Ruijie Reyee RG-RAP6262 Series Installation and operating manual

Ruijie Reyee RG-RAP6262(G)
Series Access Points
Hardware Installation and Reference Guide V1.0
Document Version: V1.0
Date: 2022-02-18
Copyright © 2022 Ruijie Networks

Copyright
Ruijie Networks©2022
Ruijie Networks reserves all copyrights of this document.
Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this
document or any portion of this document, in any form or by any means, without the prior written consent of
Ruijie Networks is prohibited.
Trademarks including , and are
owned by Ruijie Networks.
All other trademarks or registered trademarks mentioned in this document are owned by their respective owners.
Disclaimer
The products, services or features you purchase are subject to commercial contracts and terms. Some or all of
the products, services or features described in this document may not be within the scope of your purchase or
use. Unless otherwise agreed in the contract, Ruijie Networks does not make any express or implied statement
or guarantee for the content of this document.
Due to product version upgrades or other reasons, the content of this document will be updated from time to
time. Ruijie Networks reserves the right to modify the content of the document without any notice or prompt.
This manual is for reference only. Ruijie Networks endeavors to ensure content accuracy and will not shoulder
any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Hardware Installation and Reference Guide 1 Product Overview
1
Preface
Intended Audience
This document is intended for:
Network engineers
Technical support and servicing engineers
Network administrators
Technical Support
The official website of Ruijie Reyee: https://www.ruijienetworks.com/products/reyee
Conventions
1. Signs
The symbols used in this document are described as follows:
Danger
An alert that calls attention to safety operation instructions that if not understood or followed when operating
the device can result in physical injury.
Warning
An alert that calls attention to important rules and information that if not understood or followed can result in
data loss or equipment damage.
Caution
An alert that calls attention to essential information that if not understood or followed can result in function
failure or performance degradation.
Note
An alert that contains additional or supplementary information that if not understood or followed will not lead to
serious consequences.
Specification
An alert that contains a description of product or version support.
2. Note
This manual provides the device installation steps, hardware troubleshooting, module technical specifications,
and specifications and usage guidelines for cables and connectors. It is intended for the users who have some
experience in installing and maintaining network hardware. At the same time, it is assumed that the users are
already familiar with the related terms and concepts.

Hardware Installation and Reference Guide 1 Product Overview
2
1 Product Overview
The RG-RAP6262(G) is an outdoor wireless access point (AP) designed by Ruijie Networks for high-speed
wireless networks. Adhering to the latest 802.11ax standard, the AP delivers an access rate of up to
1200Mbps@5G + [email protected]. RAP6262(G) features security, radio frequency (RF) control, mobile access,
Quality of Service (QoS) and seamless roaming. In addition, it can be managed by RG-WS series wireless
access controllers (ACs) to implement wireless data forwarding, security, and access control.
The IP68 design adapts to inclement outdoor environments such as the cold and humidity. This substantially
simplifies installation and maintenance. RAP6262(G) supports PoE to take over challenges in a wide variety of
deployment scenarios, including large-scaled campuses, enterprises, hospitals and Wi-Fi hotspots.
1.1 Technical Specifications
Table 1-1 Technical Specifications of RG-RAP6262(G)
Model
RG-RAP6262(G)
Dimensions (L x
W x H)
222 mm × 200 mm × 166 mm (8.74 in. x 7.87 in. x 6.54 in.)
Access Rate
Built-in antenna: 1775 Mbps
2.4 GHz: up to 575 Mbps
5 GHz: up to 1200 Mbps
Operating
Frequency
802.11b/g/n/ax: 2.4 GHz to 2.483 GHz
802.11a/n/ac/ax: 5.150 GHz to 5.350 GHz, 5.47 GHz to 5.725 GHz, 5.725 GHz to
5.850 GHz
(Country-Specific)
Maximum
Transmit Power
500 mW (Country-Specific)
Antenna Type
Built-in omnidirectional antenna
Antenna Gain
2.4 GHz: 3 dBi
5 GHz: 4 dBi
Beam Width
2.4G: E: 30°; H: 360°
5G: E: 30°; H: 360°
Ports
Two 10/100/1000 Base-T Ethernet ports
Uplink LAN 1/PoE port supports PoE
FIT/FAT Mode
Not supported
LED
System and port status indicators
Power Supply
12 V DC/2 A IEEE 802.3at (PoE+)

