are in italic font.
[ ]
Elements in square brackets are optional.
{ x | y | z }
Alternative keywords are grouped in braces and separated by
vertical bars.
[ x | y | z ]
Optional alternative keywords are grouped in brackets and
separated by vertical bars.
&<1-n>
The argument before the sign (&) can be input for consecutive 1- n
times.
//
Double slashes at the beginning of a line of code indicate a
comment line.
2. Signs
The signs used in this document are described as follows:

II
Warning
An alert that calls attention to important rules and information that if not understood or followed can result in
data loss or equipment damage.
Caution
An alert that calls attention to essential information that if not understood or followed can result in function
failure or performance degradation.
Note
An alert that contains additional or supplementary information that if not understood or followed will not lead to
serious consequences.
Specification
An alert that contains a description of product or version support.
3. Note
The manual offers configuration information (including model, port type and command line interface) for
indicative purpose only. In case of any discrepancy or inconsistency between the manual and the actual version,
the actual version prevails.

i
Contents
Preface...................................................................................................................................................I
1 Product Overview...............................................................................................................................1
1.1 Introduction to RG-RSR20-XA Series.......................................................................................1
1.2 RG-RSR20-XA-24......................................................................................................................1
1.2.1 Package Contents..........................................................................................................1
1.2.2 Product Appearance ......................................................................................................2
1.2.3 Technical Specifications.................................................................................................6
1.3 RG-RSR20-XA-36......................................................................................................................8
1.3.1 Package Contents..........................................................................................................8
1.3.2 Product Appearance ......................................................................................................9
1.3.3 Technical Specifications...............................................................................................13
1.4 RG-RSR20-XA-54....................................................................................................................15
1.4.1 Package Contents........................................................................................................15
1.4.2 Product Appearance ....................................................................................................16
1.4.3 Technical Specifications...............................................................................................20
1.5 RG-PA150IB-F Power Module ................................................................................................22
1.5.1 Module Appearance.....................................................................................................22
1.5.2 Technical Specifications...............................................................................................22
1.6 Service Modules......................................................................................................................23
1.6.1 HSIC-2E1/CE1 Service Module...................................................................................23
1.6.2 HSIC-4G-LTE Service Module.....................................................................................25
1.7 Pluggable Modules..................................................................................................................26
1.7.1 GE Optical Modules.....................................................................................................27

ii
1.7.2 10GE Optical Modules.................................................................................................28
1.8 Cables......................................................................................................................................29
1.8.1 Console Port Cables....................................................................................................29
1.8.2 Ethernet Port Cables....................................................................................................29
1.8.3 Optical Fibers...............................................................................................................29
1.8.4 E1 Cables.....................................................................................................................30
1.8.5 Antenna........................................................................................................................32
2 Preparing for Installation..................................................................................................................34
2.1 Safety Precautions...................................................................................................................34
2.1.1 General Safety Precautions.........................................................................................34
2.1.2 Movement ....................................................................................................................34
2.1.3 Electricity......................................................................................................................34
2.1.4 ESD..............................................................................................................................35
2.1.5 Laser............................................................................................................................35
2.1.6 Storage.........................................................................................................................36
2.2 Installation Site Requirements.................................................................................................36
2.2.1 Bearing.........................................................................................................................36
2.2.2 Ventilation.....................................................................................................................36
2.2.3 Space...........................................................................................................................36
2.2.4 Temperature and Humidity...........................................................................................36
2.2.5 Cleanliness...................................................................................................................37
2.2.6 Grounding ....................................................................................................................38
2.2.7 Anti-interference...........................................................................................................38
2.2.8 Surge Protection..........................................................................................................38

iii
2.2.9 Others ..........................................................................................................................38
2.3 Cabinet Installation Requirements...........................................................................................39
2.4 Tools ........................................................................................................................................40
3 Installing the Device.........................................................................................................................40
3.1 Installation Procedure..............................................................................................................41
3.2 Installation Preparation............................................................................................................41
3.3 Fixing the Device Location.......................................................................................................42
3.3.1 Installing the Device in a Cabinet................................................................................42
3.3.2 Installing the Device on a Workbench.........................................................................42
3.4 Installing a Power Module........................................................................................................42
3.4.1 Installing a Power Module............................................................................................43
3.4.2 Removing a Power Module..........................................................................................43
3.4.3 Installing Power Cords and Grounding Cables ...........................................................44
3.4.4 Removing Power Cords and Grounding Cables .........................................................44
3.5 Installing Service Modules.......................................................................................................45
3.5.1 Installing a Service Module..........................................................................................45
3.5.2 Removing a Service Module........................................................................................45
3.5.3 Troubleshooting ...........................................................................................................46
3.6 Verifying Installation.................................................................................................................46
4 Verifying the Operating Status.........................................................................................................47
4.1 Setting Up the Configuration Environment..............................................................................47
4.2 Powering On the Device..........................................................................................................47
4.2.1 Checklist Before Power-on..........................................................................................47
4.2.2 Device Power-on..........................................................................................................48

