Ruijie Reyee RG-RAP2260 Installation and operating manual

Ruijie Reyee RG-RAP2260(E) Access Point
Hardware Installation and Reference Guide

·
Copyright statement
Ruijie Networks©2021
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,
modification, transmission, translation or commercial use of this document or any portion of this document,
in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.
Exemption statement
This document is provided “as is”. The contents of this document are subject to change without any notice.
Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to
ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to
content omissions, inaccuracies or errors.

·
Preface
Thank you for using our products. This manual will guide you through the installation of the access point.
Scope
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [e-mail]
Skype: [e-mail]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Documentation Conventions
The symbols used in this document are described as below:
This symbol brings your attention to some helpful suggestions and references.
This symbol means that you must be extremely careful not to do some things that may damage the device or cause
data loss.

·
Hardware Installation and Reference Guide Product Overview
1 Product Overview
Featuring leading 802.11a/b/g/n/ac/ax and MU-MIMO, Ruijie RG-RAP2260(E) supports 4 spatial streams and delivers up
to 800Mbps at 2.4G and 2400Mbps at 5G. The overall dual-band performance speeds up to 3200Mbps per device, totally
eliminating Gigabit wireless bottlenecks. RG-RAP2260(E) adopts either local power supply or PoE power supply, and
provides two Ethernet ports, making it possible connect a camera or switch device to adapt to challenges in a wide variety
of deployment scenarios.
1.1 Technical Specifications
Table 1-1 RG-RAP2260(E) Technical Specifications
Model
RG-RAP2260(E)
RF
Four-stream and dual-band
Transmission
Protocol
Support concurrent 802.11ax, 802.11ac wave2/wave1, 802.11a/b/g/n
Operating Bands
802.11b/g/n: 2.4 GHz to 2.4835 GHz
802.11a/n/ac/ax: 5.150 GHz to 5.250 GHz, 5.250 GHz to 5.350 GHz, 5.470 GHz to 5.725 GHz,
5.725 GHz to 5.850 GHz (Country-specific)
Antenna
Array antenna (2.4G: 3dBi, 5G: 3dBi)
Spatial Streams
2.4G: 4 x 4 MIMO
5G: 4 x 4 MIMO
Max Throughput
2.4G: up to 800 Mbps
5G: up to 2400 Mbps
Up to 3200 Mbps per AP
Modulation
OFDM: BPSK@6/9Mbps, QPSK@12/18Mbps, 16QAM@24Mbps, 64QAM@48/54Mbps
DSSS: DBPSK@1Mbps, DQPSK@2Mbps, and CCK@5.5/11Mbps
MIMO-OFDM: BPSK, QPSK, 16QAM , 64QAM, 256QAM and1024QAM
OFDMA
Receive Sensitivity
11b: -91dBm(1Mbps), -90dBm(5Mbps), -87dBm(11Mbps)
11a/g: -89dBm(6Mbps), -82dBm(24Mbps), -78dBm(36Mbps), -72dBm(54Mbps) 11n:
-85dBm(MCS0), -67dBm(MCS7)
11ac: 20MHz: -85dBm(MCS0), -60dBm(MCS9)
11ac: 40MHz: -82dBm(MCS0), -57dBm(MCS9)
11ac: 80MHz: -79dBm(MCS0), -53dBm(MCS9)
11ax: 80MHz: -79dBm(MCS0), -53dBm(MCS9),-52dBm(MCS11)
Transmit Power
≤100mw(20dBm) (adjustable)
Transmit Power
Adjustment
1 dBm
Dimensions
(W x D x H)
220 mm x 220 mm x 35 mm (8.7 in. x 8.7 in. x 1.4 in.) (excluding brackets)
Weight
≤1.05 kg (excluding brackets)
Service Ports
One 10/100/1000BASE-T Ethernet uplink port, one 10/100/2500BASE-T Ethernet uplink port,

