Ruijie RG-S6510-4C Series Installation and operating manual

Ruijie RG-S6510-4C Series Switches
Hardware Installation and Reference Guide

Copyright Statement
Ruijie Networks©2021
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our switches. This guide will help you install and use the switches.
Scope
This manual describes the functions and physical features of the switches, and presents the installation procedure,
troubleshooting procedure, technical specifications, and specifications and usages rules of cables and connectors. It is
intended for the users that have some experience in installing and maintaining network hardware and want to learn the
above information. At the same time, it is assumed that the users of this switch are already familiar with the related
terms and concepts of Ethernet.
Document Structure
Chapter 1 "Product Overview" describes the main characteristics, technical specifications, and related modules
of this product.
Chapter 2 "Preparation before Installation" lists the safety, power supply, and site requirements that must be
met before the switch can be installed.
Chapter 3 "Product Installation" describes how to install the integrated switch and modules, and connect its
power cables and grounding lines.
Chapter 4 "System Debugging" describes the commissioning after the switch is powered on for the first time.
Chapter 5 “Monitoring and Maintenance”
Chapter 5 "Troubleshooting" describes possible problems met during the installation and use of the switch and
solutions for such problems.
Appendix A "Connector and Connection Media"
Appendix B "Mini-GBIC, 10G, 40G Modules and FC Modules"
Appendix C “Lightening Protection”
Appendix D “Cabling Recommendations in Installation”
Appendix E “Site Selection”
Appendix F “Mini USB Console Driver Installation”
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [email protected]
Skype: [email protected]
Related Documents

Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss
of data.

RG-SS6510-4C Series Switch Hardware Installation and Reference Guide Product Overview
- 3 -
1 Product Overview
RG-S6510-4C series switch is a data center-oriented high-density 10G layer 3 IPv6 box-type switch. They are mainly
applicable to data center scenario to provide convergence and access service for the servers with 10G ports.
The RG-S6510-4C series switch includes a switch and three extension modules.
Model
100G/40G
QSFP28
Ethernet Port
25G/10G
SFP28
Ethernet Port
10GBase-T
Ethernet Port
Extension
Module Slot
Redundant
Fan
Redundant
Power Supply
RG-S6510-4C
-
-
-
4
2+1
1+1
M6500-24VS2CQ
2
24
-
-
-
-
M6500-08CQ
8
-
-
-
-
-
M6500-16QXS
16
An SFP28 port supports 25G/10Gbase-R and does not support 1000base-X.
A QSFP28 port supports both 100G/40G mode and 4x25G/4x10G mode.
1.1 RG-S6510-4C
Specifications
Model
RG-S6510-4C
CPU
Quad-core processer, 1.0GHz
BOOT ROM
8MB
EMMC
8GB
SDRAM
DDR3 4GB
Extension Module
Slot
4
Extension Module
M6500-24VS2CQ, M6500-08CQ, M6500-16QXS
Fan Slot
3 (support 2+1 redundancy, configure at least 2 fan modules in one switch)
Fan Module
M6500-FAN-F
Power Supply
Slot
2 (support 1+1 redundancy)
Power Module
RG-PA800I-F
Power Supply
Input
AC input
Rated voltage range: 100V AC to 240V AC
Maximum voltage range: 90V AC to 264V AC
Frequency: 50 Hz to 60 Hz
Rated current: 10 A to 5 A
High voltage direct current (HVDC) input:
Input voltage range: 192V DC to 288V DC
Rated input current: 240V DC
Input current range: <4.5 A
Power
Consumption
Less than 650 W

RG-SS6510-4C Series Switch Hardware Installation and Reference Guide Product Overview
- 4 -
Fiber Module
Refer to Appendix B
The supported modules may change. Please contact Ruijie Networks for details.
SFP28 Port
Supported. The number of ports depends on the extension module.
QSFP28 Port
Supported. The number of ports depends on the extension module.
10GBASE-T Port
Unsupported
Temperature
Warning
Support temperature warning and over-temperature protection.
EMC Standards
GB9254-2008 CLASS A
Safety Standards
GB4943-2011
Working
Temperature
0°C to 40°C (32°F to 104°F)
Storage
Temperature
-40°C to 70°C (-40°F to 158°F)
Working Humidity
10% to 90% RH (non-condensing)
Weight（with 3 fan
modules and 2
power modules）
19 kg (41.89 lbs)
Dimensions
(L x W x H)
442 mm x 520 mm x 86 mm (17.40 in. x 20.47 in. x 3.39 in.), 2RU
RG-S6510-4C switch is a class A product. In a domestic environment, this product may cause radio interference in
which case the user may be required to take adequate measures.
Product Appearance
The hardware of the S6510-4C includes the chassis, the power supply system and the heat dissipation system.
The power supply system: Provides 2 power supply slots, which support 1+1 power supply redundancy. It is
recommended users configure power supply redundancy.
The heat dissipation system: Provides 3 fan module slots, which support 2+1 fan redundancy. It is recommended
users configure all fans redundancy.
Figure 1-1 Appearance of the RG-S6510-4C

