Ruijie RG-AP110-L Installation and operating manual

Ruijie RG-AP110-L Access Points
Hardware Installation and Reference Guide V1.0

Copyright Statement
Ruijie Networks©2019
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,
modification, transmission, translation or commercial use of this document or any portion of this document,
in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice.
Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to
ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to
content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [email protected]
Skype: [email protected]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of
data.

·
Hardware Installation and Reference Guide Product Overview
1Product Overview
RG-AP110-L, which features a simple design and is easy to deploy, is designed for SMB scenarios. This 802.11n-based
AP can be installed on an 86-type faceplate mounting box without damaging interior trim, which makes it an ideal choice
for SMBs like hotels.
1.1 Technical Specifications
Table 1-1 Technical Specifications of RG-AP110-L
Hardware Specifications
Hardware Version
V1.00
Operating Bands
802.11b/g/n: 2.4 GHz to 2.4835 GHz
Spatial Streams
2 streams, 2x2 MIMO
Max Throughput
Up to 300Mbps
Max Transmit Power
<100mw (20dBm, RF card transmit power only)
(Depending on the country of use, laws and regulations.)
Dimensions
(W x D x H)
86 mm x 86 mm x 31 mm
Weight
0.1 kg
Service Ports
One 10/100Base-T WAN port
One 10/100Base-T LAN port
Reset Button
Support
LED Indicator
Support
Power Supply
Support 802.3af and 802.3at PoE power supply
Not support local power supply
Antenna
Built-in omnidirectional antenna (Base gain 2 dBi)
Power Consumption
< 5W
IP Rating
IP41
Operating: 0°C to 40°C (32°F to 104°F)
Temperature
Storage: -40°C to 70°C (-40°F to 158°F)
Operating: 5% to 95% RH (non-condensing)
Humidity
Storage: 5% to 95% RH (non-condensing)
MTBF
>250,000H
RG-AP101-L is a class A product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
1.2 Product Image
The AP provides two service ports: one 10/100Base-T LAN port on the front panel, and one 10/100Base-T WAN port on
the rear panel.

·
Hardware Installation and Reference Guide Product Overview
Figure 1-1 Front View of RG-AP110-L
Figure 1-2 Rear View of RG-AP110-L
1.3 LED Indicator and Reset Button
Figure 1-3 Indicator and Reset Button on the AP

·
Hardware Installation and Reference Guide Product Overview
LED/Button
Frequency
Meaning
Fast blinking
(2.5Hz)
Initialization is in progress.
Solid
AP is operational and CAPWAP connection is established. No STA is
associated.
Double blinking
(1Hz)
Ethernet link is down.
Single blinking
(1Hz)
Ethernet link is up. No CAPWAP connection is established.
System
(Blue)
Slow blinking
(0.4Hz )
AP is operational and CAPWAP connection is established. At least one
STA is associated.
Pressed for less
than 1s
Restarts the device.
Reset
Button
Pressed for more
than 5s
Restores all default settings.

·
Hardware Installation and Reference Guide Preparing for Installation
2Preparing for Installation
2.1 Safety Suggestions
To ensure normal operation and a prolonged useful life of the equipment, the installation site must meet the following
requirements.
To prevent device damage and bodily injury, please read carefully the safety recommendations described in this chapter.
Keep the device away from liquid.
Keep the device away from any heat source.
Wear antistatic wrist strap when installing the device.
Do not wear loose clothes or accessories that may be hooked or caught by the device during installation and
maintenance.
Do not place the equipment in a walking area.
UPS is recommended to prevent power failure and power interference.
The recommendations do not cover all possible hazardous situations.
Use Cat 5 or more advanced cables for connection.
2.2 Installation Site Requirements
2.2.1 Temperature and Humidity
Required operating temperature and humidity are as follows:
Temperature: 0°C to 40°C (14°F to 104°F)
Humidity: 5% to 95% (non-condensing)
2.2.2 Cleanness
Dust poses a serious threat to device operation. Dust that falls onto the surface of the device can be absorbed onto metal
contact points by static electricity, resulting in poor contact. Electrostatic absorption of dust occurs more easily when the
relative humidity is low, which may shorten the service life of the device and cause communication failures. Table 2-2
shows the maximum concentration and diameter of dust allowed in the equipment room.
Table 2-1
Maximum diameter (μm)
0.5
1
3
5
Maximum concentration
(Particles/m3)
1.4 x 107
7 x 105
2.4 x 105
1.3 x 105

·
Hardware Installation and Reference Guide Preparing for Installation
Besides, the contents of salts, acids and sulfides in the air are also strictly limited for the equipment room. These
substances can accelerate metal corrosion and the aging of some parts. Table 2-3 describes the limit of some hazardous
gases such as SO2, H2S, NO2and Cl2 in the equipment room.
Table 2-2
Gas
Average (mg/m3)
Maximum (mg/m3)
SO2
0.2
1.5
H2S
0.006
0.03
NO2
0.04
0.15
NH3
0.05
0.15
Cl2
0.01
0.3
2.2.3 Static Discharge Damage Prevention
To prevent damage from static electricity, pay attention to the following:
Indoor dust prevention
Proper humidity conditions
2.2.4 EMI Consideration
Effective measures should be taken for the power system to prevent the interference from the electric grid.
The working ground of the access point should be properly separated and kept as far as possible from the grounding
device of the power equipment or the anti-lightning grounding device.
Keep the equipment away from high-power radio transmitter, radar transmitting station, and high-frequency
large-current device.
Measures must be taken to isolate static electricity.
2.3 Installation Tools
Installation Tools
Phillips screwdriver, straight screwdriver, wire cutter, cable clamp, cables
The listed tools are customer supplied.

·
Hardware Installation and Reference Guide Installing the Access Point
3Installing the Access Point
Make sure you have carefully read Chapter 2, and be sure that the requirements set forth in Chapter 2 have been
met.
1. Remove the 86-type faceplate from the wall with a screwdriver.
Figure 3-1 Removing the 86-Type Faceplate
2. Connect the Ethernet cable to the WAN port.
Figure 3-2 Connecting the Cable
3. Align the screw holes on both sides of the device over those on the bottom plate.
Figure 3-3 Aligning the Screw Holes

·
Hardware Installation and Reference Guide Installing the Access Point
4. Attach the faceplate cover onto the access point.
Figure 3-4 Attaching the Cover