·
Hardware Installation and Reference Guide Product Overview
LAN1/2.5G/PoE port is PoE+-capable
Management Ports
N/A
LED
1 LED (green)
Power Supply
Adapter: DC 12 V/2.5 A (optional)
PoE: IEEE 802.3at-compliant (PoE+).
Power Consumption
< 25.4W
Temperature
Operating: 0°C to 40°C (32°F to 104°F)
Storage: –40°C to 70°C (–40°F to 158°F)
Humidity
Operating: 5% to 95% RH (non-condensing)
Storage: 5% to 95% RH (non-condensing)
Installation
Ceiling/wall mount
Safety Standards
GB4943
IEC60950-1
EMC Standards
GB9254
EN301 489
EN50155
EN50121
Mechanical
Vibration
IEC61373
Radio
China Radio Transmission Equipment Type Approval Certificate
EN300 328
EN301 893
MTBF
> 400,000 H
Weight refers to the weight of host.
1.2 Product Image
The AP provides two Ethernet ports (LAN1/2.5G/PoE port is PoE+-capable), and one power port for an external power
supply.
Figure 1-1 Appearance of RG-RAP2260(E)

·
Hardware Installation and Reference Guide Product Overview
1.3 LED Indicator and Button
LED Indicator
and Button
State
Frequency
Meaning
LED Indicator
Off
N/A
The AP is NOT receiving power.
Blinking
0.5Hz
Normal operation, but there is an alarm.
Fast blinking
10Hz
Possible cases:
1. Restoring the factory default settings
2. Upgrading the firmware
3. Restoring the image file
4. Initializing the device
Solid green
N/A
Normal operation.
Reset Button
Press for less than 2 seconds
Restart the device.
Press for more than 5 seconds
Restore the factory settings.
1.4 Power Sources
The AP can be powered either with a power adapter or through Power over Ethernet (PoE).
The power adapter is customer-supplied.
To use a PoE device, make sure that it supports the IEEE 802.3at standard.
1.5 Cooling Solution
The AP features a fanless design.
Leave sufficient space surrounding the AP when installing the AP to permit proper airflow for ventilation.

·
Hardware Installation and Reference Guide Preparing for Installation
2 Preparing for Installation
To prevent device damage and physical injury, please read the safety recommendations carefully as described in this
chapter.
Recommendations do not cover all possible hazardous situations.
2.1 Installation
The AP must be installed indoors. To ensure normal operation, the installation site must meet the following requirements.
Install the AP in a well-ventilated environment. If it is installed in a closed room, make sure there is a good cooling
system.
Make sure the site is sturdy enough to support the AP and its accessories.
Make sure the site has enough space for installing the AP and leave sufficient room around the AP for ventilation.
Do not expose the AP to high temperature, dust, or harmful gases.
Do not install the AP in an area prone to fire or explosions.
Keep the AP away from EMI sources such as large radar stations, radio stations, and substations.
Do not subject the AP to unstable voltage, vibration, and noises.
Keep the AP at least 500 meters away from the ocean and do not face it towards the sea breeze.
The installation site should be free from water including possible flooding, seepage, dripping, or condensation.
The installation site should be selected according to network planning and communications equipment features, and
considerations such as climate, hydrology, geology, earthquake, electrical power, and transportation.
Please follow the correct method described in the installation guide to install and remove the device.
2.2 Movement
Avoid frequently moving the device.
Turn off all power supplies and unplug all power cables before you remove the device.
2.3 EMI
Please observe local regulations and specifications when performing electrical operations. Relevant operators must
be qualified.
Carefully check for any potential hazards in the working area such as damp/wet ground or floors.
Find the location of the emergency power supply switch in the room before installation. Cut off the power supply first
in case of an accident.
Be sure to make a careful check before shutting down the power supply.