iv
4.2.3 Checklist After Power-on .............................................................................................48
5 Monitoring and Maintenance............................................................................................................49
5.1 Monitoring Devices Through CLI Commands .........................................................................49
5.2 Hardware Maintenance............................................................................................................49
5.2.1 Line Cards....................................................................................................................49
5.2.2 Power Modules............................................................................................................49
5.2.3 Expansion Modules......................................................................................................49
5.2.4 Heat Dissipation System..............................................................................................49
6 Troubleshooting................................................................................................................................50
6.1 Configuration System Troubleshooting...................................................................................50
7 Appendix...........................................................................................................................................51
7.1 Self-made Cable Connection Modes.......................................................................................51
7.2 Labeling Process.....................................................................................................................53
7.2.1 Manual Writing of Labels.............................................................................................53
7.2.2 Pasting Labels .............................................................................................................53
7.2.3 Label Contents.............................................................................................................54
7.3 Cabling.....................................................................................................................................55
7.4 Equipment Room Selection.....................................................................................................58

Hardware Installation and Reference Guide
1
1 Product Overview
1.1 Introduction to RG-RSR20-XA Series
RG-RSR20-XA series multi-service routers are centralized devices with high-performance processing and high-density
access capabilities. It supports the Border Gateway Protocol (BGP), IP multicast protocols, and rich QoS features, provides
power modules in redundancy mode, and allows users to configure optional modules. They can function as access layer
routers on large-scale industry networks. The RG-RSR20-XA series routers come into the RG-RSR20-XA-24, RG-RSR20-
XA-36, and RG-RSR20-XA-54.
1.2 RG-RSR20-XA-24
1.2.1 Package Contents
Table 1-1 Package Contents
No.
Item
Quantity
1
Chassis
1
2
Fixed bracket
2
3
Footbed
4
4
Fixed bracket installation instruction
1
5
Warranty card and list of hazardous
substances
1
6
M4X8 Phillips countersunk screw GB819-85
8
7
Yellow/Green ground cable
1
8
Access device management software of
Ruijie Networks
1
Note
The product management software is pre-installed in the device.

Hardware Installation and Reference Guide
2
1.2.2 Product Appearance
1. Front Panel
Figure 1-1 Front Panel
Table 1-2 Ports, LEDs, and Buttons on the Front Panel
No.
Item
Description
1
LED of the
10/100/1000Base-T
Ethernet port in auto-
negotiation mode
Solid yellow: A link is set up on the port at a rate of 10/100 Mbps.
Blinking yellow: A link is set up on the port at a rate of 10/100
Mbps and data is transmitted on the link.
Solid green: A link is set up on the port at a rate of 1000 Mbps.
Blinking green: A link is set up on the port at a rate of 1000 Mbps
and data is transmitted on the link.
Off: No link is set up on the port.
2
10/100/1000Base-T
Ethernet port in auto-
negotiation mode
The electrical port uses the RJ45 connector.
3
LED of the Layer 3
10/100/1000Base-T
Ethernet port in auto-
negotiation mode
Solid yellow: A link is set up on the port at a rate of 10/100 Mbps.
Blinking yellow: A link is set up on the port at a rate of 10/100
Mbps and data is transmitted on the link.
Solid green: A link is set up on the port at a rate of 1000 Mbps.
Blinking green: A link is set up on the port at a rate of 1000 Mbps
and data is transmitted on the link.
Off: No link is set up on the port.
4
Layer 3
10/100/1000Base-T
Ethernet port in auto-
negotiation mode
The electrical port uses the RJ45 connector.
5
SFP optical port LED
Solid green: A link is set up on the port at a rate of 1000 Mbps.
Blinking green: A link is set up on the port and data is transmitted
on the link.
Off: No link is set up on the port.
6
SFP optical port
For more information on applicable optical modules, see Pluggable
Modules.