Hardware Installation and Reference Guide 1 Product Overview
3
Power
Consumption
Maximum: 17 W
Temperature
Operating: -30°C to 65°C (-22°F to 149°F)
Storage: -40°C to 85°C (-40°F to 185°F)
Humidity
Operating: 0% to 100% (non-condensing)
Storage: 0% to 100% (non-condensing)
IP Rating
IP68
Weight (Without
Bracket)
< 1 kg (2.20 lbs)
Safety
Standards
IEC62368-1
EMC Standards
EN55032
EN55035
EN301489-1
EN301489-17
Vibration
IEC61373
Radio
Approvals
EN300328
EN301893
EN62311
EN50385
EN62232
Table 1-2 LEDs of RG-RAP6262(G)
Indicator
Status
Meaning
Wi-Fi (Green)
Blinking
Data is transmitted by Wi-Fi.
Solid on
Wi-Fi is enabled and no data is transmitted.
Off
Wi-Fi is disabled.
SYS(Blue)
Blinking
Fast blinking: The device is being initialized.
Slow blinking (0.5 Hz): The device cannot access the Internet.
Blinking twice*:
1. Restoring the factory settings.
2. Upgrading the firmware.
3. Restoring the image file.
*In this case, please do not power off the device.
Solid on
The device is working properly.
Off
The device is powered off.
LAN 1(Green)
Blinking
The port is up and data is transmitted.

Hardware Installation and Reference Guide 1 Product Overview
4
Solid on
The port is up and no data is transmitted.
Off
The port is not connected.
LAN 2(Green)
Blinking
The port is up and data is transmitted.
Solid on
The port is up and no data is transmitted.
Off
The port is not connected.
Table 1-3 Reset Button
Button
Function
Operation
Reset
Reboot
Press the button for less than 2 seconds, and the device
will be rebooted.
Restore Factory Settings
Press the button for over 5 seconds, and the device will
restore the factory settings.
1.2 Appearance
The RG-RAP6262(G) provides a Wi-Fi indicator, a SYS indicator, and two LAN port indicators.
Figure 1-1 Appearance
1.3 Ports
Figure 1-2 Ports

Hardware Installation and Reference Guide 1 Product Overview
5
Note
1. 10/100/1000BASE-T Ethernet port
2. DC power supply port
3. 10/100/1000BASE-T Ethernet port/PoE port
4. Reset button
5. Waterproof cap
1.4 Power Supply
The AP supports 802.3at PoE (port LAN 1) or 12 V DC/2 A power supply (If needed, you can buy the adapter
from Ruijie Networks).

·
·
Hardware Installation and Reference Guide Preparing for Installation
6
2 Preparing for Installation
Note
●To prevent device damage and physical injury, please read carefully the safety recommendations
described in this chapter.
●The following safety suggestions do not cover all possible hazardous situations.
●RGRAP6262(G) series AP is aclass Aproduct. In adomestic environment, this product may cause radi
ointerference in which case the user may be required to take adequate measures.
2.1 Grounding and Lightning Protection
Keep the grounding connection within 30 m, and use a 40mm x 4mm or 50mm x 5mm grounding bar of hot-
dip zinc-coated flat steel sheet.
When the connection cable between the main grounding conductor and local equipotential earthing terminal
board (LEB) on each floor is shorter than 2 meters, use a stranded copper wire with a sectional area not less
than 1.318 mm2 (16 AWG) for the connection cable.
Use a shielded network cable if possible, ensure that devices connected to both ends of the shielded network
cable are reliably grounded, and make sure that the sheath of the shielded network cable is also grounded if
possible. If no shielded network cable is available, wire the network cable through a steel pipe and bury the
steel pipe for lead-in, and properly ground both ends of the steel pipe.
No additional lightning protector is required as a high-profile lightning protector is built in the RG-RAP6262(G),
and the antenna port and power port support 6kV lightning protection. If a lightning protector of a higher
profile is available, configure the lightning protector optionally. Before the configuration, connect the lightning
protector to the ground cable.
Use a power cable with the PE end to ground the power supply (AC). Ensure that the PE end is properly
grounded, with a ground resistance less than 5 ohms. Do not use a two-wire power cable with only the live
(L) wire and naught (N) wire. Do not connect the N wire to the protection ground cable of other communication
devices, and ensure that the L wire and N wire are properly connected.
Ensure that the ground resistance is less than 5 ohms. In areas with high soil resistivity, reduce the soil
resistivity via measures such as spreading resistivity reduction mixture around the grounding conductor.
2.2 Preparing the Installation Site
Do not expose the AP to high temperature, dust, or harmful gases.
Do not install the AP in an area prone to fire or explosions.
Keep the AP away from EMI sources such as large radar stations, radio stations, and substations.
Do not subject the AP to unstable voltage, vibration, and noises.
Keep the AP at least 500 meters away from the ocean and do not face it towards the sea breeze.
The installation site should be protected from water and flooding, seepage, dripping, or condensation.