·
Hardware Installation and Reference Guide Preparing for Installation
Do not place the device in a damp/wet location. Do not let any liquid enter the chassis.
Keep the AP far away from grounding or lightning protection devices for power equipment.
Keep the AP away from radio stations, radar stations, high-frequency high-current devices, and microwave ovens.
Any nonstandard and inaccurate electrical operation can cause an accident such as fire or electric shock, thus
causing severe even fatal damages to humans and devices.
Direct or indirect contact with a wet object (or your finger) on the high voltage and power line can be fatal.
2.4 Ventilation
For proper ventilation, leave sufficient space around the AP.
2.5 Temperature and Humidity
To ensure the normal operation and equipment service life, maintain appropriate temperature and humidity levels in the
equipment room. See Table 2-1. Improper room temperature and humidity can cause damage to the device.
High relative humidity may affect insulation materials, resulting in poor insulation and even electrical leakage.
Sometimes it may lead to changes in the mechanical properties of materials and corrosion of metal parts.
Low relative humidity can dry and shrink insulation sheets and cause static electricity that can damage the circuitry.
High temperatures greatly reduce device reliability and shorten service life.
Table 2-1 Required Temperature and Humidity for the RG-RAP2260(E)
Temperature
Relative Humidity
0ºC to 40ºC (32°F to 104°F)
5% to 95%
2.6 Cleanness
Dust poses a serious threat to device operation. Dust on the surface of the device can be absorbed onto metal contact
points by static electricity causing poor contact. Electrostatic absorption of dust occurs more easily when the relative
humidity is low, and might shorten the equipment service life and cause communication failures. Table 2-2 shows the
maximum concentration and diameter of dust allowed in the equipment room.
Table 2-2
Maximum diameter (μm)
0.5
1
3
5
Maximum concentration
(Particles/m3)
1.4×107
7×105
2.4×105
1.3×105
The amount of salt, acids and sulfides in the air are also strictly limited for the equipment room. These substances can
accelerate metal corrosion and aging of some parts. Table 2-3 describes the limits of some hazardous gases such as SO2,
H2S, NO2and Cl2 in the equipment room.
Table 2-3
Gas
Average (mg/m3)
Maximum (mg/m3)

·
Hardware Installation and Reference Guide Preparing for Installation
SO2
0.2
1.5
H2S
0.006
0.03
NO2
0.04
0.15
NH3
0.05
0.15
Cl2
0.01
0.3
2.7 Power Supply
DC power adapter:
Input voltage: 12V
Rated current: 2.5A
PoE+ injector: IEEE 802.3at compliant
Technical Specifications of the DC Connector
Inner Diameter
Outer Diameter
Insertion
Depth
Conductor
Impedance
Voltage-endu
rance
Impedance
Voltage-endu
rance
(Insulator and
Conductor)
Polarity
2.10+/-0.05mm
5.50+/-0.05mm
9mm
5Ω
100MΩ
1000V
Inner pole:
positive
Outer pole:
negative
The DC input power should be greater than the power actually consumed by the system.
Use DC power adapters with specifications recommended by Ruijie.
Please use Ruijie certified PoE injectors.
Warning：802.3af or non-standard POE adapter may cause unknown issues. Please use Ruijie POE+ switch or
802.3at POE adapter as power supplier
2.8 Installation Tools
Common Tools
Phillips (crosshead) screwdriver, copper and fiber cables, bolts, diagonal pliers, cable ties
Special Tools
Wire stripper, crimping pliers, RJ-45 crimping pliers, punch down tool
Meter
Multimeter, bit error rate tester (BERT)
The tools listed above are customer supplied.
2.9 Unpacking the Access Point
Package Contents

·
Hardware Installation and Reference Guide Preparing for Installation
Items
Verify that all parts are installed and debugged.
Screws
Mounting brackets
Product quick installation guide
Packing list
The above listed items are for general situations, and contents mayvary in the actual shipment. The purchasing order
shall prevail in any case. Please check each item carefully according to the packing list or purchasing order. If any
item is damaged ormissing, notify your sales representative.