Hardware Installation and Reference Guide
3
No.
Item
Description
7
SFP+ optical port LED
Solid green: A link is set up on the port.
Blinking green: A link is set up on the port and data is transmitted
on the link.
Off: No link is set up on the port.
8
SFP+ optical port
For more information about applicable optical modules, see Pluggable
Modules.
9
Console port
It is connected to the console for onsite configuration.
10
USB 2.0 port
It supports the FAT32 file format and connects to a USB flash drive.
Non-USB 2.0 devices are not supported. This port allows you to read
the configuration from the storage device or save the configuration to
the storage device.
11
FUNC button
After the FUNC button is pressed, the system will reset and restart
according to the original software version.
12
USB port LED
Solid green: The USB flash drive works properly.
Solid red: The USB flash drive encounters an exception.
Off: The USB flash drive is not installed.
13
System LED
System status LED
Solid green: The system works properly.
Blinking green: The system is starting up.
Solid red: A fault occurs in the system.
Off: The system not powered on, or is powered on but does not
work properly.
Power LED
PWR0 and PWR1, operating power status LEDs
Solid green: The power output is normal.
Solid red: The power output is abnormal.
Off: The system has no power supply.
The product nameplate is located on the bottom right corner of the device, as shown in Figure 1-2.

Hardware Installation and Reference Guide
4
Figure 1-2 Location of the Nameplate
2. Rear Panel
Figure 1-3 Rear Panel

Hardware Installation and Reference Guide
5
Table 1-3 Description of the Rear Panel
No.
Module Slot
and Grounding
Stud
Description
1
Slot 2
HSIC service module slot 2
2
Slot 4
HSIC service module slot 4
3
Slot 5
HSIC service module slot 5
4
Grounding stud
Protection against lightning strikes and interference
5
PWR0
Power module slot 0: Install the power module first and then connect the AC
power cord.
Power modules can work in 1+1 redundancy mode.
6
PWR1
Power module slot 1: Install the power module first and then connect the AC
power cord.
Power modules can work in 1+1 redundancy mode.
7
Slot 3
Service module slot 3: It is reserved for another module but not the HSIC
service module.
Note
If you cannot determine the number of the slot where the module is located, run the show version slot
command in privileged EXEC mode of the device to view the slot number of the module (not the power
module) and run the show env powers command to view the slot number of the power module.

Hardware Installation and Reference Guide
6
1.2.3 Technical Specifications
Table 1-4 Technical Specifications of the RG-RSR20-XA-24

Hardware Installation and Reference Guide
7
Model
RG-RSR20-XA-24
CPU
4GB DDR4
Flash Memory
8GB eMMC
10/100/1000Base-T
Ethernet Port in Auto-
Negotiation Mode
12 (1/0–1/11)
Layer 3 10/100/1000Base-
T Ethernet Port in Auto-
negotiation Mode
4 (0/0–0/3)
SFP+ Optical Port
4 (8F–11F)
SFP Optical Port
4 (4F–7F)
Service Module Slot
Four slots, and HSIC service modules supported
Console Port
1
USB Port
One USB 2.0 port
Port LED
24
System LED
4 (SYS, PWR0, PWR1, and FAN)
Number of Power Slots
2
Power Module
RG-PA150IB-F: input voltage: 100 V AC to 240 VAC, 50 Hz to 60 Hz;
maximum power: 150 W
Power Redundancy
Supported
Hot Swapping
Supported (the power module and HSIC-2E1/CE1 service module support hot
swapping)
Voltage
100 V AC to 240 V AC, 50 Hz to 60 Hz
Power Consumption
< 150 W
Dimensions (W x D x H)
440 mm x 420 mm x 44 mm (17.21 in. x 16.17 in. x 1.47 in.)
Weight
< 7.8 kg (17.19 lbs., full configuration without packaging materials)
Temperature
Operating temperature: 0ºC to 50ºC (32ºF to 122ºF)
Storage temperature: –40ºC to +70ºC (–40ºF to +158ºF)
Humidity
Operating humidity: 10% to 90% RH (non-condensing)
Storage humidity: 5% to 95% RH (non-condensing)

Hardware Installation and Reference Guide
8
Warning
In a domestic environment, this product may cause radio interference in which case the user may be required
to take adequate measures.
1.3 RG-RSR20-XA-36
1.3.1 Package Contents
Table 1-5 Package Contents
No.
Item
Quantity
1
Chassis
1
2
Fixed bracket
2
3
Footbed
4
4
Fixed bracket installation instruction
1
5
Warranty card and list of hazardous
substances
1
6
M4X8 Phillips countersunk screw GB819-
85
8
7
Yellow/Green ground cable
1
8
Access device management software of
Ruijie Networks
1
Note
The product management software is pre-installed in the device.