·
·
Hardware Installation and Reference Guide Preparing for Installation
7
The installation site should be selected according to network planning, communications equipment features
and considerations such as climate, hydrology, geology, earthquake, electric power, and transportation.
2.2.1 Temperature and Humidity Requirements
Table 2-1 Temperature and Humidity Requirements
Operating Temperature
Operating Humidity:
-30°C to 65°C (-22°F to 149°F)
0% to 100% RH (non-condensing)
2.2.2 Outdoor Installation
The AP can be installed outdoors and mounted on a wall or a pole.
2.2.3 Waterproof
Use waterproof caps to seal the unused ports.
After using the reset button and DC power port, please ensure that the caps are put back.
The network cable needs to be threaded through the cable gland before connecting to the AP. For details,
see Chapter 3 Installation.
2.2.4 EMI
All interference sources (from outside or inside of the device or application system) affect the device by
capacitive coupling, inductive coupling, or electromagnetic waves.
Electromagnetic interference (EMI) occurs due to electromagnetic radiation or conduction, depending on the
transmission path.
Radiation interference occurs when energy (usually radio frequency energy) is emitted from a device and
propagated through space to disrupt other devices. The interference source can be part of disrupted system or
a fully electrically isolated unit. Conduction interference occurs when interference is transferred from one unit to
another through cables, which are usually electromagnetic wires or signal cables connected between the source
and the device(s) experiencing interference. Conduction interference often affects the power supply of the device.
It is eliminated by using filters. Radiation interference can influence the path of any signal from the device and
is difficult to shield.
Take effective measures against interference from the power grid.
Keep the AP far away from the grounding or lightning protection devices for power equipment.
Keep the AP away from high-power radio stations, radar stations, and high-frequency high-current devices.
Take electrostatic shielding measures.
2.2.5 Installation Tools
Table 2-1 Installation Tools
Tools
Marker, Phillips (crosshead) screwdriver, slotted screwdriver, drill, paper knife,
crimping pliers, diagonal pliers, wire stripper, network cable tester, related power
and fiber cables, wrench, hammer, cable ties, ESD tools, multimeter
The tool kit and cables are customer-supplied.

·
·
Hardware Installation and Reference Guide Preparing for Installation
8
2.3 Checking before Installation
Please check your materials carefully against the package contents. If there are any errors, please contact your distributor.

Hardware Installation Guide and Reference Installing the Access Point
9
3 Installing the Access Point
Note
●Before installing the device, make sure you have carefully read the requirements described in Chapter 2.
3.1 Installation Flowchart
3.2 Before You Begin
Before you install the AP, verify that all the parts in the package contents are there and make sure that:
The installation site meets temperature and humidity requirements.
The installation site is equipped with a proper power supply.
Network cables are in place.
3.3 Precautions
The outdoor AP can be mounted on a wall and a pole (diameter: 50 mm to 70 mm). If the diameter of the pole is
out of the range, the hose clamp is customer-supplied. In this case, it is recommended that you use a hose clamp
with thickness of 2.5mm at least. The installation site varies due to on-the-spot surveys conducted by technical
personnel.