RG-SS6510-4C Series Switch Hardware Installation and Reference Guide Product Overview
- 5 -
Front Panel
Figure 1-2 Front Panel of the S6510-4C
Notes:
1. Sub Slot 1
2. Sub Slot 2
3. Sub Slot 3
4. Sub Slot 4
Back Panel
Figure 1-3 Back Panel of the S6510-4C
Notes:
1. Fan Module Slot
2. Fan Indicator
3. USB Port
4. MGMT Port
5. Console Port
6. Mini-USB Serial Port
7. MGMT Status Indicator
8. ID Indicator
9. Status Indicator
10. Reserved Function Button
11. Asset Management Label
12. Grounding Point
13. Power Slot
Asset Management Label
The asset management label is next to the switch status indicator of the switch back panel. The label is movable and
can be withdrawn from the device. Users can mark the information such as asset name, category, code and registration
date on the label which helps to improve asset management accuracy and efficiency.
Figure 1-4 Asset Management Label of the RG-S6510-4C

RG-SS6510-4C Series Switch Hardware Installation and Reference Guide Product Overview
- 6 -
External Ports
The RG-S6510-4C provides the following ports:
Universal serial bus (USB) port: This port can connect with USB memory to save logs, host versions, warnings
and other diagnostic messages. Therefore, it is more convenient to upgrade the software version of the switch on
line and save the log information.
To protect the data and avoid device damage, use qualified USB flash disks of good brands. At the same time, the
local USB port is compatible with most of the USB controllers except some USB flash disks.
Console port: Use RS-232 interface electrical level and standard RJ45 connector. This interface is connected with
the serial port of terminal PC to perform system debugging, configuration, maintenance, management, and host
software uploading.
Mini-USB serial port: Use mini-USB cable to connect the USB port. This interface is connected with the serial port
of terminal PC to perform system debugging, configuration, maintenance, management, and host software
uploading.
10/100/1000M MGMT port: This is an out-band Ethernet port, which uses standard RJ45 connector. This interface
is connected with Ethernet port of a PC to perform program downloading.
Indicator
Indicator
Panel
Identification
Status
Meaning
System indicator
Status
Off
The system is not powered up.
Solid red
1) One of the modules fails.
2) The internal temperature exceeds the threshold,
and the switching service resets.
Blinking green
The system is initializing.
Solid green
The system is operational.
Solid yellow
The temperature exceeds the threshold.
ID indicator
ID
Off
Device location is disabled.

RG-SS6510-4C Series Switch Hardware Installation and Reference Guide Product Overview
- 7 -
Solid blue
Device location is enabled.
MGMT port indicator
MGMT
Off
The port is not connected.
Green
The port is connected at 1000Mbps.
Yellow
The port is connected at 10/100Mbps.
Blinking
The port is transmitting or receiving data.
Power Supply
The RG-S6510-4C series switch supports power supply the PA800I-F. The smart power supply module supports power
management, and the host can read input power, input current, and temperature in real time. The power supply module
supports hot swapping.
The RG-S6510-4C series switch supports 1+1 power supply redundancy. To improve the stability and reliability of
the entire system, it is recommended to configure 1+1 power supply redundancy. When the two power supply
modules work normally, the switch is in the status of current sharing.
It requires at least one power supply module to work normally. Install a blank panel to the empty slot to prevent
dust from entering the switch.
Heat Dissipation
The working temperature of the RG-S6510-4C switch is 0°C to 40°C (32°F to 104°F), and the heat dissipation design
needs to ensure the stability, safety and maintainability in such environment. The RG-S6510-4C series switch adopts
fan ventilation and forced convection to ensure the device can work normally in specified environment. Dust the device
every three months to avoid blocking the ventilation openings.
The RG-S6510-4C supports M6500-FAN-F and provides fan speed regulation, fan failure warning, and fan hot
swapping.
Figure 1-5 Ventilation and Heat Dissipation of the RG-S6510-4C
Maintain a minimum of 20 cm clearance around the device for ventilation.
It requires at least two fan modules to work normally. Install a blank panel to the empty slot to prevent dust from
entering the switch.

RG-SS6510-4C Series Switch Hardware Installation and Reference Guide Product Overview
- 8 -
1.2 Modules
RG-S6510-4C switch supports the following modules: M6500-24VS2CQ, M6500-08CQ, M6500-16QXS, RG-PA800I-F,
and M6500-FAN-F.
1.2.1 M6500-24VS2CQ
Module Appearance
Figure 1-6 M6500-24VS2CQ
Notes:
1. Status Indicator
2. 25G/10G SFP28 Port
3. 1F-24F Port Status Indicator
4. 25F-26F Port Status Indicator
5. 100G/40G QSFP28 Port
External Ports
The M6500-24VS2CQ provides 24 SFP28 ports and 2 QSFP28 ports and supports hot swapping of SFP28/SFP+ and
QSFP28/QSFP+ modules. Both fiber modules and DAC can be used.
Indicator
Indicator
Panel
Identification
Status
Meaning
System indicator
Status
Off
The system is not powered up.
Solid red
The module fails or resets.
Blinking green
The system is initializing.
Solid green
The system is operational.
Solid yellow
The temperature exceeds the threshold.
SFP28 port indicator
1F-24F
Off
The port is down.
Solid green
The port is up.
Blinking
The port is receiving or transmitting data.
QSFP28 port
indicator
25F-26F
(4*25G/4*10G)
Off
The port is down.
Solid green
The port is connected at 25G/10G.
Blinking green
The port is receiving or transmitting data at 25G/10G.
25F-26F
(1*100G/1*40G)
Off
The port is down.
Solid green
The port is connected at 100G/40G.