Hardware Installation and Reference Guide
9
1.3.2 Product Appearance
1. Front Panel
Figure 1-4 Front Panel
Table 1-6 Ports, LEDs, and Buttons on the Front Panel
No.
Item
Description
1
LED of the
10/100/1000Base-T
Ethernet port in auto-
negotiation mode
Solid yellow: A link is set up on the port at a rate of 10/100 Mbps.
Blinking yellow: A link is set up on the port at a rate of 10/100
Mbps and data is transmitted on the link.
Solid green: A link is set up on the port at a rate of 1000 Mbps.
Blinking green: A link is set up on the port at a rate of 1000 Mbps
and data is transmitted on the link.
Off: No link is set up on the port.
2
10/100/1000Base-T
Ethernet Port in Auto-
Negotiation Mode
The electrical port uses the RJ45 connector.
3
LED of the Layer 3
10/100/1000Base-T
Ethernet port in auto-
negotiation mode
Solid yellow: A link is set up on the port at a rate of 10/100 Mbps.
Blinking yellow: A link is set up on the port at a rate of 10/100
Mbps and data is transmitted on the link.
Solid green: A link is set up on the port at a rate of 1000 Mbps.
Blinking green: A link is set up on the port at a rate of 1000 Mbps
and data is transmitted on the link.
Off: No link is set up on the port.
4
Layer 3
10/100/1000Base-T
Ethernet port in auto-
negotiation mode
The electrical port uses the RJ45 connector.
5
SFP optical port LED
Solid green: A link is set up on the port.
Blinking green: A link is set up on the port and data is transmitted
on the link.
Off: No link is set up on the port.
6
SFP optical port
For more information on applicable optical modules, see Pluggable
Modules.

Hardware Installation and Reference Guide
10
No.
Item
Description
7
SFP+ optical port LED
Solid green: A link is set up on the port.
Blinking green: A link is set up on the port and data is transmitted
on the link.
Off: No link is set up on the port.
8
SFP+ optical port
For more information on applicable optical modules, see Pluggable
Modules.
9
Console port
It is connected to the console for onsite configuration.
10
USB 2.0 port
It supports the FAT32 file format and connects to a USB flash drive.
Non-USB 2.0 devices are not supported. This port allows you to read
the configuration from the storage device or save the configuration to
the storage device.
11
FUNC button
After the FUNC button is pressed, the system will reset and restart
according to the original software version.
12
USB port LED
Solid green: The USB flash drive works properly.
Solid red: The USB flash drive encounters an exception.
Off: The USB flash drive is not installed.
13
System LED
System status:
Solid green: The system works properly.
Blinking green: The system is starting up.
Solid red: A fault occurs in the system.
Off: The system not powered on, or is powered on but does not
work properly.
Power LED
Power status:
Solid green: The power output is normal.
Solid red: The power output is abnormal.
Off: The system has no power supply.
Fan module LED
Fan module status:
Green: The fan module works properly.
Red: Fan abnormal
Off: Device hardware is abnormal or the device is not powered on.
The product nameplate is located on the bottom right corner of the device, as shown in Figure 1-5.

Hardware Installation and Reference Guide
11
Figure 1-5 Location of the Nameplate
2. Rear Panel
Figure 1-6 Rear Panel

Hardware Installation and Reference Guide
12
Table 1-7 Description of the Rear Panel
No.
Module Slot
and Grounding
Stud
Description
1
Slot 2
HSIC service module slot 2
2
Slot 4
HSIC service module slot 4
3
Slot 5
HSIC service module slot 5
4
Grounding stud
Protection against lightning strikes and interference
5
PWR0
Power module slot 0: Install the power module first and then connect the AC
power cord.
Power modules can work in 1+1 redundancy mode.
6
PWR1
Power module slot 1: Install the power module first and then connect the AC
power cord.
Power modules can work in 1+1 redundancy mode.
7
Slot 3
Service module slot 3: It is reserved for another module but not the HSIC
service module.
Note
If you cannot determine the number of the slot where the module is located, run the show version slot
command in privileged EXEC mode of the device to view the slot number of the module (not the power
module) and run the show env powers command to view the slot number of the power module.