Ruijie RG-AP630 Directional User manual

Ruijie RG-AP630 (CD) Wireless Access Points
Quick Installation Guide

Copyright Statement
Ruijie Networks©2019
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [email protected]
Skype: [email protected]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of
data.

RG-AP630(CD) Wireless Access Point Quick Installation Guide
1Packing List
Name
Quantity
Unit
Host
1
Set
Mounting plate
1
Piece
Mounting bracket
1
Piece
Tie rod
1
Piece
M8x20 screw with spring and flat washers
4
Piece
M8x40 screw with spring and flat washers
2
Piece
Liquid-tight adapter
1
Piece
Liquid-tight adapter for optical fiber (Hardware Version
2.00 and later)
1
Piece
Grounding cable
1
Piece
Hose clamp
2
Piece
Security cable
1
Piece
M8x60 expansion bolt
4
Piece
Product Warranty Manual
1
Copy
RG-AP630 (CD) Wireless Access Point Quick Installation
Guide
1
Copy
2Accessories
Mounting Plate Mounting Bracket Tie Rod M8X40/M8X20 Screw
Grounding Cable Hose Clamp Liquid-tight Adapter
Liquid-tight Adapter for Optical Fiber Security Cable M8x60 Expansion Bolt

RG-AP630(CD) Wireless Access Point Quick Installation Guide
3Product Appearance
Product Appearance of RG-AP630 (CD)
Note: 1. Console port 2. 10/100/1000 Base-T auto-sensing Ethernet/PoE IN port 3. SFP combo port

RG-AP630(CD) Wireless Access Point Quick Installation Guide
4Installation Tools
The tool kit is customer supplied.
5LEDs
LED
State
Meaning
Blinking green
Initialization in progress
Solid yellow
Initialization is complete, but no CAPWAP connection.
Solid green
Initialization is complete, and a CAPWAP connection is
established.
System status
Solid red
The Ethernet/PoE IN port is disconnected.
1 solid on
< -70dBm
2 solid on
-70 to -50 dBm
WDS RSSI (3 LEDs)
3 solid on
> -50 dBm

RG-AP630(CD) Wireless Access Point Quick Installation Guide
6Installing the Security Cable
Remove the security cable from the mounting plate first. Then, attach the mounting plate to the bottom of the AP and
fasten the plate with the four M8x20 screws. Note that one screw is used to fix the metal shim of End A onto the plate
before it is tightened.
Attach the tie rod to the mounting plate and fasten the rod with the M8x40 screws after AP is well-positioned, shown in the
following figure.

RG-AP630(CD) Wireless Access Point Quick Installation Guide
7Mounting the AP to the Pole
Attach the mounting bracket to a pole with a hose clamp.
Attach the mounting plate to the mounting bracket through the rod with the M8x40 screws, adjust AP orientation, and
tighten the screws on the rod with the Phillips screwdriver (or the wrench). Finally, connect Loop B of the security cable to
the bracket by fastening the screw attached to Loop B
Horizontal pole mount is also supported. The procedure of horizontal pole mount is similar as that of vertical mount.
The outdoor AP can be mounted on a wall and a pole (diameter: 75 mm to 120 mm). If the diameter of the pole is out
of the range, the hose clamp is customer-supplied. In this case, we strongly recommend you to use a 304 stainless
steel hose clamp with thickness of 2.5mm at least.
8Mounting the AP on the Wall
Attach the mounting bracket to the wall with user-supplied expansion screws. M8 x 60 screws are recommended.
Mark the locations of the four screw holes by using the marker. Drill four 8 mm diameter holes. Tap expansion anchors
into the holes, and drive three screws through the mounting bracket into the anchors to fix the bracket.

RG-AP630(CD) Wireless Access Point Quick Installation Guide
Attach the tie rod to the mounting plate and fix the rod with the supplied M8x40 screws. Adjust the AP orientation, and
drive the two-side screws on the rod. Finally, drive the screw of Loop B into the fourth anchor.
9Connecting the Fiber Cable
The liquid-tight adapter for optical fiber is supplied for hardware V2.00 and later
Waterproofing material is customer-supplied.
1) Choose an LC-LC optical fiber with the diameter of 2.7±0.2mm.
2) Thread the fiber through the liquid-tight adapter in the order as shown.

RG-AP630(CD) Wireless Access Point Quick Installation Guide
3) Insert the plug of the fiber into the SPF port.
4) Tighten A.
5) Combine B and C and put the combination into A.
6) Tighten D before applying waterproof glue to its joint with A.
Before removing the optical fiber, dismantle the liquid-tight adapter first and then the plug.
If the diameter of LC-LC fiber is not 2.7±0.2mm, waterproofness of the adapter cannot be guaranteed.
10 Connecting the Network Cable
Thread the original network cable through the liquid-tight adapter.
Attach the plug into one end of the network cable nearest to the head of the liquid-light adapter.
Insert the plug into the PoE IN port, and tighten the liquid-tight adapter.
Make sure the plug is correctly inserted. The plug gets damaged when the liquid-tight adapter is wrenched
improperly. Before removing the network cable, dismantle the liquid-tight adapter first and then the plug.
11 Connecting the Grounding Cable
Make sure the AP and the power source share the common ground points.
A lightning arrester is integrated into the AP. In general, no additional lightening arrester is required. If there is higher
requirement for lightening protection, you can purchase it on your own.