Ruijie RG-WLAN Series User manual

RG-WLAN Series Access Point
Web-Based Configuration Guide
Release 10.4 (1b19)p2
Version: V3.0

Copyright Statement
Ruijie Networks©2014
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
, , , , ,
, ,, ,
, , are registered trademarks of Ruijie Networks.
Counterfeit is strictly prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual matches the RGOS 10.4 (1b19)p2.
Audience
This manual is intended for:
Network engineers
Technical support and servicing engineers
Network administrators
Obtaining Technical Assistance
Ruijie Networks website: http://www.ruijienetworks.com/
Online customer services: http://webchat.ruijie.com.cn
Customer service center: http://www.ruijie.com.cn/service.aspx
Customer services hotline: [phone]
BBS:
http://support.ruijie.com.cn
Customer services email: [email protected]
Related Documents
Documents Description
Command Reference Describes the related configuration commands, including command
modes, parameter descriptions, usage guides, and related examples.
Hardware Installation and Reference
Guide
Describes the functional and physical features and provides the device
installation steps, hardware troubleshooting, module technical
specifications, and specifications and usage guidelines for cables and
connectors.
Conventions
This manual uses the following conventions:
Convention Description
boldface font Commands, command options, and keywords are in boldface.
italic font Arguments for which you supply values are in italics.
[ ] Elements in square brackets are optional.

{ x | y | z } Alternative keywords are grouped in braces and separated by vertical
bars.
[ x | y | z ] Optional alternative keywords are grouped in brackets and separated by
vertical bars.
Symbols
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment
damage or loss of data.

Configuration Guide Configuring Web Management
Configuring Web Management
Understanding Web Management
Overview
Web management manages wireless network devices through browsers like IEs.
Working Principle
Web management involves a Web server and Web clients. The Web server is deployed on an AP to receive and
process requests from Web clients (reading Web files or executing request commands), and returns processing
results to the clients. A Web client usually refers to a Web browser, such as an IE.
Protocol Specification
None
Requirements for Clients
Administrators usually log in to the AP Web management interface through a client Web browser to manage
the AP. Clients are often PCs or other mobile terminal devices, such as a laptop or an iPad.
Browsers include Google Chrome, Firefox, and IEs, including IE6.0, IE7.0, IE8.0, and IE core-based
browsers like Maxthon
The recommended resolutions are 1024x768, 1280x1024, and 1440x960. Other resolutions may make
characters and formats on pages unaligned and unpleasant.
Requirements for Server
The Web service needs to be enabled on the AP.
Web login authentication information needs to be configured on the AP.
A management IP address needs to be configured on the AP.
Default Configuration
Web service is enabled by default. You can enter 192.168.110.1 in address bar of the browser. Please refer to
Typical Configuration Examples of Web Management for specific CLI configuration steps.
Default Username and Password Description
admin / admin Administrator with all permissions

Configuration Guide Configuring Web Management
If the first configuration for an AP is not performed through Web (such as CLI configuration and the
associated AC configuration), the AP will disable the Web service. If you want to manage the AP
through Web later, please enable Web service manually.
When entering values of configuration items (such as port description and VLAN description) via CLI,
please try not to use spaces. Otherwise an error may occurred in Web Management.
Configuring Web Management
Enter the management IP address of the AP (such as http://192.168.110.1) into the browser address bar and
press Enter to display the following page.
Figure 1 Initial Interface
Please enter your user name and password and click Login. If you pass the authentication, the system home
page is displayed. When logging in to the system at the first time, you enter the Configuration Wizard interface.
When logging in again, you enter the monitoring home page.
System Home Page
Click the System Home Page menu to enter the following page.

Configuration Guide Configuring Web Management
Figure 2 System Home Page
Configuration description: System Home Page helps users learn about AP status and general network
information as follows:
AP resource status
Interface traffic tendency
Current client status
AP resource status: Display the CPU utilization of the current AP, sizes of the available memory and flash
memory, and the number of online STAs..
Interface traffic tendency: Display the real-time tendency of received and sent traffic on the port specified in the
drop-down box.
Current user status: Display the proportion of STAs with strong RSSI, middle RSSI, and low RSSI.
Configuration Wizard
Click the Configuration Wizard menu to enter the configuration wizard home page, where the Configuration
Steps can be executed.
Configuration Wizard will guide you to complete the Wireless Smart Web network deployment.

Configuration Guide Configuring Web Management
Configuration Steps
Figure 3 Configuration Steps
Configuration description: WiFi name (SSID): Configure a name for a wireless network.
WiFi Password: The authentication password that user entered to associate the WiFi
DHCP service: If there is no DHCP server in the network, enable the DHCP service for the wireless network.
Configuration Steps
Monitoring
Client Info
Click the Client Info menu to enter the following page.
Figure 5 Client Info
Configuration description:
Details: To check details about the specified STA.
Block: Add the STA to the blacklist.

Configuration Guide Configuring Web Management
Neighboring APs
Click the Neighboring APs menu to enter the following page, which includes the sub-pages of Rogue APs and
Interference APs.
Rogue APs
Figure 8 Rogue APs
Configuration description:
This page display rogue AP information detected by the system.
Interference APs
Figure 9 Interference APs
Configuration description:
This page display interference AP information detected by the system.
System Logs
Click the System Log menu to enter the following page.

Configuration Guide Configuring Web Management
Figure 10 System Logs
Configuration description
You can query the system log by entering the keyword.
Network Configuration
Port Management
Click the Port Configuration menu to enter the following page, which includes the sub-pages of Basic
Configuration, Port Aggregation and Port Mirroring.
Figure 11 Port Management
Configuration description:
Edit a port: Click Edit in the table above to open the window of Figure 12.