Hardware Installation Guide and Reference Installing the Access Point
10
Please make full preparations as described in Chapter 2 and observe the following precautions before installing
the device.
Before connecting the power supply, make sure the external power supply matches the power module of the
AP.
Before connecting the power cord, make sure the power module is turned off.
When connecting the power cord to a binding post, make sure their colors are the same.
Make sure the power supply is properly connected.
3.4 Installing the Device
3.4.1 Wall Mounting
Use the mounting plate and expansion bolts to implement wall mounting.
1. Attach the mounting plate to the wall (ensure that the semicircle opening is downward vertically) and mark
the locations of screw holes. Secure the mounting plate on the wall with M8 x 60 expansion bolts.
Figure 3-1 Installing the Mounting Plate
2. Install the access point and the connecting rod to the mounting plate on the wall, and tighten the M8 x 20
screws to complete installation.
Figure 3-2 Wall Mounting
3.4.2 Vertical Pole Mounting
1. Secure the mounting plate to the vertical pole by threading two clamps through the mounting plate, and
fasten the clamps with screws.

Hardware Installation Guide and Reference Installing the Access Point
11
Figure 3-3 Mounting the Plate on a Pole
2. Install the access point and the connecting rod to the mounting plate with M8 x 20 screws.
Figure 3-4 Vertical Pole Mounting
3.4.3 Horizontal Pole Mounting
Figure 3-5 Mounting the Plate on a Pole

Hardware Installation Guide and Reference Installing the Access Point
12
Figure 3-6 Horizontal Pole Mounting
Note
The procedures of horizontal pole mounting are similar to that of vertical pole mounting.
3.5 Connecting Cables
Caution
The waterproof materials are customer-supplied.
1. Trim an Ethernet cable according to the distance between the access point and the power supply.
2. Insert the unterminated end of the Ethernet cable through part D, C and B in sequence.
3. Install an RJ45 connector on the unterminated end of the Ethernet cable with an Ethernet cable installation
tool.
4. Insert the RJ45 connector into the LAN 1/PoE/uplink port of the access point, and tighten part B, C and D in
sequence.
5. If you want to install the cable gland without an Ethernet cable threaded through it, insert the waterproof
rubber rod into the washer (rubber gasket), and tighten part B, C and D in sequence.
Caution
Please ensure that the RJ45 connector is properly inserted. Otherwise, the connector may be damaged when
the waterproof cap is tightened. Before removing the network cable, please remove the waterproof cap first and
then the RJ45 connector.

Hardware Installation Guide and Reference Installing the Access Point
13
Warning
The device should not be installed in the place prone to water accumulation, seepage, dripping, and
condensation.
It is recommended to install the device horizontally.
If any requirement above cannot be fulfilled, please use waterproof duct tape and waterproof plaster.

Hardware Installation Guide and Reference Appendix A Connectors and Media
14
4 Appendix A Connectors and Media
1000BASE-T/100BASE-TX/10BASE-T
The 1000BASE-T/100BASE-TX/10BASE-T is a 10/100/1000 Mbps auto-negotiation port that supports auto
MDI/MDIX.
Compliant with IEEE 802.3ab, 1000BASE-T requires Category 5e 100-ohm UTP or STP (STP is recommended)
with a maximum distance of 100 meters (328 feet).
1000BASE-T requires all four pairs of wires be connected for data transmission, as shown in Figure 7-1.
Figure 4-1 1000BASE-T Connection
10BASE-T uses Category 3, 4, 5 100-ohm UTP/STP and 1000BASE-T uses Category 5 100-ohm UTP/STP for
connections. Both support a maximum length of 100 meters. Figure A-2 shows100BASE-TX/10BASE-T pin
assignments.
Figure 4-2 100BASE-TX/10BASE-T Pin Assignments
Figure 4-3 shows wiring of straight-through and crossover cables for 100BASE-TX/10BASE-T.

Hardware Installation Guide and Reference Appendix A Connectors and Media
15
Figure 4-3 100BASE-TX/10BASE-T Connection

Hardware Installation Guide and Reference Appendix B Package Contents
16
5 Appendix B Package Contents
Item
Quantity
Remark
RG-RAP6262(G) Access Point
1
Mounting Plate
1
Connecting Rod (Pre-installed on Access Point)
1
M8 x 20 Screws
2
Cable Glands (Pre-installed on Access Point)
2
Pole Clamps
2
Expansion Bolts (M8 x 60)
4
Quick Start Guide
1
Management Software
1
Installed on the access
point upon delivery